ADA V-1 Metal Pipe Flow Series User Manual

: October 30, 2023
: ADA

Table of Contents

IMPORTANT
Safety Instruction
METAL PIPE FLOW SERIES parts
Usage of METAL PIPE FLOW SERIES
METAL PIPE FLOW SERIES Connection Example
Caution
CUSTOMER SUPPOR
Read User Manual Online (PDF format)
Download This Manual (PDF format)

ADA V-1 Metal Pipe Flow Series

ADA V-1 Metal Pipe Flow Series

IMPORTANT

Before the installation of this product, make sure to read this instruction manual carefully and understand all its directions.
Please keep this instruction manual even after reading it and refer back to it when needed.

Safety Instruction

This product is designed for growing and maintaining aquatic plants and tropical fish in an aquarium. Please do not use this product for improper purposes.
Read this instruction manual carefully and follow its direction for using this product.
DA is not responsible for death and/or disease of aquatic plants or organisms.
This product is made of stainless steel and may be deformed if dropped and subjected to impact or if force is applied unintentionally.
Although the product is finished carefully, special care should be given to avoid a possible injury when handling the product since an edge of a stainless-steel part may be sharp or there might be a burr.
KEEP OUT OF REACH OF CHILDREN

METAL PIPE FLOW SERIES parts

Metal Pipe Flow Series Parts

Usage of METAL PIPE FLOW SERIES

The METAL PIPE FLOW SERIES is used by connecting it to the hose of an external filter such as the SUPER JET FILTER. Make sure that the outside diameter of the pipe matches the inside diameter of the external filter hose to be used.

METAL PIPE FLOW P-1 Pipe diameter:
Ø13 Compatible with Clear Hose: Inner diameter 12mm / Outer diameter 16mm
METAL PIPE FLOW V-1 Pipe diameter:
Ø13 Compatible with Clear Hose: Inner diameter 12mm / Outer diameter 16mm
METAL PIPE FLOW V-2 Pipe diameter:
Ø17 Compatible with Clear Hose: Inner diameter 15mm / Outer diameter 20mm

METAL PIPE FLOW has two types of pipes, Outflow and Inflow. After attaching the Suction cup, firmly connect the Inflow and Outflow hoses of an external filter. Insert the hose more than 2cm.
Fix the METAL PIPE FLOW with Suction cup to the outside of the tank. Then, start the external filter according to the instruction manual of the external filter.
The MEATL PIPE FLOW for Outflow consists of two parts, such as the outflow nozzle and the pipe itself. The outflow nozzle can be connected at different angles to adjust the direction of water flow and can also be removed for cleaning.
The METAL PIPE FLOW for Inflow has an end cap on the inflow strainer. By removing the end cap, cleaning becomes easier.

METAL PIPE FLOW SERIES Connection Example

Metal Pipe Flow Series Connection Example

Caution

The METAL PIPE FLOW SERIES is designed for rimless tanks, such as CUBE GARDEN. It may not be able to be installed in rimmed tanks
Use a new hose when connecting to METAL PIPE FLOW. Never use worn hoses as they are inelastic and easy to come off.
If it is difficult to connect the hose and pipe, wet the connection part with water so that it becomes easier to insert the pipe into the hose. Also, if the hose and pipe are difficult to remove, it becomes easier to remove them once the pipe is pushed into the hose.
The outflow nozzle and end cap (for inflow) of the METAL PIPE FLOW can be removed. Be careful not to apply more force than necessary to the spring part of the end cap, as it may deform.
Be sure to push the end cap (for inflow) all the way in to eliminate the gap before use.
The inside of each pipe should be cleaned using SPRING WASHER (optional).
If old leaves or debris from aquatic plants are sucked into the strainer of the METAL
PIPE FLOW for inflow, remove them immediately. If left untreated, the motor of the external filter will be overloaded, resulting in a malfunction or accident.
Be careful of the backflow of water when removing the hose.
Do NOT clean using SUPERGE