Solutions MS-070SP Extender Set User Guide
- June 10, 2024
- Solutions
Table of Contents
Solutions MS-070SP Extender Set User Guide
Notices
- This MSolutions product contains electrical components that may be damaged by electrical spikes, surges, electric shock, lightning strikes, etc. Use of surge protection is highly recommended in order to protect and extend the life of your equipment.
- The transmission distances of HDMI over Cat cables are measured using TE CONNECTIVITY 1427071-6 EIA/ TIA-568-B termination (T568B) of cables is recommended for optimal performance. To minimise interference of unshielded twisted pairs in the CAT5e/6 cable, do not run the HDBaseT / Cat5e/6/6a cabling with or in close parallel proximity to mains power cables.
- Do not substitute or use any other power supply other than the enclosed unit, or an MSolutions approved replacement. Do not disassemble either the Transmitter or Receiver units for any reason. Doing so will void the manufacturer’s warranty.
- The terms HDMI and HDMI High-Definition Multimedia Interface, andthe HDMI logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.
- Dolby is a trademark of Dolby Laboratories.
- MSolutions reserves the right to change the specifications of this unit without prior notice. As a result of this, physical representations or graphical elements contained within this userguide may not be accurate.
Introduction
The MSolutions MS-070SP is a 4K HDMI extender using uncompressed HDBaseT
technology to extend 4K UHD & HDR video (10.2Gbps) to a distance of up to 40m
over single CAT cable with 1080p or lower resolutions to up to 70m.
S/PDIF audio return enables the sink to return audio to an audio amplification
or distribution device located remotely to the display.
The extender provides bi-directional RS-232. Bi-directional PoC (Power over
Cable) allows for either the TX or RX to be powered.
Key Features
- Uncompressed extension of HDMI at resolutions up to 4K 60Hz 4:2:0 / 4K 30Hz 4:4:4 using HDBaseT technology
- 4K signal extension to 40m over single CAT including HDR formats suppported under 10.2Gbps
- 1080p or lower video resolutions up to 70m over single CAT
- Supports HDMI pass-through all known HDMI audio formats including Dolby Atmos / DTS:X
- HDBaseT 48V standard PoE support to power RX from the TX
- Bi-directional RS-232 serial pass through
- S/PDIF (Digital Optical Toslink) connectivity (RX to TX)
- CEC (Consumer Electronics Control) pass through
- HDCP2.2 compliant
Video resolution capabilities – 10.2Gbps HDMI 1.4 specification max:
Resolution | Refresh | Chroma | Depth |
---|---|---|---|
4096×2160 (DCI) 3840×2160 | 50Hz / 60Hz 30Hz 24Hz | 4:2:0 4:2:0 / 4:2:2 / 4:4:4 | |
/ RGB 4:2:0 / 4:2:2 / 4:4:4 / RGB | 8-bit 8 / 10 / 12-bit 8 / 10 / 12-bit | ||
1920×1080 | up to 60Hz | 4:4:4 / RGB | up to 16-bit |
1280×720 1024×768 | up to 60Hz | 4:4:4 / RGB | p to 16-bit |
VGA to WUXGA | up to 60Hz |
Connectivity Overview – TX
Front panel:
- HDBaseT Out – connect to Cat cable to receiver
- HDMI In – connect to HDMI source
Rear panel:
- S/PDIF Out – connect to optical device
- RS-232 – use supplied 3-pin phoenix connector to connect to serial device
- Power – connect to supplied 12V 2A power supply (or connect to RX)
Connectivity Overview – RX
Front panel:
- HDBaseT In – connect to Cat cable from transmitter
- HDMI Out – connect to HDMI sink device
Rear panel:
- S/PDIF In – connect to optical audio device or display
- RS-232 – use supplied 3-pin phoenix connector to connect to serial device
- Power – connect to supplied 12V 2A power suply (or connect to TX)
Understanding the LED’s
This MSolutions extender set includes status LED indicators on both the Transmitter and Receiver products to show active connections and to further help integratorsdiagnose potential problems with the associated cabling.
The RJ45 HDBaseT connections on both the transmitter and receiver units have orange and green LED’s.
