HIKVISION TURBO HD H8T Series Bullet Camera User Manual

: June 10, 2024
: Hikvision

Table of Contents

HIKVISION TURBO HD H8T Series Bullet Camera
FCC STATMENT
Introduction
- Product Features
Overview
Installation
Menu Description
FUNCTIONS
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

HIKVISION TURBO HD H8T Series Bullet Camera

User Manual
Thank you for purchasing our product. If there are any questions, or requests, do not hesitate to contact the dealer. This manual applies to the models below:

Type	Model
Type I Camera	DS-2CE16H8T-ITF

Type II Camera

| DS-2CE16H8T-IT1F
DS-2CE16H8T-IT3F
DS-2CE16H8T-IT5F

This manual may contain several technical incorrect places or printing errors, and the content is subject to change without notice. The updates will be added to the new version of this manual. We will readily improve or update the products or procedures described in the
manual.

Regulatory Information

FCC STATMENT

Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

FCC compliance: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

FCC Conditions
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

This device may not cause harmful interference.
This device must accept any interference received, including interference that may cause undesired operation.

EU Conformity Statement

This product and – if applicable – the supplied accessories too are marked with “CE” and comply therefore with the applicable harmonized European standards listed under the Low Voltage Directive 2014/35/EU, the EMC Directive 2014/30/EU. 2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see: www.recyclethis.info. 2006/66/EC (battery directive): This product contains a battery that cannot be disposed of as unsorted municipal waste in the European Union. See the product documentation for specific battery information. The battery is marked with this symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return the battery to your supplier or to a designated collection point. For more information see: www.recyclethis.info.

Industry Canada ICES-003 Compliance
This device meets the CAN ICES-3 (A)/NMB-3(A) standards requirements.

Warning
This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

Safety Instruction
These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss.
The precaution measure is divided into “Warnings” and “Cautions”.
Warnings: Serious injury or death may occur if any of the warnings are neglected.
Cautions: Injury or equipment damage may occur if any of the cautions are neglected.

Warnings

In the use of the device, you must be in strict compliance with the electrical safety regulations of the nation and region.
Input voltage should meet both the SELV (Safety Extra Low Voltage) and the Limited Power Source with 12 VDC according to the IEC60950-1 standard. Refer to technical specifications for detailed information.
Do not connect multiple devices to one power adapter to avoid over-heating or a fire hazard caused by overload.
Make sure that the plug is firmly connected to the power socket.
Make sure that the device is firmly fixed if wall mounting or ceiling mounting is adopted.
If smoke, odor or noise rise from the device, turn off the power at once and unplug the power cord, and then contact the service center.
Never attempt to disassemble the camera by unprofessional personal.

Cautions

Do not drop the camera or subject it to physical shock.
Do not place the camera in extremely hot, cold (the operating temperature shall be -40°C to 60°C), dusty or damp locations, and do not expose it to high electromagnetic radiation.
Do not touch senor modules with fingers.
If cleaning is necessary, use clean cloth with a bit of ethanol and wipe it gently.
Do not aim the camera at the sun or extra bright places.
The sensor may be burned out by a laser beam, so when any laser equipment is in using, make sure that the surface of sensor will not be exposed to the laser beam.
Do not expose the device to high electromagnetic radiation or extremely hot, cold, dusty or damp environment.
To avoid heat accumulation, good ventilation is required for the operating environment.
Keep the camera away from liquid while in use for non-water-proof device.
While in delivery, the camera shall be packed in its original packing, or packing of the same texture.

Mark Description

Table 0-1 Mark Description

Mark	Description
DC Voltage

Introduction

Product Features

The main features are as follows:

High performance CMOS sensor
IR cut filter with auto switch
OSD menu with configurable parameters
Auto white balance
Internal synchronization
SMART IR mode
4 in 1 video output (switchable TVI/AHD/CVI/CVBS)
3-axis adjustment

Overview

This manual applies to two types of bullet cameras. The overviews of each type are shown in the figures below.

Overview of Type I Camera

Note
Press and hold the switch button for 5 seconds to switch the video output. Four kinds of video outputs are available: TVI, AHD, CVI, and CVBS.

Overview of Type II Camera

Note
Press and hold the switch button for 5 seconds to switch the video output. Four kinds of video outputs are available: TVI, AHD, CVI, and CVBS.

Installation

Before you start

Make sure that the device in the package is in good condition and all the assembly parts are included.
Make sure that all the related equipment is power-off during the installation.
Check the specification of the products for the installation environment.
Check whether the power supply is matched with your power output to avoid the damage.
Make sure the wall is strong enough to withstand
three times the weight of the camera and the
bracket.
If the wall is cement, insert expansion bolts before installing the camera. If the wall is wooden, use self-tapping screws to secure the camera.
If the product does not function properly, contact your dealer or the nearest service center. Do NOT disassemble the camera for repair or maintenance by yourself.

