milwaukee M18 FID3-0X Cordless Impact Wrench Instruction Manual
- June 10, 2024
- Milwaukee
Table of Contents
Nothing but HEAVY DUTY M18 FID3
Original instructions
M18 FID3-0X Cordless Impact Wrench
Picture section with operating description and functional description
| 
---|---
| 
| 
TECHNICAL DATA
| M18FID3
---|---
Type| Cordless Impact Screwdriver
Production code| 4812 84 01 XXXXXX MJJJJ
Battery voltage| 18 V ****
No-load speed mode 1 / 2 / 3 /| 0-1700 / 0-3000 / 0-3900 / 0-3300 min-‘
Impact rate mode 1 / 2 / 3| 0-1400 / 0-3600 / 0-4400 min-‘
Torque max.| 226 Nm
Tool reception| HEX 1/4″ (6,35 mm)
Max. diameter bolt / nut| M16
Weight according EPTA-Procedure 01/2014 (2.0Ah…12.0Ah)| 1,5 … 2,6 kg
Recommended ambient operating temperature| -18…+50 °C
Recommended battery types| M18B…; M18HB
Recommended charger| M12-18…; M1418C6
Noise Information
Measured values determined according to EN 62841. Typically, the A-weighted
noise levels of the tool are:
Sound pressure level / Uncertainty K
Sound power level / Uncertainty K Wear ear protectors.| 100,27 dB(A) / 3 dB(A)
111,27 dB(A) / 3 dB(A)
Vibration Information
Total vibration values (vector sum in the three axes) determined according to
EN 62841.
Vibration emission value a, / Uncertainty K| 23,23 m/s2 / 1,5m/s2
WARNING
The vibration and noise emission level given in this information sheet has
been measured in accordance with a standardized test given in EN 62841 and may
be used to compare one tool with another. It may be used for a preliminary
assessment of exposure.
The declared vibration and noise emission level represents the main
applications of the tool. However if the tool is used for diff erent
applications, with diff erent accessories or poorly maintained, the vibration
and noise emission may diff er. This may signifi cantly increase the exposure
level over the total working period.
An estimation of the level of exposure to vibration and noise should also take
into account the times when the tool is switched off or when it is running but
not actually doing the job. This may signifi cantly reduce the exposure level
over the total working period.
Identify additional safety measures to protect the operator from the eff ects
of vibration and/or noise such as: maintain the tool and the accessories, keep
the hands warm, organization of work patterns.
WARNING Read all safety warnings, instructions, illustrations and specifi
cations provided with this power tool. Failure to follow all instructions
listed below may result in electric shock, fi re and/or serious injury. Save
all warnings and instructions for future reference.
IMPACT DRIVER SAFETY WARNINGS
Wear ear protectors. Exposure to noise can cause hearing loss.
Hold the power tool by insulated gripping surfaces, when performing an
operation where the fastener may contact hidden wiring. Fasteners contacting a
“live” wire may make
exposed metal parts of the power tool “live” and could give the operator an
electric shock.
ADDITIONAL SAFETY AND WORKING INSTRUCTIONS
Use protective equipment. Always wear safety glasses when working with the
machine. The use of protective clothing is recommended, such as dust mask,
protective gloves, sturdy non-slip footwear, helmet and ear defenders.
The dust produced when using this tool may be harmful to health. Do not inhale
the dust. Wear a suitable dust protection mask.
Do not machine any materials that present a danger to health (e.g. asbestos).
Switch the device off immediately if the insertion tool stalls! Do not switch
the device on again while the insertion tool is stalled, as doing so could
trigger a sudden recoil with a high reactive force. Determine why the
insertion tool stalled and
rectify this, paying heed to the safety instructions.
The possible causes may be:
- it is tilted in the workpiece to be machined
- it has pierced through the material to be machined
- the power tool is overloaded
Do not reach into the machine while it is running.
The insertion tool may become hot during use.
WARNING! Danger of burns
- when changing tools
- when setting the device down
Chips and splinters must not be removed while the machine is running.
When working in walls ceiling, or floor, take care to avoid electric cables and
gas or waterpipes.
