Design Solutions International DSI HD6471A2 Magnolia 3-Light Matte Black Shaded Pendant Light User Guide

October 30, 2023
Design Solutions International DSI

Item # 321 018 671 / 1007 944 630
Model # HD6471A2
USE AND CARE GUIDE
3-LIGHT PENDANTDesign Solutions International DSI HD6471A2 Magnolia
3-Light Matte Black Shaded Pendant Light Questions, problems, missing parts? Before returning to the store, call Design Solutions International Customer Service
Mon-Fri 9:30 am to 3:00 pm EST
1-800-388-6141 ext. 216
For customer service support and the fastest response, please email us at
CustomerSupport@DSILighting.com

Safety Information

READ AND SAVE THESE INSTRUCTIONS.

  • For your protection and safety, carefully read and understand the information provided in this manual completely before attempting to assemble, install, or operate this product. Failure to do so could lead to electrical shock, fire, or  other injuries that could be hazardous or even fatal.
  • Before touching any wire, use a voltage tester to make sure it is not live.
  • When replacing fuses, turn off the main power first. Make sure your hands and feet are dry, and place one hand behind your back to prevent electricity from making a complete circuit through your chest. Touch the plug fuse only by  its insulated rim. Remove the cartridge fuses with a fuse puller.
  • Use tools with insulated handles and ladders made of wood or fiberglass.
  • To protect children, place a safety cover over any unused outlets.

DANGER: Before starting installation of this fixture or removal of a previous fixture, disconnect the power by turning off the circuit breaker, removing the fuse at the fuse box, or tripping the breaker that controls that circuit. Tape a sign  to the panel warning others to leave the circuit alone while you work.
CAUTION: CONSULT A QUALIFIED ELECTRICIAN IF YOU HAVE ANY ELECTRICAL QUESTIONS. If you have any non-electrical questions about this fixture, please call our Customer Service Team at 1-800-388-6141 ext 216. Please reference item (321 018 671 / 1007 944 630) or UPC (802513199024).

Warranty

THREE (3) YEAR WARRANTY
WHAT IS COVERED
The manufacturer warrants this fixture to be free from defects in materials and workmanship for a period of three (3) years from the date of purchase. This warranty applies only to the original consumer purchaser and only to products  used in normal use and service. If this product is found to be defective, the manufacturer’s only obligation and your exclusive remedy, is the repair or replacement of the product at the manufacturer’s discretion, provided that the product  has not been damaged through misuse, abuse, accident, modifications, alteration, neglect, or mishandling. This warranty shall not apply to any product that is found to have been improperly installed, set-up, or used in any way not in  accordance with the instructions supplied with the product. This warranty shall not apply to a failure of the product as a result of an accident, misuse, abuse, negligence, alteration, faulty installation, or any other failure not relating to faulty material or workmanship.
This warranty shall not apply to the finish on any portion of the product, such as surface and/or weathering, as this is considered normal wear and tear
WHAT IS NOT COVERED
The manufacturer does not warrant and specifically disclaims any warranty, whether expressed or implied, of fitness for a particular purpose, other than the warranty contained herein. The manufacturer specifically disclaims any liability  and shall not be liable for any consequential or incidental loss or damage, including but not limited to any labor/expense costs involved in the replacement or repair of said product
Contact the Customer Service Team at 1-800-388-6141 ext 216 Eastern Time, Mon- Fri 9:30 am to 3:00 pm EST. For customer service support and the fastest response, please email us at CustomerSupport@DSILighting.com.

Pre-Installation

PLANNING INSTALLATION

  • Read all the instructions before installing.
  • To avoid damaging this product, place it on a soft, non-abrasive surface, such as carpet or cardboard.

TOOLS REQUIRED (NOT INCLUDED)

Design Solutions International DSI HD6471A2 Magnolia 3-Light Matte Black
Shaded Pendant Light - TOOLS

HARDWARE INCLUDED
NOTE: Hardware is not shown to actual size.Design Solutions
International DSI HD6471A2 Magnolia 3-Light Matte Black Shaded Pendant Light -
HARDWARE

Part Description Quantity
AA Crossbar assembly (Pre-assembled to fixture body) 1
BB Outlet box screw 3
CC Wire connector 2

PACKAGE CONTENTS

Design Solutions International DSI HD6471A2 Magnolia 3-Light Matte Black
Shaded Pendant Light - PACKAGE

Part Description Quantity
A1 Fixture body A1

Installation

Preparing the crossbar assembly
Unscrew the two mounting balls (1) from the fixture body (A).
Remove the crossbar assembly (AA) from the fixture body (A) and keep the crossbar assembly (AA) and two mounting balls (1) for later use.

Installing the crossbar assembly
Secure the crossbar assembly (AA) to the outlet box (not included) with the outlet box screws (BB). Tighten until snug.
NOTE: The preassembled mounting screws on the crossbar should protrude outward.

