milwaukee M12 FDD2, M12 FPD2 Sub Compact Drill Driver Instruction Manual

June 10, 2024
Milwaukee

milwaukee M12 FDD2, M12 FPD2 Sub Compact Drill Driver

Product Information

The product is M12 FDD2 M12 FPD2, a power tool used for drilling and screwing. It comes with an interchangeable battery pack and has two gears with varying speeds and impact ranges. The torque of the tool varies depending on the battery pack used. The drilling capacity ranges from steel to wood to brick and tile. The tool also has a range for drill chuck. It weighs between 2.0 Ah to 4.0 Ah and has recommended ambient operating temperature. The product comes with recommended battery types and chargers. The noise and vibration levels are measured according to EN 62841 standards.

Product Usage Instructions

  1. Before starting any work on the machine, remove the battery pack.
  2. Check the plug and power cord for any damages before use. Only a specialist should repair any damages.
  3. Insert the recommended battery type into the tool.
  4. Adjust the drill chuck to fit the drill bit size needed for the task.
  5. Select the appropriate gear and speed level for the task.
  6. Press the start button to operate the tool.
  7. Adjust the torque control setting depending on the task requirements.
  8. After finishing the task, turn off the tool by pressing the stop button.
  9. Remove the battery pack and store it in a dry place away from direct sunlight and heat sources.
  10. Clean the tool by wiping it with a dry cloth. Do not use water or solvents to clean the tool.

Operating Description And Functional Description

milwaukee-M12-FDD2,-M12-FPD2-Sub-Compact-Drill-Driver-fig-
\(1\)

Remove the battery pack before starting any work on the machine.

milwaukee-M12-FDD2,-M12-FPD2-Sub-Compact-Drill-Driver-fig-
\(2\)milwaukee-M12-FDD2,-M12-FPD2-Sub-Compact-Drill-Driver-fig-
\(3\) milwaukee-M12-FDD2,-M12-FPD2-Sub-Compact-Drill-Driver-fig-
\(4\) milwaukee-M12-FDD2,-M12-FPD2-Sub-Compact-Drill-Driver-fig-
\(5\) milwaukee-M12-FDD2,-M12-FPD2-Sub-Compact-Drill-Driver-fig-
\(6\) milwaukee-M12-FDD2,-M12-FPD2-Sub-Compact-Drill-Driver-fig-
\(7\)

TECHNICAL DATA

milwaukee-M12-FDD2,-M12-FPD2-Sub-Compact-Drill-Driver-fig-
\(9\)

WARNING!
The vibration and noise emission level given in this information sheet has been measured in accordance with a standardized test given in EN 62841 and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure. The declared vibration and noise emission level represents the main applications of the tool. However if the tool is used for diff erent applications, with diff erent accessories or poorly maintained, the vibration and noise emission may diff er. This may signifi cantly increase the exposure level over the total working period.

An estimation of the level of exposure to vibration and noise should also take into account the times when the tool is switched off or when it is running but not actually doing the job. This may signifi cantly reduce the exposure level over the total working period. Identify additional safety measures to protect the operator from the eff ects of vibration and/or noise such as: maintain the tool and the accessories, keep the hands warm, organization of work patterns.

WARNING
Read all safety warnings, instructions, illustrations and specifi cations provided with this power tool. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference.

DRILL SAFETY WARNINGS

Safety instructions for all operations
Hold the power tool by insulated gripping surfaces, when performing an operation where the cutting accessory or fasteners may contact hidden wiring. Cutting accessory or fasteners contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock. Wear ear protectors when impact drilling. Exposure to noise can cause hearing loss.

Safety instructions when using long drill bits

  • Never operate at higher speed than the maximum speed rated of the drill bit. At higher speeds, the bit is likely to bend if allowed to rotate freely without contacting the workpiece, resulting in personal
    injury.

  • Always start drilling at low speed and with the bit tip in contact with the workpiece. At higher speeds, the bit is likely to bend if allowed to rotate freely without contacting the workpiece, resulting the personal injury.

  • Apply pressure only in direct line with the bit and do not apply excessive pressure. Bits can bend causing breakage or loss of control, resulting in personal injury.