Clamp your workpiece with a clamping device. Unclamped workpieces can cause
severe injury and damage.
Remove the battery pack before starting any work on the machine.
Do not dispose of used battery packs in the household refuse or by burning
them. Milwaukee Distributors off er to retrieve old batteries to protect our
environment.
Do not store the battery pack together with metal objects (short circuit
risk).
Use only System M18 chargers for charging System M18 battery packs. Do not use
battery packs from other systems.
Never break open battery packs and chargers and store only in dry rooms. Keep
dry at all times.
Battery acid may leak from damaged batteries under extreme load or extreme
temperatures. In case of contact with battery acid wash it off immediately with
soap and water. In case of eye contact rinse thoroughly for at least 10
minutes and immediately seek medical attention.
Warning! To reduce the risk of fi re, personal injury, and product damage
due to a short circuit, never immerse your tool, battery pack or charger in fl
uid or allow a fl uid to flow inside them. Corrosive or conductive fl uids, such
as seawater, certain industrial chemicals, and bleach or bleach containing
products, etc., can cause a short circuit.
SPECIFIED CONDITIONS OF USE
The cordless impact wrench can be used to tighten and loosen nuts and bolts
wherever no mains connection is available.
Do not use this product in any other way as stated for normal use.
RESIDUAL RISK
Even when the product is used as prescribed, it is still impossible to
completely eliminate certain residual risk factors. The following hazards may
arise in use and the
operator should pay special attention to avoid the following:
-
Injury caused by vibration.
Hold the product by designated handles and restrict working time and exposure. -
Exposure to noise can cause hearing injury. Wear ear protection and limit exposure.
-
Injury due to fl ying debris Wear eye protection, heavy long trousers, gloves and substancial footwear at all times.
-
Inhalation of toxic dusts.
OPERATION
Note: It is recommended after fastening to always check the torque with a
torque wrench.
The fastening torque is aff ected by a wide variety of factors including the
following.
- State of battery charge – When the battery is discharged voltage will drop and the fastening torque will be reduced.
- Operation at speeds – Operating the tool at low speeds will cause a reduction in fastening torques.
- Fastening position – Holding the tool or the driving fastener in various angles will aff ect the torque.
- Drive accessory/socket – Failure to use the correct size accessory or socket, or a non-impact rated accessory may cause a reduction in the fastening torque.
- Use of accessories and extensions – Depending on the accessory or extension fi tment can reduce the fastening force of the impact wrench.
- Bolt/Nut – Fastening torques may diff er according to the diameter of the nut or bolt, the class of nut/bolt and the length of nut/bolt.
- Condition of the fastener – Contaminated, corroded, dry or lubricated fasteners may vary the fastening torques.
- Condition and base material – The base material of the fastener and any component in between the surfaces may effect the fastening torque (dry or lubricated base, soft or hard base, disc, seal or washer between fastener and base material).
IMPACTING TECHNIQUES
The longer a bolt, screw, or nut is impacted, the tighter it will become.
To help prevent damaging the fasteners or workpieces, avoid excessive
impacting.
Be particularly careful when impacting smaller fasteners because they require
less impacting to reach optimum torque.
Practice with various fasteners, noting the length of time required to reach
the desired torque.
Check the tightness with a hand-torque wrench.
If the fasteners are too tight, reduce the impacting time.
If they are not tight enough, increase the impacting time.
Oil, dirt, rust or other matter on the threads or under the head of the
fastener aff ects the degree of tightness.
The torque required to loosen a fastener averages 75% to 80% of the tightening
torque, depending on the condition of the contacting surfaces.
On light gasket jobs, run each fastener down to a relatively light torque and
use a hand torque wrench for fi nal tightening.
RPM SETTING
The function is designed to reduce screw stripping, screw breakage, and damage
to the work surface when driving self-tapping screws. This function is
optimized for the
most common materials, including #8 – #10 (4.2 – 5.5 mm) self-tapping screws
between 12-25 mm length and 0,5-1 mm sheet metal.
The function will only run if the trigger is pulled more than half-way. If
pulled less than half-way, the driver will run in the normal impacting mode.
When using the
function, the tool will shut off automatically once the screw is fully seated.
