ADA INSTRUMENTS CUBE 360 Green Line Laser User Manual
- June 3, 2024
- ADA INSTRUMENTS
Table of Contents
ADA INSTRUMENTS CUBE 360 Green Line Laser
THE MANUFACTURER RESERVES THE RIGHT TO MAKE CHANGES (NOT HAVING AN IMPACT ON
THE SPECIFICATIONS) TO THE DESIGN, AND COMPLETE SET WITHOUT GIVING PRIOR
WARNING.
APPLICATION
Line laser ADA Cube 360 Green is designed to check the horizontal and the
vertical position of the surfaces of the elements of building structures and
also to transfer the angle of inclination of the structural part to similar
parts during construction and installation work.
SPECIFICATIONS
- Laser beam …………………………………………….Horizontal line 360°/vertical line
- Light sources ………………………………………… 2 laser diodes with laser emission wavelength of 532 nm
- Laser safety class …………………………………. Class 2, <1mW
- Accuracy ………………………………………………… ±3mm/10m
- Self-leveling range ………………………………… ±4°
- Operating range with/without receiver …… 230/130 ft (70/40 m)
- Power source ………………………………………… Li-ion battery 3.7 V / 3xAA 1,5V
- Tripod thread ………………………………………… 2×1/4”
- Operating temperature ……………………….. -5°C +45°C
- Weight ……………………………………………………. 0,86 lb (390 g)
FUNCTIONAL DESCRIPTION
- Emitting a horizontal and vertical laser line.
- Quick self-leveling: when line accuracy is out of the range the laser line flashes and the warning sound is produced.
- Compensator locking system for safe transportation.
- Intermediate compensator locking system for slope operation.
- Indoor and outdoor performance function.
LASER LINES
FEATURES
- Vertical laser beam (V) / Horizontal laser beam (H)
- Detector mode
- Battery compartment
- Tripod mount 1/4’’
- Compensator switch (ON/X/OFF)
- Vertical laser window
- Horizontal laser window
SAFETY INSTRUCTIONS
Follow safety requirements! Don’t face and stare at laser beam! Line laser is an accurate Instrument, which should be stored and used with care. Avoid shaking and vibrations! Store the Instrument and It’s accessories In the carrying case. In case of high humidity and low temperature, dry out the line laser and clean It after the usage. Do not store the line laser at a temperature below -20°C and above 50°C, otherwise the line laser can be out of action. Don’t put the line laser Into the carrying case If the line laser or case are wet. To avoid moisture condensation Inside the Instrument- dry out the case and laser line laser ! Check regularly Instrument line laser ! Keep the lens clean and dry. To clean the line laser use a soft cotton napkin!
OPERATION
- Before use, remove the battery compartment cover. Insert three batteries into the battery compartment with proper polarity, then put the cover back.
- Set the compensator locking grip (5) into the ON position. If the switch is ON,that means the power is on and the compensator is working. If the switch (5) is in an intermediate position, that means the power is opened,the compensation is still locked, but it will not warn if you issue the slope. It’s the hand mode. If switch (5) is OFF, that means that the line laser is off, and the compensator is also locked.
- Press button (1) to switch the vertical beam on. Press button (1)once again to switch the horizontal beam on. Press button (1) to switch the horizontal and vertical beams on. Switch on only necessary laser lines in order to save battery life.
- Press button (2). The mode “outside” is activated. Press button (2) once again. The tool begins to operate in “inside” mode. Use the detector of laser beam for this mode. See the operating manual for the operation with the detector.
TO CHECK THE ACCURACY
TO CHECK THE ACCURACY OF LINE LASER (SLOPE OF PLANE)
Place line laser on the tripod 5m away from the wall so the horizontal laser
line will be directed to the wall. Switch on the power. The line laser starts
to self-level. Mark point A on the wall to show the contact of laser beam with
the wall. Turn the line laser by 90° and mark points В, С, D on the wall.
Measure distance “h” between the highest and lowest points (these are A and D
points in the picture). If “h”is ≤ 6 mm, the measurement accuracy is good. If
“h” exceeds 6 mm, apply service center.
TO CHECK PLUMB
Choose a wall and set laser 5m away from the wall. Mark point A on the wall,
please note the distance from point A to ground should be 3m. Hang a plumb
line from A point to ground and find a plumb point B on ground. turn on the
laser and make the vertical laser line meet the point B, along the vertical
laser line on the wall and measure the distance 3m from point B to another
point C. Point C must be on the vertical laser line, it means the height of C
point is 3m. Measure the distance from point A to point C, if the distance is
over 2 mm, please, contact with seller to calibrate the laser.
PRODUCT LIFE
Product life of the tool is 7 years. The battery and the tool should never be
placed in municipal waste. Date of production, manufacturer’s contact
information, country of origin are indicated on the product sticker.