ADDITIONAL SAFETY AND WORKING INSTRUCTIONS
Use protective equipment. Always wear safety glasses when working with the machine. The use of protective clothing is recommended, such as dust mask, protective gloves, sturdy non-slip footwear, helmet and ear defenders.

WARNING
To reduce the risk of injury in applications that produce a considerable amount of dust, use a Milwaukee dust extraction solution in accordance with the solution’s operating instructions.

  • The dust produced when using this tool may be harmful to health.
  • Do not inhale the dust. Wear a suitable dust protection mask.
  • Do not machine any materials that present a danger to health (e.g. asbestos).

Switch the device off immediately if the insertion tool stalls! Do not switch the device on again while the insertion tool is stalled, as doing so could trigger a sudden recoil with a high reactive force. Determine why the insertion tool stalled and rectify this, paying heed to the safety instructions.

The possible causes may be:

  • it is tilted in the workpiece to be machined
  • it has pierced through the material to be machined
  • the power tool is overloaded

Do not reach into the machine while it is running. The insertion tool may become hot during use.

WARNING! Danger of burns

  • when changing tools
  • when setting the device down

Chips and splinters must not be removed while the machine is running. When working in walls ceiling, or floor, take care to avoid electric cables and gas or waterpipes. Clamp your workpiece with a clamping device. Unclamped workpieces can cause severe injury and damage. Remove the battery pack before starting any work on the machine. Do not dispose of used battery packs in the household refuse or by burning them. Milwaukee Distributors off er to retrieve old batteries to protect our environment. Do not store the battery pack together with metal objects (short circuit risk).

Use only System M12 chargers for charging System M12 battery packs. Do not use battery packs from other systems. Battery acid may leak from damaged batteries under extreme load or extreme temperatures. In case of contact with battery acid wash it off immediately with soap and water. In case of eye contact rinse thoroughly for at least 10 minutes and immediately seek medical attention. Do not insert the bit on the tool when the tool is running, and switch is lock on status, the bit will be running and may hurt the user.

Warning!
To reduce the risk of fi re, personal injury, and product damage due to a short circuit, never immerse your tool, battery pack or charger in fl uid or allow a fl uid to fl ow inside them. Corrosive or conductive fl uids, such as seawater, certain industrial chemicals, and bleach or bleach containing products, etc., can cause a short circuit.

SPECIFIED CONDITIONS OF USE

  • M12 FDD2: The battery drill/screwdriver may be used for drilling and screwdriving for independent use away from mains supply.
  • M12 FPD2: The electronic battery percussion drill/screwdriver is designed for drilling, percussion drilling, as well as screwdriving for independent use away from mains supply.

Do not use this product in any other way as stated for normal use.

RESIDUAL RISK

Even when the product is used as prescribed, it is still impossible to completely eliminate certain residual risk factors. The following hazards may arise in use and the operator should pay special attention to avoid the following:

  • Injury caused by vibration Hold the product by designated handles and restrict working time and exposure.
  • Exposure to noise can cause hearing injury. Wear ear protection and limit exposure.
  • Injury due to fl ying debris Wear eye protection, heavy long trousers, gloves and substancial footwear at all times.
  • Inhalation of toxic dusts.

NOTES FOR LI-ION BATTERIES

Use of Li-Ion batteries
Batteries which have not been used for some time should be recharged before use. Temperatures in excess of 50°C (122°F) reduce the performance of the battery. Avoid extended exposure to heat or sunshine (risk of overheating).

The contacts of chargers and battery packs must be kept clean. For an optimum life-time, the batteries have to be fully charged, after used. To obtain the longest possible battery life remove the battery pack from the charger once it is fully charged.

For battery storage longer than 30 days:
Store the battery where the temperature is below 27°C and away from moisture Store the battery in a 30% – 50% charged condition Every six months of storage, charge the battery as normal.

Battery protection for Li-Ion batteries
In extremely high torque, binding, stalling and short circuit situations that cause high current draw, the tool will vibrate for about 5 seconds, the fuel gauge will fl ash,and then the tool will turn OFF. To reset, release the trigger. Under extreme circumstances, the internal temperatur of the battery could become to high. If this happens, the fuel gauge will fl ash and the battery pack cool and then continue work.

