WOOD 50102WD Mechanical Timer User Manual
- June 10, 2024
- WOOD
Table of Contents
WOOD 50102WD Mechanical Timer User Manual
24 Hour Heavy Duty Mechanical Timer, 1 Grounded Outlet
Model 50102, 50103 | Item 50102WD, 50103WD
INSTRUCTIONS
-
To set the current time: rotate the dial clockwise until the time lines up with the arrow. Note, PM hours are shaded.
-
To program the timer: begin with all segment pins pulled up. Push the segment pins down for the periods of time you want the timer to be ON. Each segment pin represents 30 minutes: 2 segment pins = 1 hour. Repeats daily.
-
To connect the timer: set the switch on the top of the timer to the position.
Plug device into the timer and turn the device on. Plug timer into wall outlet. -
To override the timer, slide the switch on top of the time to the position. When in the position, the plugged-in device is switch on permanently.
-
In case of power failure: reset the timer as explained above.
SPECIFICATIONS
- 125Vac, 60Hz
- 15A / 1875W Resistive
- 10A / 1250W Tungsten
- 1/2Hp
- Temperature: 0oC~55oC
WARNING: RISK OF ELECTRIC SHOCK
- Plug directly into an electrical outlet.
- Not for use in wet locations.
- For indoor use only.
- Keep children away.
- Do not use to control appliances that contain heating elements such as cooking appliances, heaters, and irons.
- Do not exceed electrical ratings.
- Do not use with extension cords.
CAUTION: DO NOT PLUG IN MORE THAN THE RATED LOAD (SEE RATINGS).
- Find the total watts being used. If watts are not market on the appliance, multiply ampere rating (on nameplate) by 125 volts to determine equivalent watts. For lamps with multiple bulbs, add the wattage on the bulbs.
NOTE: This is a GROUNDED device. It has a grounded plug and one grounded outlet.
WARRANTY
This product is guaranteed to be free of defects in materials and workmanship
for 1 year from the date of purchase. If this product is defective, call
1-800-561-4321 for repair
or replacement parts or return the product to the store from which it was
purchased. Guarantee does not include normal wear and tear.
UNITED STATES AND CANADA
Users of this product are cautioned not to make modifications or changes that
are not approved by Southwire Co, doing so may void the compliance of this
product and may result in the loss of the user’s authority to operate the
equipment.
FCC DIGITAL EMISSIONS COMPLIANCE
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two (2) conditions: (1) This device may not cause harmful
interference and (2) this device must accept any interference received
including interference that may cause undesired operation. This equipment has
been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential
installation. This equipment generates uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
- Reorient or relocate the radio or television receiving antenna.
- Increase the separation between the computer equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the radio or television receiver is connected.
- Consult the dealer or an experienced radio television technician for help.
Canadian Digital Apparatus Compliance CAN ICES-003(B)/NMB-003(B)
Customer Support: 800-561-4321
www.southwire.com
Download PDF:WOOD 50102WD Mechanical Timer User Manual
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>