Schneider Electric Wiser IP Camera Outdoor Wiser LK Home Device User Guide

Schneider Electric Wiser IP Camera Outdoor Wiser LK Home Device User Guide

550B1026

Legal Information
The Schneider Electric brand and any trademarks of Schneider Electric SE and its subsidiaries referred to in this guide are the property of Schneider Electric SE or its subsidiaries. All other brands may be trademarks of their respective owners.

This guide and its content are protected under applicable copyright laws and furnished for informational use only. No part of this guide may be reproduced or transmitted in any form or by any means (electronic, mechanical, photocopying, recording, or otherwise), for any purpose, without the prior written permission of Schneider Electric.

Schneider Electric does not grant any right or license for commercial use of the guide or its content, except for a non-exclusive and personal license to consult it on an “as is” basis. Schneider Electric products and equipment should be installed, operated, serviced, and maintained only by qualified personnel. As standards, specifications, and designs change from time to time, information contained in this guide may be subject to change without notice.

To the extent permitted by applicable law, no responsibility or liability is assumed by Schneider Electric and its subsidiaries for any errors or omissions in the informational content of this material or consequences arising out of or resulting from the use of the information contained herein.

Safety information

Important information

Read these instructions carefully and look at the equipment to become familiar with the device before trying to install, operate, service, or maintain it. The following special messages may appear throughout this manual or on the equipment to warn of potential hazards or to call attention to information that clarifies or simplifies a procedure.

The addition of either symbol to a “Danger” or “Warning” safety label indicates that an electrical hazard exists which will result in personal injury if the instructions are not followed.

This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that accompany this symbol to avoid possible injury or death.

Wiser IP Camera Outdoor

550B1026

For your safety

NOTICE
RISK OF DAMAGE TO DEVICE
Always operate the product in compliance with the specified technical data.
Failure to follow these instructions can result in equipment damage.

About the device

The Wiser IP camera outdoor (hereinafter referred to as IP Camera) is a Wi-Fi® operated device that is used to monitor sensitive outdoor areas of your home with a HD recording. You can install the camera indoors or outdoors in all directions (e.g. on the wall, under the roof, etc.). The IP camera can be triggered by other Wiser devices (such as sensors).

Advantages of using an IP camera:

• Increases your overall safety
• High resolution recording
• Covers a wide area
• Infrared night vision for low light recording

NOTE: Users are solely responsible for adhering to applicable privacy laws, e.g. the GDPR, Article 5. Users must ensure that guarantees are taken to avoid any misuse of equipment for surveillance or entirely different and unexpected purposes than intended.

Installing the device
Refer to the installation instruction supplied with this product.
See Wiser IP Camera Outdoor.

Pairing the device
Using the Wiser app, pair your device with the local Wi-Fi network to register on cloud to access and control the device.

Before you pair the device, download the Wiser app to your mobile device.

Follow the steps to pair the device:

Configuring the device

Changing the device icon

You can change the device icon using the Wiser app.

Renaming the device
You can rename the device using the Wiser app.

Changing the device location
You can change the device location using the Wiser app.

Configuring basic function settings
The basic function settings allows you to enable the Status indicator on the device and the Time watermark on the Wiser app.

Status indicator
Enabling the Status indicator turns On/Off the LED on the device.
Follow the steps to enable the Status indicator:

1. On the Home page, tap All devices > IP Camera Outdoor.
2. Tap and tap Settings > Basic function settings.
3. Tap the toggle switch (A) to enable the Status indicator.
   NOTE: The LED indicates blue on the device when the status indicator is turned On.

Time watermark
Enabling the Time watermark displays the date and time on the live view on control panel.
Follow the steps to enable the Time watermark:

1. On the Home page, tap All devices > IP Camera Outdoor.
2. Tap and tap Settings > Basic function settings.
3. Tap the toggle switch (B) to enable the Time watermark.

Configuring IR night vision
The infrared LEDs in the camera allows you to see and record a clear black and white video/image in the dark.
Follow the steps to configure the IR night vision:

1. On the Home page, tap All devices > IP Camera Outdoor.
2. Tap and tap Settings > IR night vision.
3. Select any one of the following options:
   – Auto – Turns on/off automatically when the environmental light is below/ above a certain threshold of the lux level
   – Off – Turns off the IR night vision at all times
   – On – Turns on the IR night vision at all times

Setting image quality
Using the wiser app, you can change the image quality based on your requirement.
TIP: You can switch to Standard Definition image quality when the Wi-Fi is slow or the memory card storage space is less.

1. On the Home page, tap All devices > IP Camera Outdoor.
2. Tap and tap Settings > Image Quality.
3. Select any one of the options:
   – Standard Definition (SD) – Captures low resolution video/image
   – High Definition (HD) – Captures high resolution video/image

Setting offline notification
Using the wiser app, you can receive a notification when the IP camera is offline.
Follow the steps to turn on the Offline notification:

1. On the Home page, tap All devices > IP Camera Outdoor.
2. Tap and tap Settings.
3. Tap the toggle switch (A) to turn on the Offline notification and tap Confirm.