NOTES FOR LI-ION BATTERIES
Use of Li-Ion batteries
Batteries which have not been used for some time should be recharged before
use.
Temperatures in excess of 50°C (122°F) reduce the performance of the battery.
Avoid extended exposure to heat or sunshine (risk of overheating).
The contacts of chargers and batteries must be kept clean.
For an optimum life-time, the batteries have to be fully charged, after used.
To obtain the longest possible battery life remove the battery from the
charger once it is fully charged.
For battery storage longer than 30 days: Store the battery where the
temperature is below 27°C and away from moisture
Store the battery in a 30% – 50% charged condition Every six months of
storage, charge the battery as normal.
Battery protection for Li-Ion Akkus
In extremely high torque, binding, stalling and short circuit situations that
cause high current draw, the tool will vibrate for about 5 seconds, the fuel
gauge will fl ash,and then the tool will turn OFF. To reset, release the
trigger.
Under extreme circumstances, the internal temperature of the battery pack
could raise too much. If this happens, the fuel gauge will fl ash until the
battery pack cooled down. After the lights go off , the work may continue.
Transport of Lithium Batteries
Lithium-ion batteries are subject to the Dangerous Goods Legislation
requirements.
Transportation of those batteries has to be done in accordance with local,
national and international provisions and regulations.
-
The user can transport the batteries by road without further requirements.
-
Commercial transport of Lithium-Ion batteries by third parties is subject to Dangerous Goods regulations. Transport preparation and transport are exclusively to be carried out by appropriately trained persons and the process has to be accompanied by corresponding experts.
When transporting batteries: -
Ensure that battery contact terminals are protected and insulated to prevent short circuit.
-
Ensure that battery pack is secured against movement within packaging.
-
Do not transport batteries that are cracked or leak. Check with forwarding company for further advice
CLEANING
The ventilation slots of the machine must be kept clear at all times.
MAINTENANCE
Use only Milwaukee accessories and Milwaukee spare parts.
Should components need to be replaced which have not been described, please
contact one of our Milwaukee service agents (see our list of guarantee/service
addresses).
If needed, an exploded view of the tool can be ordered.
Please state the machine type printed as well as the sixdigit No. on the label
and order the drawing at your local service agents or directly at: Techtronic
Industries GmbH, Max-Eyth-Straße 10, 71364 Winnenden, Germany.
SYMBOLS
| Please read the instructions carefully before starting the machine.
---|---
| CAUTION! WARNING! DANGER!
| Remove the battery pack before starting any work on the machine.
| Do not dispose of waste batteries, waste electrical and electronic
equipment as unsorted municipal waste. Waste batteries and waste electrical
and electronic equipment must be collected separately.
Waste batteries, waste accumulators and light sources have to be removed from
equipment. Check with your local authority or retailer for recycling advice
and collection point. According to local regulations retailers may have an
obligation to take back waste batteries and Waste electrical and electronic
equipment free of charge.
Your contribution to re-use and recycling of waste batteries and waste
electrical and
electronic equipment helps to reduce the demand of raw materials.
Waste batteries, in particular containing lithium and waste Electrical and
electronic equipment contain valuable, recyclable materials, which can
adversely impact the environment and the human health, if not disposed of in
an environmentally compatible manner. Delete personal data from waste
equipment, if any.
| Accessory – Not included in standard equipment, available as an accessory.
| No-load speed
IPM| Impact range
V| Voltage
| Direct Current
| European Conformity Mark
| British Confomity Mark
| Ukraine Conformity Mark
| EurAsian Conformity Mark
Copyright 2022
Techtronic Industries GmbH
Max-Eyth-Str. 10
71364 Winnenden
Germany
+49 (0) 7195-12-0
www.milwaukeetool.eu
Techtronic Industries (UK) Ltd
Parkway
Marlow SL7 1YL
UK (06.22) 4931 4706 27
Documents / Resources
|
milwaukee M18 FID3-0X Cordless Impact
Wrench
[pdf] Instruction Manual
M18 FID3-0X Cordless Impact Wrench, M18 FID3-0X, Cordless Impact Wrench,
Impact Wrench, Wrench
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>