Transport of Li-Ion batteries
Lithium-ion batteries are subject to the Dangerous Goods Legislation requirements. Transportation of those batteries has to be done in accordance with local, national and international provisions and regulations.

  • The user can transport the batteries by road without further requirements.
  • Commercial transport of Lithium-Ion batteries by third parties is subject to Dangerous Goods regulations. Transport preparation and transport are exclusively to be carried out by appropriately trained persons and the process has to be accompanied by corresponding experts.

When transporting batteries:

  • Ensure that battery contact terminals are protected and insulated to prevent short circuit.
  • Ensure that battery pack is secured against movement within packaging.
  • Do not transport batteries that are cracked or leak.

Check with forwarding company for further advice

CLEANING
The ventilation slots of the machine must be kept clear at all times.

MAINTENANCE

Use only Milwaukee accessories and Milwaukee spare parts. Should components need to be replaced which have not been described, please contact one of our Milwaukee service agents (see our list of guarantee/service addresses). If needed, an exploded view of the tool can be ordered. Please state the machine type printed as well as the six-digit No. on the label and order the drawing at your local service agents or directly at: Techtronic Industries GmbH, Max- Eyth-Straße 10, 71364 Winnenden, Germany.

SYMBOLS

  • Please read the instructions carefully before starting the machine.
  • CAUTION! WARNING! DANGER!
  • Remove the battery pack before starting any work on the machine.
  • Always wear goggles when using the machine.
  • Wear ear protectors!
  • Wear a suitable dust protection mask.
  • Wear gloves!
  • Accessory – Not included in standard equipment, available as an accessory.
  • Do not dispose of waste batteries, waste electrical and electronic equipment as unsorted municipal waste. Waste batteries and waste electrical and electronic equipment must be collected separately.
    • Waste batteries, waste accumulators and light sources have to be removed from equipment.
    • Check with your local authority or retailer for recycling advice and collection point.
    • According to local regulations retailers may have an obligation to take back waste batteries and
    • Waste electrical and electronic equipment free of charge.
    • Your contribution to re-use and recycling of waste batteries and waste electrical and electronic equipment helps to reduce the demand of raw materials.
    • Waste batteries, in particular containing lithium and waste Electrical and electronic equipment contain valuable, recyclable materials, which can adversely impact the environment and the human health, if not disposed of in an environmentally compatible manner.
    • Delete personal data from waste equipment, if any.
  • No-load speed
  • Voltage
  • Direct Current
  • European Conformity Mark
  • British Confomity Mark
  • Ukraine Conformity Mark

DECLARATION OF CONFORMITY

EC DECLARATION OF CONFORMITY
We declare as the manufacturer under our sole responsibility that the product described under “Technical Data” fulfi lls all the relevant regulations and directives listed below and that the following harmonized standards have been used.

  • 2011/65/EU (RoHS)
  • 2014/30/EU
  • 2006/42/EC
  • EN 62841-1:2015
  • EN 62841-2-1:2018+A11:2019
  • EN IEC 55014-1:2021
  • EN IEC 55014-2:2021
  • EN IEC 63000:2018

Winnenden, 2021-12-06

Alexander Krug
Managing Director

Authorized to compile the technical file

  • S.I. 2008/1597 (as amended)
  • S.I. 2016/1091 (as amended)
  • S.I. 2012/3032 (as amended)
  • BS EN 62841-1:2015
  • BS EN 62841-2-1:2018+A11:2019
  • BS EN IEC 55014-1:2021
  • BS EN IEC 55014-2:2021
  • BS EN IEC 63000:2018

Winnenden, 2021-12-06

Alexander Krug
Managing Director

Authorized to compile the technical file:
Techtronic Industries (UK) Ltd
Parkway Marlow SL7 1YL UK

Techtronic Industries GmbH
Max-Eyth-Straße 10 71364 Winnenden Germany.

Copyright 2022

Techtronic Industries GmbH
Max-Eyth-Str. 10 71364 Winnenden Germany
+49 (0) 7195-12-0
www.milwaukeetool.eu.

Techtronic Industries (UK) Ltd
Parkway Marlow SL7 1YL UK.
4931 4706 28

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals