BETSTCO FH-SG24 Pro Stump Grinder User Manual
- June 10, 2024
- BETSTCO
Table of Contents
- OPERATION & PARTS MANUAL
- INTRODUCTION
- INTENDED USE
- TECHNICAL SPECIFICATIONS
- GENERAL SAFETY RULES
- PERSONAL SAFETY
- TOOL USE AND CARE
- STUMP GRINDER SET-UP PROCEDURES
- MAINTENANCE
- REPLACING TEETH
- STUMP GRINDER ASSEMBLY & PARTS LIST
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
FH-SG24PRO Stump Grinder
Tighten All Nuts and Bollts!
User Manual
OPERATION & PARTS MANUAL
Please read these instructions before using. Always grease all fittings and be sure to always check and fill with oil before operating! Retain this manual for future use.
INTRODUCTION
Congratulations on your purchase and welcome to FHM. This manual gives you the
necessary information about your machine so you will be able to use it
properly.
The entire manual must be read and understood before you start using the
machine.
If any questions should arise that are not covered by this manual, please
contact FHM.
OWNER’S RECORD
Please take a moment to record the following information about your stump
grinder.
If you need to call for assistance, please be ready to provide your model
number.
This information will allow us to help you more quickly when you call.
MODEL NUMBER
SERIAL NUMBER
DATE OF PURCHASE
This machine is designed for certain applications only. We strongly recommend
this machine is not modified and/or used for any application other than that
for which it was designed. If you have any questions relative to a particular
application, DO NOT use the machine until you have first contacted us to
determine if it can or should be performed on the product.
For technical questions and replacement parts, please contact FHM.
INTENDED USE
This stump grinder is designed for grinding stumps using a tractor PTO at 540 RPM.
TECHNICAL SPECIFICATIONS
Model | SG24 | 5624-PRO |
---|---|---|
Recommended HP | 30 HP – 50 HP | |
Rotor Size | 24″ | |
Number of Teeth | 36 | 54 |
Tooth Construction | Carbide steel bolt-in | |
Required PTO Speed | 540 RPM | |
Cutting Wheel Speed | 950 RPM | |
Cutting Height | 18″ above ground | |
Cutting Depth | 8″ below ground | |
Maximum Cutting Depth (per pass) | 6″ | |
Maximum Horizontal Cut | 26″ | |
Swing Arc | 40° | |
Hitch Category | Cat. I or II | |
Shipping Weight | 280kg |
GENERAL SAFETY RULES
WARNING!
Read and understand all instructions. Failure to follow all instructions
listed below may result in electric shock, fire and/or serious injury.
WARNING!
The warnings, cautions, and instructions discussed in this instruction manual
cannot cover all possible conditions or situations that could occur. It must
be understood by the operator that common sense and caution are factors which
cannot be built into this product, but must be supplied by the operator.
NOTE: All the laws and any regulation having jurisdiction covering the
safety requirements for use of the machine take precedence over the statements
in this manual. Users of this machine must adhere to such regulations.
Only people that have read and understood these instructions are able to use
the stump grinder.
Inspect the stump grinder and tractor at the beginning of every working day
and repair any defects.
Stop the engine and make sure that the machine will not start accidentally
while repairing defects or doing maintenance.
Do not remove the stump grinders safety devices or make them inactive.
Always locate buried wires, cables, and pipelines before grinding.
PERSONAL SAFETY
Stayalert, watch what you are doing and use common sense when operating the
machine. Do not use the machine while you are tired or under the influence of
drugs, alcohol or medication. A moment of inattention while operating machines
may result in serious personal injury.
Dress properly. Do not wear loose clothing, dangling objects, or jewelry. Keep
your hair, clothing and gloves away from moving parts. Loose clothes, jewelry
or long hair can be caught in moving parts. Air vents often cover moving parts
and should be avoided. A Usesafety apparel and equipment.
Use safety goggles or safety glasses with side shields which comply with
current national standards, or when needed, a face shield. Use a dust mask in
dusty work conditions. This applies to all persons in the work area. Also use
safety shoes, hardhat, gloves, dust collection systems, and hearing protection
when appropriate.
Do not over reach. Keep proper footing and balance at all times.
Remove adjusting keys or wrenches before connecting to the power supply or
turning on the tool. A wrench or key that is left attached to a rotating part
of the tool may result in personal injury.
Never conduct any maintenance or make any other adjustments when the engineis
running. Always shut the engine off, remove the ignition key, and keep the
engine off before carrying out any of the aforementioned procedures. Consult
your engine manual for safe shutdown procedures to prevent accident ignition.
Never allow passengers on the stump grinder.
TOOL USE AND CARE
Always be sure operator is familiar with proper safety precautions and
operation techniques before using machine.
Do not force the machine. Machines do a better and safer job when used in the
manner for which they are designed.
****Storing the machine. When the machine is not in use, store it in a dry,
secure place or keep well covered and out of the reach of children. Inspect
the machine for good working condition prior to storage and before re-use. A
Maintain the machine.
It is recommended that the general condition of the machine be examined before
it is used. Keep the machine in good repair by adopting a program
ofconscientious repair and maintenance in accordance with the recommended
procedures found in this manual. If any abnormal vibrations or noise occurs,
turn the machine off immediately and have the problem corrected before further
use.
Cleaning. Use a pressure washer to clean the carbide teeth while taking care
not to pressure wash the bearings as this may introduce water into areas of
the machine that will result in malfunction or damage.
Use only accessories that are recommended by the manufacturer. Accessories
that may be suitable for another machine may create a risk of injury when used
on this machine.
Always operate the machine with all safety devices and guards in place and in
working order. DO NOT modify or make changes to safety devices. DO NOT operate
the machine if any safety devices or guards are missing or inoperative.
Never leave the machine running unattended.
Never use the machine to grind anything other than stumps or for any purpose
other than grinding stumps as described in this manual.
STUMP GRINDER SET-UP PROCEDURES
TRIMMING THE PTO SHAFT
The stump grinder is shipped with a PTO shaft that can be fitted to most
tractors. The PTO shaft may need to be timmed depending on your tractor and
configuration. Follow the below steps to ensure that the PTO shaft is fitted
to your tractor correctly.
-
Attach the stump grinder to the tractor, but do not install the PTO shaft.
-
Raise the stump grinder using the tractors 3 point hitch system so that the shaft on the tractor is level with the shaft on the stump grinder.
-
Measure the distance between the locking grooves on the shaft of the tractor and stump grinder (A) as shown below.
-
Measure the distance between the locking pins on the PTO shaft itself when it is in the compressed/shortest length (B) as shown below.
-
If (A)is atleast 1″ longer than (B), the PTO shaft will not need to be cut.
-
If dimension (B) is longer than (A), the PTO shaft will need to be cut. The below equation may be used to calculate the correct amount to trim.
(B-A) + 1 INCH = C (AMOUNT TO CUT) -
Once (C) has been calculated; this amount will need to be cut off of BOTH halves of the PTO shaft.
-
After both halves of the PTO shaft have been cut, use a file to remove any burrs or sharp edges and slide the shaft together ensuring it telescopes in and out freely.
The PTO shaft can now be attached to the stump grinder and tractor, ready for use.
MAINTENANCE
-
Proper and routine maintenance is critical to operator safety, achieving proper stump grinding results and in prolonging the life of the machine.
-
For cleaning and maintenance of the stump grinder, switch off the tractor PTO shaft and turn the engine off.
-
Inspect the unit before each use for loose nuts and worn cutting teeth. Also clean any build up of debris.
-
After 2 hours of operation, check for loose nuts and worn cutting teeth. Tighten and replace as necessary.
-
Grease the bearings and the pivot pins on the main housing as needed before each use.
Do not over grease the the bearings as this will blow out the seals and cause premature bearing failure. -
Inspect the clutch plates on the PTO shaft periodically to ensure that they are not seized together. Refer to “PTO Shaft Clutch Run In” in the “Stump Grinder Set Up
Procedures” section of the manual.
REPLACING TEETH
- Disconnect the PTO shaft from the tractor and set the stump grinder on a flat and level surface.
- Remove the lock nut using a wrench or socket.
- Remove the cutting tooth.
- Install a replacement tooth and lock nut using a torque wrench set to 160 ft-Ibs (215 Nm)
STUMP GRINDER ASSEMBLY & PARTS LIST
NO.| PART NO.| Name & Specifications Quantity|
---|---|---|---
1| GB/T5783-2000| Bolt M8x20| 3
2| GB/ T93-1987| Spring washer 8| 3
3| GB/T97.1-2002| Plain washer 8| 3
4| 5G24.01.011| Pin weldment| 3
5| SG24.01.012| Swing frame weldment| 1
6| JB/T7940.1-1995| Oil cup M8| 4
7| SG24.01.013| Pivot cross| 1
8| SG24.01.014| 3-Pt. toke weldment| 1
9| | Lock pin| 2
10| SG24.01.101| Pin for lifting| 2
11| SG24.01.015| Hose, Horizontal| 2
12| SG24.01.016| Hydraulic cylinder, Horizontal| 1
13| JB/T 982-1977| Casket 16| 8
14| BH5.60.110| Hollow bolt 16| 2
15| GB/T91-2000| Cotter pin 5×40| 2
16| 5G24.01.102| Pin| 2
17| SG24.01.017| Hydraulic cylinder| 1
18| 5G24.01.103| Sleeve| 2
19| BH5.60.108| Ball adapter| 4
20| JB/T 982-1977| Casket 14| 4
21| MK6| Throttle valve| 2
22| BH5.60.109| Adapter 14-14| 2
23| SG24.01.018| Hose| 2
NO. | PART NO. | Name & Specifications | Quantity |
---|---|---|---|
1 | GB / T5783-2000 | Bolt M8x20 | 7 |
2 | GB/ T93-1987 | Spring washer 8 | 7 |
3 | GB / T97. 1-2002 | Plain washer 8 | 7 |
4 | SG24.02.011 | Pin weldment | 1 |
5 | JB/T7940.1-1995 | Oil cup M8 | 1 |
6 | SG24.02.012 | Carbide tooth weldment | 36 (SG24) |
54 (SG24-PRO)
7| SG24.02.013| Housing weldment| 1
8| SG24.02.014| Grinder wheel weldment, SG24| 1
SG24-PRO.02.014| Grinder wheel weldment, SG24-PRO| 1
g| GB/T6178-1986| Slotted nut M24| 1
10| SG24.02.015| Wheel guard weldment| 1
11| SG24.02.016| Guard weldment| 1
12| SG24.02.101| Sleeve| 2
13| GB / T96.2-2002| Plain washer 12| 2
14| GB/ T93-1987| Spring washer 12| 2
15| GB / T5783-2000| Bolt M12x35| 2
16| GB / T5783-2000| Bolt M10x25| 12
17| GB/ T93-1987| Spring washer 10| 12
18| GB / T97. 1-2002| Plain washer 10| 12
19| GB / T889. 1-2000| Lock nut M16| 4
20| GB/ T93-1987| Spring washer 14| 36 (SG24)
54 (SG24-PRO)
21| GB / T6171-2000| Nut M14*1.5| 36 (SG24)
54 (SG24-PRO)
22| SG24.02.018| Pin| 2
23| SG24.02.017| Lid, shield| 1
24| GB / T5783-2000| Bolt M16x50| 4
25| XHSO.169Z.01L| Gearbox assembly (1: 1.77)| 1
Name:__
Address:__
City State Zip:
Phone:
E-mail:
Model Number:____
Serial Number:__
Purchased From:
Purchase Date:_____
Item No. | Description | Qty | Price | Amount |
---|---|---|---|---|
Comments:
FARMER-HELPER
Limited Warranty
Unless otherwise stated on purchase invoice, Betstco warrants to original
Purchaser that Farmer-Helper products are free from major deffects in material
under normal use and service for a period of 90 Days from the date the product
is purchased or shipped, whichever is later. Commercial use 90 days. Use at
address that is not yours, is considered commercial use. Consumable,
Expendalble, Wear Items (Rubber plastic parts, hydraulic hoses, belts, tires,
cables, blades, tines, wedges, teeth, tiups, chains, pins, brushes, filters,
etc) and cracked hydraulic pumps, bent or broken cylinder rods are not covered
under this warran- ty. Warranty does not cover items that have been modified,
damaged by abuse or usage not in accor- dance with design or maintenance.
Betstco obligation under this warranty is to repair or replace defective upon
approval by; Betstco, 83371 Melton Rd. N, Creswell OR 97426 that Warranty
Claim is valid. Product shall be returned upon request of Betstco.
Transportation charges to be prepaid by user.
Gasoline or diesel engines used to powered Farmer-Helper products are covered
by the warranty of the appropriate engine manufacturean Purchaser must look to
the engine manufacture for all issues relating to engine operation.
Betstco assumes no responsibility for outside labor.
PERMISSABLE BY APPLICABLE LAW, BETSTCO HEREBY DISCLAIMS ALL WARRANTIES OF ANY
KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, ANY IMPLIED WARRANTIES WITH
RESPECT TO THE PRODUCT PURCHASED, WITHOUT LIMITING THE GENERALITY OF THE
FOREGOING, BETSTCO HEREBY EXPRESSLY DISCLAIMS ALL LIABILITY FOR PRODUCT DEFECT
OR FAILURE, CLAIMS THAT ARE DUE TO NORMAL WEAR, PRODUCT MISUSE, ABUSE, PRODUCT
MODIFICATION, IMPROPER PROD-UCT SELECTION, NON-COMPLIANCE WITH ANY CODES, OR
ISAPPROPRIATION. BETSTCO MAKES NO WARRANTIES TO THOSE DEFINED AS “CONSUMERS”
IN THE MAGNUSON-MOSS WARRANTY FEDERAL TRADE COMMISION IMPROVEMENTS ACT. THE
FOREGOING EXCLUSION OF IMPLIED WARRANTIES DO NOT APPLY TO THE EXTENT
PROHIBITED BY LAW. PLEASE REFER TO YOUR LOCAL LAWS FOR ANY SUCH PROHIBITIONS.
THERE SHALL BE NO LIABILITY FOR PRODUCT LIABILITY OR LIABILITY ON THE PART OF
BETSTCO FOR ANY GENERAL SPECIAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE
SALE OR USE OF ANY PRODUCTS SOLD BY BETSTCO OR AN AGENT THEREOF, BETSTCO
MAKES NO WARRANTIES, EXPRESS OR IMPLIED, (INCLUDING, BUT NOT LIMITED TO, ANY
WARRANTY OF MERCHANTABILITY OR FITNESS OF THE PRODUCTS FOR ANY PURPOSE) WITH
RESPECT TO THE PRODUCTS COVERED BY THIS AGREEMENT EXCEPT AS IN THIS PARAGRAPH
OTHERWISE EXPRESSLY PROVIDED. THIS IS THE SOLE AND ONLY WARRANTY OF VALUE-
LEADER PRODUCTS, NO OTHER WARRANTY IS APPLICABLE, EITHE EXPRESSED OR IMPLIED,
IN FACT BY LAW.
This warranty shall not be interpreted to render Betstco, or any authorized
agent liable for injury or damages of any kind or nature, direct,
consequential, or contingent, to a person or property.
The sole and only remedy in regard to any defective product shall be the
repair or replacement thereof as herein provided, Betstco, agent(s) of Betstco
shall not be liable for any consequential, special, incidental or punitive
damages resulting from or caused by any such defects Betstco reserves the
rights to make improvements in design or changes in specifacations at any
time, without incurring any obligations to owners of the units previously
sold.
WARRANTY VOID IF REGISTRATION IS NOT RECEIVED OR RECORDED ONLINE WITHIN 30 DAYS OF PURCHASE DATE OR SHIP DATE, WHICHEVER IS LATER.
ITEM:__ MODEL#__ PURCHASE DATE:__//
PURCHASED FROM: GIFT INV# ORDER#
OWNER NAME:____SERIAL #____
OWNER ADDRESS:__
CTy:__COUNTY:ST:ZIP:
PHONE:_____EMAIL:____
ACCEPTANCE OF RESPONSIBILITY:
| (PURCHASER) HAVE READ OPERATORS MANUAL AND LIMITED WARRANTY OR SOMEONE HAS
READ/AND EXPLAINED ALL INSTRUCTIONS TO ME. | UNDERSTAND THIS WARRANTY DOES NOT
COVER ANY LABOR AND THAT ALL DISPUTES WILL BE SETTLED BY BINDING ARBITRATION.
BIND-ING ARBITRATION IS CONDUCTED BY THE BETTER BUSINESS BUREAU (BBB) LOCATED
AT 4004 SW KRUSE WAY PLACE ST 375 LAKE OSWEGO OR 97035 OR THE CURRENT BBB
LOCATION CLOS-EST TO BETSTCO.
| ACKNOWLEDGE MY LIMITED WARRANTY IS VOID IF ANY ATTEMPT TO REPAIR OR REPLACE
DEFECTIVE PARTS HAS BEEN MADE BY UNAUTHORIZED PERSONNEL.I ACKNOWL-EDGE RECEIPT
OF MY OPERATORS MANUAL AND HAVE READ THE SAFE OPERATION SECTION.
| ACKNOWLEDGE UNDERSTANDING MAINTENANCE AND SAFE OPERATION REQUIREMENTS, ITEM
SPECIFACATIONS, OPERATION, CONTROLS AND STORAGE REQUIRMENTS. | UNDERSTAND THAT
IS ALONE AM RESPONSIBLE FOR PROPER MAINTENANCE, CARE AND SAFE OPERATIONOF THIS
FARMER-HELPER ITEM | (PURCHASER) AGREE THAT PERSONS NOT FAMILIAR WITH THE
OPERATION OF THIS ITEM SHOULD NOT BE ALLOWED TO USE IT. CHILDREN ESPECIALLY
SHOULD NOT OPERATE OR BE NEAR POWER PRODUCTS WHEN IN USE. ANYONE OPERATING
VALUE-LEADER PRODUCTS SHOULD HAVE READ OPERATIONS MANUALS AND SAFTEY MANUALS.
OWNERS SIGNATURE: x____DATE:__//__
‘YOU MUST SIGN THIS WARRANTY AND MAIL OR FAX A COPY TO BETSTCO, 83371 MELTON
RD, CRESWELL OR, 97426. IF YOU PREFER YOU MAY COMPLETE YOUR REGISTRATION
ONLINE AT WWW.VALUE-LEADER.COM. THIS WARRANTY
IS NOT EFFECTIVE UNLESS PURCHASER COMPLETE REGISTRATION AND WARRANTY FOR
WITHIN 30 DAYS OF PURCHASE OR SHIP DATE WHICHEVER IS LATER.
NOTE: WE MAY REFUSE WARRANTY OF ANY KIND UNLESS BETSTCO, RECEIVES A
COMPLETED, LEGIBLE AND SIGNED WARRANTY REGISTRATION. IT IS THE RESPONSIBILITY
OF THE PURCHASER TO ASSURE THAT REGISTRATION DOCUMENT IS RECIEVED BY
1 YEAR EXTENDED WARRANTY & REGISTRATION
FARMER-HELPER IMPLEMENTS
BRANDED PRODUCTS
1 YEAR EXTENDED WARRANTY
1 Year Extended Warranty amends to original Recorded Warranty Registration the
time period of described coverage. Extended Warranty does not apply to
consumable and Expendable Item as described in Product Warranty Registra-tion.
This amendment does not affect any other part of recorded Warranty Regis-
tration or policy.
No one is authorized to alter, modify, or enlarge this Amendment to original
recorded Warranty Registration
EXTENDED REGISTRATION & PAYMENT MUST BE RECEIVED WITHIN 30 DAYS OF PURCHASE
DATE
EXTENDED WARRANTY REGISTRATION
PRODUCT & MODEL #____
SERIAL #____
OWNER NAME:__
BETSTCO INVOICE #____
ACCEPTANCE OF RESPONSIBILITY:
| (PURCHASER) HAVE READ AND UNDERSTAND THE EXTENDED WARRANTY OR SOMEONE HAS
READ AND EXPLAINED ALL THE ABOVE TO ME.
| UNDERSTAND THIS EXTENDED WARRANTY DOES NOT COVER ANY LABOR. | HAVE FILED MY
ORIGINAL WARRANTY REGISTRATION AND FULLY UNDERSTAND MY REQUIREMENTS. |
UNDERSTAND THAT | ALONE AM RESPONSIBLE FOR PROPER MAINTENANCE, CARE AND SAFE
OPERATION OF THIS TRACTOR IMPLEMENT.
OWNERS SIGNATURE: x FAX TO
1-541-895-2756DATE: //___
YOU MUST SIGN THIS WARRANTY AND MAIL OR FAX A COPY TO BETSTCO, 83371 MELTON
RD, CRESWELL OR. IF YOU PREFER YOU MAY COMPLETE YOUR REGISTRATION ONLINE AT
WWW.VALUE-LEADER.COM. THIS WARRANTY IS NOT
EFFECTIVE UNLESS PURCHASER COMPLETE REGISTRATION AND WARRANTY FOR WITHIN 30
DAYS OF PURCHASE OR SHIP DATE WHICHEVER IS LATER.
NOTE: WE MAY REFUSE WARRANTY OF ANY KIND UNLESS BETSTCO, RECEIVES A
COMPLETED, LEGIBLE AND SIGNED WARRANTY REGISTRATION. IT IS THE RESPONSIBILITY
OF THE PURCHASER TO ASSURE THAT REGISTRATION DOCUMENT IS RECIEVED BY BETSTCO.
www.Betstco.com
541-895-3083 M-F 7am-4pm PST
1aas 83371 Melton Rd, Creswell OR 97426
References
- Betstco Tractor Impliments
- 541-895-3083 M-F, 7am-4pm PST" class="nturl" > Value-Leader – Sales, Suport, and Service 541-895-3083 M-F, 7am-4pm PST
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>