Installation of Type I Camera

Ceiling/Wall Mounting without Junction Box Steps:

Paste the drill template (supplied) to the place where you want to install the camera.
Drill the screw holes and the cable hole (optional) in the ceiling/wall according to the drill template.
Note
Drill the cable hole, when adopting the ceiling outlet to route the cable.
Attach the bracket to the ceiling/wall and secure the camera with supplied screws.
Note
- The supplied screw package contains self-tapping screws, and expansion bolts.
- For cement wall/ceiling, expansion bolts are required to fix the camera. For wooden wall/ceiling, self-tapping screws are required.
Route the cables through the cable hole, or the side opening.
Connect the corresponding power cord, and video cable.
Power on the camera to check whether the image on the monitor is gotten from the optimum angle. If not, adjust the camera according to the figure below to get an optimum angle.

Loosen the P screw to adjust the pan position [0° to 360°]. Tighten the screw after completing the adjustment.
Loosen the T screw to adjust the tilt position [0° to 180°]. Tighten the screw after completing the adjustment.
Loosen the R screw and rotate the camera [0° to 360°]. Tighten the screw after completing the adjustment.

Ceiling/Wall Mounting with Junction Box Before you start:

You need to purchase a junction box separately.
Steps

Paste the drill template on the ceiling/wall.
Drill screw holes and the cable hole in the ceiling/wall according to the holes of the drill template.
Take apart the junction box, and align the screw holes of the bullet camera with those on the Junction box’ cover.
Fix the camera on the junction box’s cover with supplied screws.
Attach the junction box body to the ceiling/wall by aligning the screw holes of the junction box.
Secure the junction box’s body with supplied screws on the ceiling/wall.
Route the cables through the bottom cable hole, or the side cable hole of the junction box.
Combine the junction box cover with its body.
Repeat the step 5 and 6 of 2.1.1 Ceiling/Wall Mounting without Junction Box to complete the installation.

Installation of Type II Camera

Ceiling/Wall Mounting without Junction Box
Steps:

Paste the drill template (supplied) to the place where you want to install the camera.
Drill the screw holes according to the drill template, and the cable hole (optional) on the ceiling.
Note:
Drill the cable hole in the center of the drill template, when adopting ceiling outlet to route the cable.
Route the cables through the cable hole (optional) or the side opening.
Fix the camera to the ceiling with supplied screws.
Note:
- The supplied screw package contains self-tapping screws, and expansion bolts.
- For cement wall/ceiling, expansion bolts are required to fix the camera. For wooden wall/ceiling, self-tapping screws are required.
Connect the corresponding power cord, and video cable.
Power on the camera to check whether the image on the monitor is gotten from the optimum angle. If not, adjust the surveillance angle.

Loosen the No.1 adjusting screw to adjust the pan position [0° to 360°]. Tighten the No.1 adjusting screw.
Loosen the No.2 adjusting screw to adjust the tilting position [0° to180°]. Tighten the No. 2 adjusting screw.
Loosen the No.3 adjusting screw to adjust the rotation position [0° to 360°]. Tighten the No.3 adjusting screw.

Ceiling/Wall Mounting with Junction Box Before you start

You need to purchase a junction box separately.
Steps

Paste the drill template on the ceiling/wall.
Drill screw holes and the cable hole (optional) in the ceiling/wall according to the holes of the drill template.
Note:
Drill the cable hole, when adopting ceiling outlet to route the cable .
Take apart the junction box, and align the screw holes of the bullet camera with those on the Junction box’s cover.
Fix the camera on the junction box’s cover with three supplied screws.
Secure the junction box’s body with supplied screws on the ceiling/wall.
Route the cables through the bottom cable hole, or the side cable hole of the junction box.
Combine the junction box cover with its body with supplied screws on the junction box’s cover.
Repeat the step 5 and 6 of 2.2.1 Ceiling/Wall Mounting without Junction Box to complete the installation.

Purpose:
Call the menu by clicking button on the PTZ Control interface, or call preset No.95.
Steps

Connect the camera with the TVI DVR, and the monitor, shown as the figure 3-1.
Power on the analog camera, TVI DVR, and the 5. Click the direction arrow to control the camera. monitor to view the image on the monitor.
Click PTZ Control to enter the PTZ Control interface.
Call the camera menu by clicking button, or call preset No. 95.

Click up/down direction button to select the item.
Click Iris + to confirm the selection.
Click left/right direction button to adjust the value of the selected item.

VIDOE FORMAT
You can set the video format as 5MP@20fps, 4MP@25fps, 4MP@30fps, 2MP@25fps, and 2MP@30fps.

Note:

When switching the video output as CVBS, you can set the video format as PAL, or NTSC.
When switching the video output as AHD, you can set the video format as 5MP@20fps, 4MP@25fps, or 4MP@30fps
When switching the video output as CVI, you can set the video format as 4MP@25fps, or 4MP@30fps.
Click SAVE & EXIT to validate the resolution changing.