- The orange LED indicates that the unit is receiving power. The LED will blink continuously.
- The green LED indicates that the unit is communicating with the unit attached to the far side of the link over the Cat cable. The LED will be solid whilst the units are able to host a HDBaseT link across the infrastructure.
- Internal LED’s that may be seen through venting of the product are not indicative of a working / non-working unit.
Cabling for HDBaseT
It is important that the interconnecting Cat cable between the MSolutions
HDBaseT products is terminated using the correct RJ45 pin configuration. The
link Cat cable must be a ‘straight’ (pin-topin) Cat cable and it is advised
that this is wired to the T568B wiring standard as this format is less prone
to EMI (Electro-Magnetic Interference).
When installing Cat cables it is advised that the best possible Cat cable
quality possible is used. HDMI distribution products will only work if used
with Cat5e standard cable or above. MSolutions recommends using a Cat6 (or
higher) cable for installations, especially when running over longer
distances, in areas of high EMI, or with 4K signal distribution.
The HDMI cable infrastructure should be compliant to High-Speed
standards,especially where 4K is being distributed. It is important to
understand that where excessive HDMI cable lengths are used, this brings
increased reduction in signal integrity over distance compared to HDBaseT. It
is therefore recommended to use short HDMI cables to ensure the integrity of
the signal over the link.
For HDBaseT and HDMI testing capabilities, please refer to the MSolutions MS-
TestPro to prove both Cat and HDMI cables can be used for video signal
distribution.
Power
The MS-070SP uses Power over Cable (PoC) to provide bi-directional power from either the Transmitter to the Receiver, or Receiver to the Transmitter over the CAT cable link. Please only use the supplied 12V/2A DC PSU supplied with the MSolutions MS-070SP to power the unit.
Audio
The MS-070SP allows for S/PDIF Optical audio signals to be transferred between RX and TX. This enables digital audio signals to be sent in either direction based on requirement of the install.
RS-232 Control
The MS-070SP can distribute bi-directional serial commands between the
transmitter and receiver to allow for control commands to be sent alongside
the video and audio distribution.
Each HDBaseT unit is fitted with a 3-pin Phoenix connector block that will
need the serial TX, RX and Ground pins terminating into. HDBaseT has the
ability to transparently send any type of serial data as both pieces of
equipment are able to communicate using the same baud rate, stop-gap, and
parity.
Specifications
Transmitter
- Video connectivity: 1 x HDMI input (female), 1 x HDBaseT output (RJ45 keystone)
- Digital audio connectivity: S/PDIF Toslink Optical (out)
- RS-232 connectivity: 1 x 3-pin Phoenix connector, block included
- Power supply: 1 x 12V/2A DC
- Individual unit dimensions (W x D x H): 60 x 84 x 25mm
- Individual unit weight: 0.1kg
- Operating temperature: 32°F to 119°F (0°C to 48°C)
- Storage temperature: -4°F to 140°F (-20°C to 60°C)
- Operating humidity: 0-80% non condensing
Receiver
- Video connectivity: 1 x HDBaseT input (RJ45 keystone), 1 x HDMI output (female)
- Digital audio connectivity: S/PDIF Toslink Optical (in)
- RS-232 connectivity: 1 x 3-pin Phoenix connector, block included
- Power supply: 1 x 12V/2A DC
- Individual unit dimensions (W x D x H): 60 x 84 x 25mm
- Individual unit weight: 0.1kg
- Operating temperature: 32°F to 119°F (0°C to 48°C)
- Storage temperature: -4°F to 140°F (-20°C to 60°C)
- Operating humidity: 0-80% non condensing
Package Contents
- 1 x MST-070SP (transmitter)
- 1 x MSR-070SP (receiver)
- 1 x 12V/2A DC power supply with US, UK, and EU clips
- 2 x 3-pin Phoenix connector blocks
- 2 x Surface mounting brackets
Schematic
MS-070SP
Transmitter
MS-070SP
**Receiver
**
Documents / Resources
|
Solutions MS-070SP Extender
Set
[pdf] User Guide
MS-070SP, MS-070SP Extender Set, Extender Set, Set
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>