Inserting a micro-SD card
The micro-SD card is inserted in the device to store the recording.

NOTE: The micro-SD card has to be inserted before you power on the device.
If the device is already turned on, then turn off the device to insert the micro-SD card.

Follow the steps to insert a micro-SD card:

1. Remove the lid on the back of the camera.
2. Insert a micro-SD card in the memory card slot.
3. Close the lid.

Once the micro-SD card is inserted, you can configure the playback settings, page 15.

NOTE: A maximum of 128 GB SDHC and SDXC micro-SD cards with FAT32 format are supported.

Removing the device

Using the Wiser app, you can remove a device from the device list.
Follow the steps to remove the device:

TIP: Alternatively, you can long tap on the IP Camera Outdoor on the home page to remove the device.

NOTE:

• Removing the device will reset the device. The LED starts blinking red indicating that the device is ready to pair with another network.
• If there is a problem while pairing, refer to troubleshooting, page 22 the device.

Using the device

Using the control panel of the IP Camera, you can see live video of the outdoors on the display screen and includes the following features:

NOTE:
• To view the notification/alarm messages, tap > Message.
• To review the recordings using playback feature, refer to Playback, page

Using private mode
The Private Mode allows you to turn off the live view, thereby disabling all the other features on the control panel for all users connected to the same Zigbee network. Using this mode, the user is able to stay confidential during private moments.

Follow the steps to turn on the private mode:

1. On the Home page, tap All devices > IP Camera Outdoor.
2. Tap > Settings.
3. Tap the toggle switch to turn on the Private Mode.
4. Alternatively, tap Private Mode (A) on the control panel.

Detection alarm setting
The motion detection function enables the IP camera to detect motion in the surveillance area and display notifications in the Wiser app.

Follow the steps to enable the motion detection:

Alarm sensitivity level

Using the Wiser app, you can adjust the sensitivity level of your motion detector.
Tap Alarm sensitivity level (B) and select any one of the following levels:
– Low
– Medium
– High

NOTE: The high sensitivity level detects the slightest movement and triggers an alarm.

Activity area
Using the Wiser app. you can set the surveillance area for motion detection.

1. Tap the toggle switch (C) to enable the Activity area.
2. Tap Surveillance area settings (D) and drag/resize the red frame to set the surveillance area and tap Save.

NOTE:

• The motion is detected only in the saved surveillance area.
• The privacy zone detection area setting overrides the motion detection activity area setting. Therefore, even if the motion detection activity area is larger than the privacy zone detection area, the motion will only be detected within the privacy zone detection area.

Scheduling detection alarm
Using the Wiser app, you can add a schedule that allows you to turn off/on motion detection automatically based on your needs.
Follow the steps to schedule the motion detection:

1. On the Home page, tap All devices > IP Camera Outdoor.
2. Tap and tap Settings > Motion Detection > Schedule.
3. Tap Add schedule and set the time (A).
4. Tap Repeat (B) and select the days you want the schedule to repeat.
5. Tap Note (C), enter the note and tap Confirm.
6. Tap the toggle switch (D) to turn on the Notification for the schedule.
7. Tap Motion detection (E), select one of the options:
   – On – Turns on the motion detection on the scheduled time
   – Off – Turns off the motion detection on the scheduled time

8. Tap Save.

Setting privacy zone
The Privacy Zone settings allows you to set the surveillance area for monitoring on the live view.
Follow the steps to set the privacy zone:

1. On the Home page, tap All devices > IP Camera Outdoor.
2. Tap and tap Settings > Privacy Zone.
3. Tap the toggle switch (A) to turn on the Privacy Zone.
4. Tap Surveillance area setting (B) and drag/resize the red frame to set the surveillance area and tap Save.
   The live view on the control panel will show only the saved surveillance area.

NOTE: The privacy zone detection area setting overrides the motion detection activity area setting. Therefore, even if the motion detection activity area is larger than the privacy zone detection area, the motion will only be detected within the privacy zone detection area.

Playback
Using the Wiser app, you can review the recording whenever you want with the Playback feature.

NOTE: You need to insert a micro-SD card, page 10 (max 128 GB) to use the playback feature. The control panel of the playback consists of:

NOTE:

• A display screen on the control panel shows the previous recordings.
• The screenshot/recording will be saved in the album.

Recording settings
Follow the steps to change the recording settings:

1. On the Home page, tap All devices > IP Camera Outdoor.

2. Tap and tap Settings > Recording Settings.

3. In the Recording Settings section, tap the toggle switch (A) to enable the Local recording.
   NOTE: The recording will be saved to the micro-SD card.

4. Tap Recording mode (B) and select one of the options:
   NOTE: Recording mode is enabled only when you turn on the Local recording toggle switch.
   – Event recording – Records only when there is a motion detection
   – Non-stop – Records continuously for 24 hours

Scheduling playback
Using the Wiser app, you can add a schedule that allows you to turn off/on recording automatically based on your needs.

Follow the steps to schedule the recording:

1. On the Home page, tap All devices > IP Camera Outdoor.
2. Tap and tap Settings > Recording Settings > Schedule.
3. Tap Add schedule and set the time (A).
4. Tap Repeat (B) and select the days you want the schedule to repeat.
5. Tap Note (C), enter the note and tap Confirm.
6. Tap the toggle switch (D) to turn on the Notification for the schedule.
7. 7. Tap Local recording (E), select one of the options:
   – On – Turns on the recording during the scheduled time
   – Off – Turns off the recording during the scheduled time
   NOTE: The recording will be saved to the memory card.

Creating a moment

A Moment allows you to group multiple actions that are usually done together.
Using the Wiser app, you can create moments based on your needs (such as movie night).

Follow the steps to create a moment:

5. In the Add task menu, you can do either or all of the following actions (C):
– Run the device – Select the devices that you want in a moment
– Select Automation – Select the automation that you want to enable or disable. For more info refer to Automation, page 19.
– Delay – Set the delay time

6. Tap Run the device > IP Camera Outdoor to select either or all of the functions to add in the moment:
– Private Mode – Turn on/off the private mode (D)
– Record Switch – Turn on/off the recording (E)
– Recording Mode – Select the type of recording (F)
– Privacy Area Switch – Turn on/off the privacy zone (G)

7. Once all the actions are set, tap Save.

Editing a moment

To edit a moment:

Deleting a moment

To delete a moment:

Creating an automation
An automation allows you to group multiple actions that are usually done together, triggered automatically or at scheduled times. By using the Wiser app, you can create automations based on your needs.

Follow the steps to create an automation:

4. Tap Any condition is met to select any one of the condition type (B):
– All conditions are met – The automation is triggered when all the conditions are met
– Any condition is met – The automation is triggered when at least one condition is met

5. Tap Add Condition to open the slide-up menu.

6. In the Add Condition menu, you can do either or all of the following options (C):
– When weather changes – Select the various weather settings
– Schedule – Set the time and day
– When device status changes – Select the device and it’s function

7. Tap When device status changes > Window/Door Sensor > Open.
NOTE: : This is an example of an automation to switch on the Event Recording when the Window/Door is Open.
8. Tap Add task to open the slide-up menu.
9. In the Add task menu, you can do either or all of the following options (D):
– Run the device – Select the devices that you want to be triggered
– Moment or Automation – Select the moment which you want to trigger or select the automation that you want to enable or disable
– Send notification – Turn on notification for the automation
– Delay – Set the delay time

10. Tap Run the device > IP Camera Outdoor > Recording Mode

11. Select Event Recording and tap Save.

12. Tap on Effective period to set the time range for the automation. You can select any one of the following (E):
– All-day – 24 hours
– Daytime – From sunrise to sunset
– Night – From sunset to sunrise
– Custom – User defined time period

13. Once all the actions and conditions are set, tap Save.
Once the automation is saved, it is visible on the Automation tab. You can tap the toggle switch on the automation to enable it.

Editing an automation
To edit an automation:

Deleting an automation
To delete an automation:

LED indications

Troubleshooting

Technical Data

Compliance

Compliance information for Green Premium products
Find and download comprehensive information about Green Premium products, including RoHS compliance and REACH declarations as well as Product Environmental Profile (PEP) and End-of-Life instructions (EOLI).

General information about Green Premium products
Click the link below to read about Schneider Electric’s Green Premium product
strategy. https://www.schneider-electric.com/en/work/support/green-premium/

Find compliance information for a Green Premium product
Click the link below to search for a product’s compliance information (RoHS, REACH, PEP and EOLI).
NOTE: You will need the product reference number or product range to perform the search.
https://www.reach.schneider- electric.com/CheckProduct.aspx?cskey=ot7n66yt63o1xblflyfj

Trademarks
This guide makes reference to system and brand names that are trademarks of their relevant owners.

• Zigbee® is a registered trademark of the Connectivity Standards Alliance.
• Apple® and App Store® are brand names or registered trademarks of Apple Inc.
• Google Play™ Store and Android™ are brand names or registered trademarks of Google Inc.
• Wi-Fi® is a registered trademark of Wi-Fi Alliance®.
• Wiser™ is a trademark and the property of Schneider Electric, its subsidiaries and affiliated companies.
  Other brands and registered trademarks are the property of their respective owners.

Printed in:
Schneider Electric
Lautrupvang 1
2750 Ballerup
Denmark
+45 88 30 20 00

Schneider Electric Denmark A/S
Lautrupvang 1, 2750 Ballerup
Denmark
+45 88 30 20 00
www.lk.dk
As standards, specifications, and design change from time to time,
please ask for confirmation of the information given in this publication.
© 2021 – 2022 Schneider Electric. All rights reserved.
DUG_IPC_Outdoor_LK–01

Read More About This Manual & Download PDF:

References

• untitled

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>