EXPOSURE
Exposure describes the brightness-related parameters, which can be adjusted by EXPOSURE MODE, and AGC.

EXPOSURE MODE

You can set the EXPOSURE MODE as GLOBAL, BLC, and WDR.
GLOBAL GLOBAL refers to the normal exposure mode which performs exposure according to the whole image brightness.
BLC (Backlight Compensation) BLC (Backlight Compensation) compensates light for the front object to make it clear, but this may cause the over-exposure of the background, where the light is strong.
WDR (Wide Dynamic Range) The WDR helps the camera provide clear images even under backlight circumstances. When both very bright and very dark areas simultaneously exist in the image, WDR balances the brightness level of the whole image to provide clear images with details. AGC (Automatic Gain Control) It optimizes the clarity of the image in poor light conditions. The AGC level can be set as HIGH, MEDIUM, or LOW.

Note: The noise will be amplified when setting the AGC level. The higher the level is, the more obvious the noise is.

DAY/NIGHT
COLOR, BW (Black White), and AUTO are selectable for DAY/NIGHT switch. COLOR The image is colored in day mode all the time. B & W (Black and White) The image is black and white all the time, and the IR LIGHT turns on in the poor light conditions. You can turn on/off the IR LIGHT and set the value of SMART IR in this menu.

IR LIGHT
You can turn on/off the IR LIGHT to meet the requirements of different circumstances.

SMART IR
The Smart IR function is used to adjust the light to its most suitable intensity, and prevent the image from over exposure. The SMART IR value can be adjusted from 0 to 3. The higher the value is, the more obvious effects are.

AUTO
Automatically switch Color, or BW (Black and White) according to actual scene brightness. You can turn on/off the IR LIGHT, and set the value of SMART IR in this menu.

IR LIGHT
You can turn on/off the IR LIGHT to meet the requirements of different circumstances.

SMART IR
The Smart IR function is used to adjust the light to its most suitable intensity, and prevent the image from over exposure. The SMART IR value can be adjusted from 0 to 3. The higher the value is, the more obvious effects are.

N Threshold (Day to Night Threshold) Day to Night Threshold is used to control the sensitivity of switching the day mode to the night mode. You can set the value from 1 to 9. The larger the value is, the more sensitive the camera is.
Day to Night Threshold is used to control the sensitivity of switching the day mode to the night mode. You can set the value from 1 to 9. The larger the value is, the more sensitive the camera is.
D Threshold (Night to Day Threshold) Night to Day Threshold is used to control the sensitivity of switching the night mode to the day mode. You can set the value from 1 to 9. The larger the value is, the more sensitive the camera is.

VIDEO SETTINGS
Move the cursor to VIDEO SETTINGS and click Iris+ to enter the submenu. IMAGE MODE, WHITE BALANCE, BRIGHTNESS, CONTRAST, SHARPNESS, SATURATION, 3DNR, and MIRROR are adjustable.

IMAGE MODE
IMAGE MODE is used to adjust the image saturation, and you can set it as STD (Standard), or HIGH-SAT (High Saturation).

WHITE BALANCE
White balance, the white rendition function of the camera, is to adjust the color temperature according to the environment. It can remove unrealistic color casts in the image. You can set the mode as AUTO, or MANUAL.

AUTO
Under AUTO mode, white balance is being adjusted automatically according to the color temperature of the scene illumination.

MANUAL
You can set the R-GAIN/B-GAIN value from 1 to 255 to adjust the shades of red/blue color of the image.

BRIGHTNESS
Brightness refers to the brightness of the image. You can set the BRIGHTNESS value from 1 to 9 to darken or brighten the image. The higher the value is, the brighter the image is.

CONTRAST
This feature enhances the difference in color and light between parts of an image. You can set the CONTRAST value from 1 to 9.
SHARPNESS
Sharpness determines the amount of detail an imaging system can reproduce. You can set the SHARPNESS value from 1 to 9.
SATURATION
Adjust this feature to change the saturation of the color. The value ranges from 1 to 9. 3DNR (Digital Noise Reduction) The 3DNR function can decrease the noise effect and deliver more accurate and sharp image. You can set the 3DNR value from 1 to 9.

MIRROR

OFF, H, V, and HV are selectable for mirror.
OFF: The mirror function is disabled.
H: The image flips 180° horizontally.
V: The image flips 180° vertically.
HV: The image flips 180° both horizontally and vertically.

FUNCTIONS

In the FUNCTIONS submenu, you can set the privacy mask, and the motion detection of the camera.
MOTION DETECTION
In the user-defined motion detection surveillance area, the moving object can be detected and the alarm will be triggered. Up to 4 motion detection areas can be configured.

Select a MOTION area. Set the MODE as ON. Click the up/down/left/right button to define the position, and the size of the area. Set the SENSITIVITY from 1 to 9.
PRIVACY
The privacy mask allows you to cover certain areas which you don’t want to be viewed, or recorded. Up to 4 privacy areas are configurable.