CARE AND CLEANING
Please handle the measuring line laser with care. Clean with soft cloth only
after any use. If necessary damp cloth with some water. If line laser is wet
clean and dry it carefully. Pack it up only if it is perfectly dry. Transport
in original container/case only.
Note: During transport On/Off compensator lock (5) must be set to
position “OFF”. Disregarding may lead to damage of the compensator.
SPECIFIC REASONS FOR ERRONEOUS MEASURING RESULTS
- Measurements through glass or plastic windows;
- Dirty laser emitting window;
- After line laser has been dropped or hit. Please check the accuracy;
- Large fluctuation of temperature: if the instrument will beused in cold areas after it has been stored in warm areas (or the other way round) please wait some minutes before carrying out measurements.
ELECTROMAGNETIC ACCEPTABILITY (EMC)
- It cannot be completely excluded that this instrument will disturb other instruments (e.g. navigation systems);
- will be disturbed by other instruments (e.g. intensive electromagnetic radiation nearby industrial facilities or radio transmitters).
LASER CLASS 2 WARNING LABEL ON THE LINE LASER
LASER CLASSIFICATION
The line laser is a laser class 2 laser product according to DIN IEC 60825-
1:2014. It is allowed to use unit without further safety precautions.
WARRANTY
This product is warranted by the manufacturer to the original purchaser to be
free from defects in material and workmanship under normal use for a period of
two (2) years from the date of purchase. During the warranty period, and upon
proof of purchase, the product will be repaired or replaced (with the same or
similar model at the manufactures option), without charge for either part of
labour. In case of a defect please contact the dealer where you originally
purchased this product. The warranty will not apply to this product if it has
been misused, abused or altered. Without limiting the foregoing, leakage of
the battery, and bending or dropping the unit are presumed to be defects
resulting from misuse or abuse.
EXCEPTIONS FROM RESPONSIBILITY
The user of this product is expected to follow the instructions given in the
operators’ manual. Although all instruments left our warehouse in perfect
condition and adjustment the user is expected to carry out periodic checks of
the product’s accuracy and general performance. The manufacturer, or its
representatives, assumes no responsibility of results of a faulty or
intentional usage or misuse including any direct, indirect, consequential
damage, and loss of profits. The manufacturer, or its representatives, assumes
no responsibility for consequential damage, and loss of profits byany disaster
(earthquake, storm, flood …), fire, accident, or an act of a third party
and/or a usage in other than usual conditions. The manufacturer, or its
representatives, assumes no responsibility for any damage, and loss of profits
due to a change of data, loss of data and interruption of business etc.,
caused by using the product or an unusable product. The manufacturer, or its
representatives, assumes no responsibility for any damage, and loss of profits
caused by usage other thsn explained in the users’ manual. The manufacturer,
or its representatives, assumes no responsibility for damage caused by wrong
movement or action due to connecting with other products.
THE WARRANTY DOESN’T EXTEND TO THE FOLLOWING CASES:
- If the standard or serial product number will be changed, erased, removed, or wil be unreadable.
- Periodic maintenance, repair or changing parts as a result of their normal runout.
- All adaptations and modifications with the purpose of improvement and expansion of normal sphere of product application, mentioned in the service instruction, without tentative written agreement of the expert provider.
- Service by anyone other than an authorized service center.
- Damage to products or parts caused by misuse, including, without limitation, misapplication or nrgligence of the terms of service instruction.
- Power supply units, chargers, accessories, wearing parts.
- Products, damaged from mishandling, faulty adjustment, maintenance with low-quality and non-standard materials, presence of any liquids and foreign objects inside the product.
- Acts of God and/or actions of third persons.
- In case of unwarranted repair till the end of warranty period because of damages during the operation of the product, it’s transportation and storing, warranty doesn’t resume.
WARRANTY CARD
- Name and model of the product __
- Serial number___
- Date of sale__
- Name of commercial organization ____stamp of commercial organization
The warranty period for the instrument exploitation is 24 months after the
date of the original retail purchase. During this warranty period, the owner
of the product has the right for free repair of his instrument in case of
manufacturing defects. Warranty is valid only with the original warranty card,
fully and clearly filled (stamp or mark of thr seller is obligatory).
Technical examination of instruments for fault identification which is under
the warranty is made only in the authorized service center. In no event shall
the manufacturer be liable before the client for direct or consequential
damages, loss of profit or any other damage which occur in a result of the
instrument outage. The product is received in the state of operability,
without any visible damages, in full completeness. It is tested in my
presence. I have no complaints to the product quality. I am familiar with the
conditions of the qarranty service and i agree.
purchaser signature ___
Before operating you should read service instructions! If you have any
questions about the warranty service and technical support contact seller of
this product
ADA International Group Ltd., No.6 Building, Hanjiang West Road #128, Changzhou New District, Jiangsu, China
Made In China
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>