Test fitting ceiling canopy on the fixture body to the crossbar assembly

  • Fit the ceiling canopy (2) on the fixture body (A) to the crossbar assembly (AA) and secure with the mounting balls (1).
    If this does not work, adjust the length of the mounting screws on the crossbar assembly (AA) by unscrewing the preassembled hex nuts (3).
    Then, screw the mounting screws in or out of the crossbar assembly (AA) until the desired length is achieved. Once the ceiling canopy (2) on the fixture body (A) is secure,  remove the mounting balls (1) and fixture body (A) and
    proceed to Step 4.

NOTE: The ceiling canopy (2) should be snug against the ceiling and the mounting balls (1).

Design Solutions International DSI HD6471A2 Magnolia 3-Light Matte Black
Shaded Pendant Light - Installation 3

Adjust the cord length
Loosen the set screw on the coupling on the underside of the ceiling canopy.
Adjust the cord in or out of the ceiling canopy according to your hanging height.
Tighten the set screw on the coupling once your hanging height is achieved.
Recommended length, from the top of canopy to bottom of socket, when mounting above a 30 inch high table:
8 foot ceiling: Adjust cord length to 12 in. from the coupling to the ceiling
9 foot ceiling: Adjust cord length to 24 in. from the coupling to the ceiling
10 foot ceiling: Adjust cord length to 36 in. from the coupling to the ceiling
11 foot ceiling: Adjust cord length to 48 in. from the coupling to the ceiling
12 foot ceiling: Adjust cord length to 60 in. from the coupling to the ceilingDesign Solutions International DSI HD6471A2 Magnolia 3-Light Matte
Black Shaded Pendant Light - Installation 4

Cut and strip wires

  • Confirm the desired hanging height. Refer to step 4 if adjustments are needed.
  • Using wire cutters, cut the fixture cord leaving approximately 10 inches of wire extending from the canopy. On the fixture cord, remove 4 inches of the outer sleeve.
  • Using wire strippers, strip each wire 1/2 inch from the end.

Design Solutions International DSI HD6471A2 Magnolia 3-Light Matte Black
Shaded Pendant Light - Installation 5

Making the electrical connections

  • Use wire connectors (CC) to connect the wires.
    Ground Wire:
    Wrap the supply ground wire around the green ground screw on the crossbar (AA), no less than 2 in. from the end of the wire. Tighten the ground screw.
    Connect the fixture ground wire to the supply ground wire with a wire connector (CC).
    Supply Wire:
    Connect the supply white wire to the white fixture supply wire with a wire connector (CC).
    Connect the supply black (or red) wire to the black fixture supply wire with a wire connector (CC).
    Wrap each connection with approved electrical tape and carefully insert all of the connected wires into the outlet box.Design Solutions International DSI
HD6471A2 Magnolia 3-Light Matte Black Shaded Pendant Light - Installation
6

Attaching the fixture body to the outlet box
Re-attach ceiling canopy (2) on the fixture body (A) to the crossbar assembly (AA).
Secure with the previously removed mounting balls (1).

Installing the light bulbs
Install the correct bulbs (not included) referring to fixture markings and/or labels for maximum wattage.
NOTE: Uses three 60W maximum medium base (E26) type “S” or type “A” or 9W maximum medium base (E26) self-ballasted LED vintage Edison bulbs (sold separately).Design Solutions International DSI HD6471A2 Magnolia 3-Light
Matte Black Shaded Pendant Light - bulbs

Care and Cleaning

  • Do not use any cleaners with chemicals, solvents, or harsh abrasives. Use only a dry, soft cloth to dust or wipe carefully.
  • To clean the fixture, disconnect power by turning off the circuit breaker or by removing the fuse at the fuse box, and use a dry or slightly dampened, clean cloth to wipe the exterior surface of the fixture.

Troubleshooting

Problem Possible Cause Solution
The light(s) will not turn on. The bulb is burned out. ❑ Replace the light

bulb.
The power is off.| ❑ Ensure the power supply is turned on.
There is a faulty switch.| II) Test or replace the switch.
There is a faulty wire connection.| ❑ Check the wiring.
The fuse blows or the circuit breaker trips when the light is turned on.| There are crossed wires or the power wire is grounding out.| o Discontinue use of the light.
o Check the wire connections.
o Contact a qualified electrician or call the Customer Care Service Team at 1-800-388-6141 ext 216.
E For customer service support and the fastest response, please email us at CustomerSupportODSILighting.com.

Service Parts

MODEL: HD6471A2Design Solutions International DSI HD6471A2 Magnolia
3-Light Matte Black Shaded Pendant Light - Parts

Part Description
AA Crossbar assembly
BB Outlet box screw
CC Wire connector
A Fixture body

Questions, problems, missing parts? Before returning to the store, call Design Solutions International Customer Service
Mon-Fri 9:30 am to 3:00 pm EST
1-800-388-6141 ext. 216
For customer service support and the fastest response, please email us at
CustomerSupport@DSILighting.com
Retain this manual for future use.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals