makita RP001G Cordless Router Instruction Manual

: July 27, 2024
: Makita

Table of Contents

makita RP001G Cordless Router
SPECIFICATIONS
FAQs
SPECIFICATIONS
Symbols
Intended use
SAFETY WARNINGS
FUNCTIONAL DESCRIPTION
Electronic function
ASSEMBLY
OPERATION
General operation
WIRELESS ACTIVATION FUNCTION
Troubleshooting
MAINTENANCE
OPTIONAL ACCESSORIES
Read User Manual Online (PDF format)
Download This Manual (PDF format)

makita RP001G Cordless Router

makita-RP001G-Cordless-Router-PRODUCT

SPECIFICATIONS

Model: RP001G
Collet chuck capacity: 12 mm or 1/2″
Plunge capacity: 0 – 60 mm
No load speed: 8,000 – 25,000 min-1
Overall height with BL4040: 294 mm
Rated voltage: D.C. 36 V – 40 V max
Net weight: 4.0 – 5.2 kg
Applicable battery cartridge and charger:
- Battery cartridge: BL4020 / BL4025 / BL4040 / BL4040F / BL4050F / BL4080F (Recommended battery)
- Charger: DC40RA / DC40RB / DC40RC / DC40WA

FAQs

What type of materials can be used with the cordless router?

The cordless router is suitable for flush trimming and profiling of wood, plastic, and similar materials.

Can I use any battery cartridge and charger with the cordless router?

No, only use the recommended battery cartridges (BL4020, BL4025, BL4040, BL4040F, BL4050F, or BL4080F) and chargers (DC40RA, DC40RB, C40RC, DC40WA) listed in the manual to prevent injury or fire.

What should I do to minimize noise exposure while using the cordless router?

Wear ear protection as the noise emission during operation may differ from the declared value depending on the workpiece being processed.

How can I protect myself from excessive vibration when using the cordless router?

Identify safety measures based on an estimation of exposure in the actual conditions of use to minimize the impact of vibration. Be aware of all parts of the operating cycle to reduce vibration-related risks.

SPECIFICATIONS

Model:	RP001G
Collet chuck capacity	12 mm or 1/2″
Plunge capacity	0 – 60 mm
No load speed	8,000 – 25,000 min-1
Overall height	with BL4040
Rated voltage	D.C. 36 V – 40 V max
Net weight	4.0 – 5.2 kg

Due to our continuing program of research and development, the specifications herein are subject to change without notice.
Specifications and battery cartridges may differ from country to country.
The weight may differ depending on the attachment(s), including the battery cartridge. The lightest and heaviest combinations, according to EPTA-Procedure 01/2014, are shown in the table.

Applicable battery cartridge and charger

Battery cartridge| BL4020 / BL4025 / BL4040 / BL4040F / BL4050F* / BL4080F

: Recommended battery
---|---
Charger| DC40RA / DC40RB / DC40RC / DC40WA
- Some of the battery cartridges and chargers listed above may not be available depending on your region of residence.
- WARNING: Only use the battery cartridges and chargers listed above. Use of any other battery cartridges and chargers may cause injury and/or fire.

Symbols

The followings show the symbols that may be used for the equipment. Be sure that you understand their meaning before use.

$makita-RP001G-Cordless-Router-FIG-1 $1$$

Intended use

The tool is intended for flush trimming and profiling of wood, plastic, and similar materials.

Noise

The typical A-weighted noise level determined according to EN62841-2-17:
Sound pressure level (LpA): 92 dB (A)
Sound power level (LWA): 100 dB (A)
Uncertainty (K): 3 dB (A)
NOTE: The declared noise emission value(s) has been measured following a standard test method and may be used for comparing one tool with another.
NOTE: The declared noise emission value(s) may also be used in a preliminary assessment of exposure.
WARNING: Wear ear protection.
WARNING: The noise emission during the actual use of the power tool can differ from the declared value(s) depending on how the tool is used especially what kind of workpiece is processed.
WARNING: Be sure to identify safety measures to protect the operator that are based on an estimation of exposure in the actual conditions of use (taking account of all parts of the operating cycle such as the times when the tool is switched off and when it is running idle in addition to the trigger time).

Vibration

The vibration total value (tri-axial vector sum) determined according to EN62841-2-17:

Work mode: cutting grooves in MDF
Vibration emission (ah): 6.3 m/s2
Uncertainty (K) : 1.5 m/s2
NOTE: The declared vibration total value(s) has been measured under a standard test method and may be used for comparing one tool with another.
NOTE: The declared vibration total value(s) may also be used in a preliminary assessment of exposure.
WARNING: The vibration emission during the actual use of the power tool can differ from the declared value(s) depending on the ways in which the tool is used especially what kind of workpiece is processed.
WARNING: Be sure to identify safety measures to protect the operator that are based on an estimation of exposure in the actual conditions of use (taking account of all parts of the operating cycle such as the times when the tool is switched off and when it is running idle in addition to the trigger time).

Declarations of Conformity

For European countries only: The Declarations of conformity are included in Annex A to this instruction manual.

SAFETY WARNINGS

General power tool safety warnings
WARNING Read all safety warnings, instructions, illustrations, and specifications provided with this power tool. Failure to follow all instructions listed below may result in electric shock, fire, and/or serious injury.

Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.

Work area safety

Keep the work area clean and well-lit. Cluttered or dark areas invite accidents.
Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks that may ignite the dust or fumes.
Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.

Electrical safety

Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce the risk of electric shock.
Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges, and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.
Do not abuse the cord. Never use the cord for carrying, pulling, or unplugging the power tool. Keep the cord away from heat, oil, sharp edges, or moving parts. Damaged or entangled cords increase the risk of electric shock.
When operating a power tool outdoors, use an extension cord suitable for outdoor use. The use of a cord suitable for outdoor use reduces the risk of electric shock.
If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply. The use of an RCD reduces the risk of electric shock.
Power tools can produce electromagnetic fields (EMF) that are not harmful to the user. However, users of pacemakers and other similar medical devices should contact the maker of their device and/or doctor for advice before operating this power tool.

Personal safety

Stay alert, watch what you are doing, and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol, or medication. A moment of inattention while operating power tools may result in serious personal injury.
Use personal protective equipment. Always wear eye protection. Protective equipment such as a dust mask, non-skid safety shoes, hard hats, or hearing protection used for appropriate conditions will reduce personal injuries.
Prevent unintentional starting. Ensure the switch is in the off-position before connecting to a power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energizing power tools that have the switch on invites accidents.
Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.
Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
Dress properly. Do not wear loose clothing or jewelry. Keep your hair and clothing away from moving parts. Loose clothes, jewelry, or long hair can be caught in moving parts.
If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. The use of dust collection can reduce dust-related hazards.
Do not let familiarity gained from the frequent use of tools allow you to become complacent and ignore tool safety principles. A careless action can cause severe injury within a fraction of a second.
Always wear protective goggles to protect your eyes from injury when using power tools. The goggles must comply with ANSI Z87.1 in the USA, EN 166 in Europe, or AS/NZS 1336 in Australia/New Zealand. In Australia/New Zealand, it is legally required to wear a face shield to protect your face, too.
- It is an employer’s responsibility to enforce the use of appropriate safety protective equipment by the tool operators and by other persons in the immediate working area.

Power tool use and care

Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed.
Do not use the power tool if the switch does not turn on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
Disconnect the plug from the power source and/or remove the battery pack, if detachable, from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.
Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.
Maintain power tools and accessories. Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.
Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.
Use the power tool, accessories tool bits, etc. under these instructions, taking into account the working conditions andthe work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.
Keep handles and grasping surfaces dry, clean, and free from oil and grease. Slippery handles and grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.
When using the tool, do not wear cloth work gloves which may be entangled. The entanglement of cloth work gloves in the moving parts may result in personal injury.

Battery tool use and care

Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack.
Use power tools only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire.
When the battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws, or other small metal objects, that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire.
Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts the eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns.
Do not use a battery pack or tool that is damaged or modified. Damaged or modified batteries may exhibit unpredictable behavior resulting in fire, explosion, or risk of injury.
Do not expose a battery pack or tool to fire or excessive temperature. Exposure to fire or temperature above 130 °C may cause an explosion.
Follow all charging instructions and do not charge the battery pack or tool outside the temperature range specified in the instructions. Charging improperly or at temperatures outside the specified range may damage the battery and increase the risk of fire.

Service

Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.
Never service damaged battery packs. Service of battery packs should only be performed by the manufacturer or authorized service providers.
Follow instructions for lubricating and changing accessories.

Cordless router safety warnings

Hold the power tool by insulated gripping surfaces only, because the cutter may contact hidden wiring. Cutting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock.
Use clamps or another practical way to secure and support the workpiece to a stable platform. Holding the work by your hand or against the body leaves it unstable and may lead to loss of control.
Use only router bits with the correct shank diameter that matches the designed collet chuck.
Use only router bits that are rated at least equal to the maximum speed marked on the tool. If the tool has a variable speed control function, set the tool speed under the speed rating of the router bit.
Handle the router bits very carefully.
Check the router bit carefully for cracks or damage before operation. Replace cracked or damaged router bit immediately.
Avoid cutting nails. Inspect for and remove all nails from the workpiece before operation.
Hold the tool firmly.
Keep hands away from rotating parts.
Make sure the router bit is not contacting the workpiece before the switch is turned on.
Before using the tool on an actual workpiece, let it run for a while. Watch for vibration or wobbling that could indicate an improperly installed router bit.
Make sure the router bit rotates the direction and the feed direction.
Do not leave the tool running. Operate the tool only when hand-held.
Always switch off and wait for the router bit to come to a complete stop before removing the tool from the workpiece.
Do not touch the router bit immediately after operation; it may be extremely hot and could burn your skin.
Do not smear the base carelessly with thinner, gasoline, oil, or the like. They may cause cracks in the base.
Some materials contain chemicals that may be toxic. Take caution to prevent dust inhalation and skin contact. Follow material supplier safety data.
Wear hearing protection during extended periods of operation.
Always use the correct dust mask/respirator for the material and application you are working with.

SAVE THESE INSTRUCTIONS.

WARNING: DO NOT let comfort or familiarity with the product (gained from repeated use) replace strict adherence to safety rules for the subject product. MISUSE or failure to follow the safety rules stated in this instruction manual may cause serious personal injury.

Important safety instructions for battery cartridge

Before using the battery cartridge, read all instructions and cautionary markings on (1) the battery charger, (2) the battery, and (3) the product using the battery.
Do not disassemble or tamper with the battery cartridge. It may result in a fire, excessive heat, or explosion.
If operating time has become excessively shorter, stop operating immediately. It may result in a risk of overheating, possible burns, and even an explosion.
If electrolyte gets into your eyes, rinse them out with clear water and seek medical attention right away. It may result in loss of your eyesight.
Do not short the battery cartridge:
Do not touch the terminals with any conductive material.
Avoid storing battery cartridges in a container with other metal objects such as nails, coins, etc.
Do not expose the battery cartridge to water or rain. A battery short can cause a large current flow, overheating, possible burns, and even a breakdown.
Do not store and use the tool and battery cartridge in locations where the temperature may reach or exceed 50 °C (122 °F).
Do not incinerate the battery cartridge even if it is severely damaged or is completely worn out. The battery cartridge can explode in a fire.
Do not nail, cut, crush, throw, drop the battery cartridge, or hit against a hard object to the battery cartridge. Such conduct may result in a fire, excessive heat, or explosion.
Do not use a damaged battery.
The contained lithium-ion batteries are subject to the Dangerous Goods Legislation requirements. For commercial transports e.g. by third parties, and forwarding agents, special requirements on packaging and labeling must be observed. For preparation of the item being shipped, consulting an expert for hazardous material is required. Please also observe possibly more detailed national regulations. Tape or mask off open contacts and pack up the battery in such a manner that it cannot move around in the packaging.
When disposing of the battery cartridge, remove it from the tool and dispose of it in a safe place. Follow your local regulations relating to the disposal of batteries.
Use the batteries only with the products specified by Makita. Installing the batteries to non-compliant products may result in a fire, excessive heat, explosion, or leak of electrolyte.
If the tool is not used for a long period, the battery must be removed from the tool.
During and after use, the battery cartridge may take on heat which can cause burns or low temperature burns. Pay attention to the handling of hot battery cartridges.
Do not touch the terminal of the tool immediately after use as it may get hot enough to cause burns.
Do not allow chips, dust, or soil to stick into the terminals, holes, and grooves of the battery cartridge. It may cause heating, catching fire, burst, and malfunction of the tool or battery cartridge, resulting in burns or personal injury.
Unless the tool supports the use near high-voltage electrical power lines, do not use the battery cartridge near high-voltage electrical power lines. It may result in a malfunction or breakdown of the tool or battery cartridge.
Keep the battery away from children. SAVE THESE INSTRUCTIONS.

CAUTION: Only use genuine Makita batteries. Use of non-genuine Makita batteries, or batteries that have been altered, may result in the battery bursting causing fires, personal injury, and damage. It will also void the Makita warranty for the Makita tool and charger.

Tips for maintaining maximum battery life

Charge the battery cartridge before completely discharged. Always stop tool operation and charge the battery cartridge when you notice less tool power.
Never recharge a fully charged battery cartridge. Overcharging shortens the battery service life.
Charge the battery cartridge at room temperature at 10 °C – 40 °C (50 °F – 104 °F). Let a hot battery cartridge cool down before charging it.
When not using the battery cartridge, remove it from the tool or the charger.
Charge the battery cartridge if you do not use it for a long period (more than six months).

Important safety instructions for the wireless unit

Do not disassemble or tamper with the wireless unit.
Keep the wireless unit away from young children. If accidentally swallowed, seek medical attention immediately.
Use the wireless unit only with Makita tools.
Do not expose the wireless unit to rain or wet conditions.
Do not use the wireless unit in places where the temperature exceeds 50 °C (122 °F).
Do not operate the wireless unit in places where medical instruments, such as heart pacemakers are nearby.
Do not operate the wireless unit in places where automated devices are nearby. If operated, automated devices may develop malfunction or error.
Do not operate the wireless unit in places under high temperatures or places where static electricity or electrical noise could be generated.
The wireless unit can produce electromagnetic fields (EMF) but they are not harmful to the user.
The wireless unit is an accurate instrument. Be careful not to drop or strike the wireless unit.
Avoid touching the terminal of the wireless unit with bare hands or metallic materials.
Always remove the battery on the product when installing the wireless unit into it.
When opening the lid of the slot, avoid the place where dust and water may come into the slot. Always keep the inlet of the slot clean.
Always insert the wireless unit in the correct direction.
Do not press the wireless activation button on the wireless unit too hard and/or press the button with an object with a sharp edge.
Always close the lid of the slot when operating.
Do not remove the wireless unit from the slot while the power is being supplied to the tool. Doing so may cause a malfunction of the wireless unit.
Do not remove the sticker on the wireless unit.
Do not put any stickers on the wireless unit.
Do not leave the wireless unit in a place where static electricity or electrical noise could be generated.
Do not leave the wireless unit in a place subject to high heat, such as a car sitting in the sun.
Do not leave the wireless unit in a dusty or powdery place or in a place where corrosive gas could be generated.
Sudden change of the temperature may bedew the wireless unit. Do not use the wireless unit until the dew is completely dried.
When cleaning the wireless unit, gently wipe it with a dry soft cloth. Do not use benzine, thinner, conductive grease or the like.
When storing the wireless unit, keep it in the supplied case or a static-free container.
Do not insert any devices other than the Makita wireless unit into the slot on the tool.
Do not use the tool with the lid of the slot damaged. Water, dust, and dirt coming into the slot may cause malfunction.
Do not pull and/or twist the lid of the slot more than necessary. Restore the lid if it comes off from the tool.
Replace the lid of the slot if it is lost or damaged. SAVE THESE INSTRUCTIONS.

FUNCTIONAL DESCRIPTION

CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before adjusting or checking the function of the tool.
Installing or removing the battery cartridge

CAUTION: Always switch off the tool before installing or removing the battery cartridge.
CAUTION: Hold the tool and the battery cartridge firmly when installing or removing the battery cartridge. Failure to hold the tool and the battery cartridge firmly may cause them to slip off your hands and result in damage to the tool and battery cartridge and a personal injury.
To install the battery cartridge, align the tongue on the battery cartridge with the groove in the housing and slip it into place. Insert it until it locks in place with a little click. If you can see the red indicator as shown in the figure, it is not locked completely.
To remove the battery cartridge, slide it from the tool while sliding the button on the front of the cartridge.
CAUTION: Always install the battery cartridge fully until the red indicator cannot be seen. If not, it may accidentally fall out of the tool, causing injury to you or someone around you.
CAUTION: Do not install the battery cartridge forcibly. If the cartridge does not slide in easily, it is not being inserted correctly.

Indicating the remaining battery capacity

Press the check button on the battery cartridge to indicate the remaining battery capacity. The indicator lamps light up for a few seconds. $makita-RP001G-Cordless-Router-FIG-1 $4$$
NOTE: Depending on the conditions of use and the ambient temperature, the indication may differ slightly from the actual capacity.
NOTE: The first (far left) indicator lamp will blink when the battery protection system works.

Tool/battery protection system

The tool is equipped with a tool/battery protection system.
This system automatically cuts off power to the motor to extend tool and battery life. The tool will automatically stop during operation if the tool or battery is placed under one of the following conditions:

Overload protection

When the tool/battery is operated in a manner that causes it to draw an abnormally high current, the tool automatically stops. In this situation, turn the tool off and stop the application that caused the tool to become overloaded.
Then turn the tool on to restart.

Overheat protection

When the tool or battery is overheated, the tool stops automatically and lamps blink. In this case, turn off the tool by pressing the lock/unlock button, removing the battery, or leaving the tool for 60 seconds without any operation. Let the tool and battery cool before turning the tool on again.
Overdischarge protection
When the battery capacity is not enough, the tool stops automatically. In this case, remove the battery from the tool and charge the battery.
Protections against other causes
The protection system is also designed for other causes that could damage the tool and allows the tool to stop automatically. Take all the following steps to clear the causes, when the tool has been brought to a temporary halt or stop in operation.

Turn the tool off, and then turn it on again to restart.
Charge the battery(ies) or replace it/them with a recharged battery(ies).
Let the tool and battery(ies) cool down.

If no improvement can be found by restoring the protection system, then contact your local Makita Service Center.

Switch action

To turn on the tool, press the lock/unlock button. The tool turns into the standby mode. To start the tool, pull the switch trigger in the standby mode. To stop the tool, release the switch trigger and the tool turns into the standby mode.
To turn off the tool, press the lock/unlock button in the standby mode.
For continuous operation, pull the switch trigger and press the lock button. Pull the switch trigger again to cancel the continuous operation and release the switch trigger to stop the tool.
- NOTE: If the tool is left for 5 seconds without any operation in the standby mode or 5 seconds after releasing the switch trigger, the tool automatically turns off.

Lighting up the lamps

CAUTION: Do not look in the light or see the source of light directly.
NOTICE: When the tool is overheated, the lamp blinks. Cool down the tool fully before operating the tool again.
To turn on the lamps, press the lock/unlock button. The lamps keep on lighting during operation. The lamps go off when the tool is left for 5 seconds without any operation in the standby mode or 5 seconds after releasing the switch trigger.
NOTE: Use a dry cloth to wipe the dirt off the lens of the lamp. Be careful not to scratch the lens of the lamp, or it may lower the illumination.

Speed adjusting dial

The rotation speed of the tool can be changed by turning the speed-adjusting dial.
The table below shows the number on the dial and the corresponding rotation speed.

Number	Speed
1	8,000 min-1
2	12,500 min-1
Number	Speed
---	---
3	17,000 min-1
4	21,000 min-1
5	25,000 min-1

CAUTION: Do not change the rotation speed during operation. Otherwise unexpected reaction of the tool may cause an injury.
NOTICE: If the tool is operated continuously at low speed for a long time, the motor will get overloaded, resulting in tool malfunction.
NOTICE: The speed-adjusting dial can be turned only as far as 5 and back to 1. Do not force it past 5 or 1, or the speed-adjusting function may no longer work.

Electronic function

The tool is equipped with electronic functions for easy operation.

Constant speed control

The speed control function provides a constant rotation speed regardless of load conditions.

Soft start

The soft-start function minimizes start-up shock and makes the tool start smoothly.

Soft brake

The tool stops gently with the soft brake. The soft brake prevents damage to the workpiece due to recoil and allows you to start the next operation earlier.
If the tool consistently fails to stop the router bit after the switch is turned off, have the tool serviced at a Makita service center.

ASSEMBLY

CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before carrying out any work on the tool.

Installing or removing router bit

CAUTION: Install the router bit securely. Always use only the wrench provided with the tool. A loose or overtightened router bit can be dangerous.
CAUTION: Always use a collet cone which is suitable for the shank diameter of the router bit.
CAUTION: Do not tighten the collet nut without inserting a router bit or install a small shank router bit without using a collet sleeve. Either can lead to breakage of the collet cone.
CAUTION: Use only router bits of which the maximum speed, as indicated on the router bit, does exceed the maximum speed of the router.
Insert the router bit into the collet cone. Press the shaft lock and tighten the collet nut with the wrench.
When using the router bit with smaller shank diameter, first insert the appropriate collet sleeve into the collet cone, then install the router bit.
To remove the router bit, follow the installation procedure in reverse.

Installing or removing the chip deflector

CAUTION: Before operation, always make sure that the chip deflector is installed properly.
To install the chip deflector, insert the chip deflector into a groove, aligning the hole of the chip deflector with the protrusion.
To remove the chip deflector, tilt the upper part of the chip deflector forward and pull it out.

OPERATION

Adjusting the cutting depth
To adjust the cutting depth, release the lock lever, then lower the body. After the adjustment, turn the lock lever firmly to secure the body.

Adjusting cutting depth with the stopper screw

Place the tool on a flat surface.
Select the stopper screw by rotating the stopper base.
- To adjust the height of the stopper screws, use the wrench or driver.
Loosen the fixing nut, then pull up the stopper pole while pressing the feed button.
Release the lock lever, push down the tool until the tip of the router bit touches the flat surface, and then turn the lock lever to secure the tool.
Press down the stopper pole while pressing the feed button until it contacts the stopper screw.
Slide the depth pointer so that the pointer indicates “0” on the scale.
Adjust the cutting depth by pulling up the stopper pole while pressing the feed button.
To perform fine adjustment of the cutting depth, turn the dial on the stopper pole so that it indicates “0”.
Turn the head of the stopper pole to obtain the desired depth. To increase the depth, turn the head counterclockwise. To decrease the depth, turn the head clockwise. (The depth changes by 1 mm per one revolution.)
Tighten the fixing nut to secure the stopper pole.
Release the lock lever.

By pushing down the tool until the stopper pole meets the stopper screw, you can obtain the depth of cut which you adjusted by above procedure.

Adjusting the upper limit of the tool body

The upper limit of the tool body can be adjusted by turning the nylon nut.

CAUTION: Do not lower the nylon nut too low. The router bit will protrude dangerously.

General operation

CAUTION: Before operation, always make sure that the tool body automatically rises to the upper limit and the router bit does not protrude from the tool base when the lock lever is loosened.

Set the base on the workpiece to be cut without the router bit making any contact.
Turn the tool on and wait until the router bit attains full speed.
Lower the tool body and move the tool forward over the workpiece surface, keeping the base flush and advancing smoothly until the cutting is complete.
- When doing edge cutting, the workpiece surface should be on the left side of the router bit in the feed direction.
- When using the straight guide or the trimmer guide, be sure to keep it on the right side in the feed direction. This will help to keep it flush with the side of the workpiece.
- NOTE: Moving the tool forward too fast may cause a poor-quality of cut or damage to the router bit or motor. Moving the tool forward too slowly may burn and mar the cut.
- The proper feed rate will depend on the router bit size, the kind of workpiece, and the depth of cut.
- Before beginning the cut on the actual workpiece, make a sample cut on a piece of scrap lumber to consider the appropriate feed speed.
- You can also confirm the router bit set by measuring the sample cut.

Using the straight guide

The straight guide is effectively used for straight cuts when chamfering or grooving.

Remove the clamping screw and the washer from the guide holder.
Loosen the adjusting screw to make a groove. Fit the straight guide into the groove, then mount the washer and tighten the clamping screw.
Mount rod 8 to the slots in the guide holder and tighten the clamping screws.
Install the straight guide to the slots in the tool base, and then tighten the clamping screws.
Loosen the clamping screw and adjust the distance between the router bit and the straight guide by turning the adjusting screw (1.5 mm per turn). At the desired distance, tighten the clamping screw to secure the straight guide.
Move the tool with the straight guide flush with the side of the workpiece.
- Wider straight guide of desired dimensions may be made by using the convenient holes in the guide to bolt on extra pieces of wood.
- If the distance (A) between the side of the workpiece and the cutting position is too wide for the straight guide, or if the side of the workpiece is not straight, the straight guide cannot be used.
- In this case, firmly clamp a straight board to the workpiece and use it as a guide against the base. Feed the tool in the direction of the arrow.

Using the fine adjusting straight guide

Optional accessory
The fine-adjusting straight guide can adjust the distance more accurately than the straight guide.

Mount rod 8 to the slots in the guide holder and tighten the thumb screw (M5 x 14 mm).
Install the fine-adjusting straight guide to the tool base. Tighten the clamping screws on the tool base.
Loosen the thumb screw (M6 x 50 mm) and adjust the distance between the router bit and the straight guide by turning the adjusting screw (1 mm per turn). At the desired distance, tighten the thumb screw (M6 x 50 mm) to secure the straight guide. The scale ring can be rotated separately from the adjusting screw, so scale unit can be aligned to zero (0).

Adjusting guide shoe width
Guide shoe is adjustable in the range from 280 mm to 350 mm.

Loosen the screws and move the guide shoe width to adjust.
After adjusting the width, tighten the screws.
- Minimum opening width
- Maximum opening width

Using the templet guide

The templet guide allows for repetitive cuts with temple patterns by using a templet.

Loosen the screws on the tool base and remove them.
Place the templet guide on the base, and then tighten the screws.
Place the tool on the templet and move the tool so that the templet guide slides along the side of the templet.
- NOTE: The workpiece will be cut a slightly different size from the templet. Allow for the distance (X) between the router bit and the outside of the temple guide. The distance (X) can be calculated by using the following equation: Distance (X) = (outside diameter of the templet guide – router bit diameter) / 2

Using the trimmer guide

Optional accessory
The trimmer guide allows for trimming the curved side like veneers for furniture by moving the guide roller along the side of the workpiece.

Install the trimmer guide and rods to the guide holder.
Insert rods into the slots in the guide holder and tighten the clamping screw.
Loosen the clamping screw and adjust the distance between the router bit and the trimmer guide by turning the adjusting screw (1.5 mm per turn). At the desired distance, tighten the clamping screw to secure the trimmer guide.
Move the tool with the guide roller riding the side of the workpiece.

Dust nozzle
Installing the dust nozzle enables to connection of a Makita vacuum cleaner to the tool.

Install the dust nozzle on the tool base using the thumb screw so that protrusion on the dust nozzle fits the notch in the tool base.
Connect a Makita vacuum cleaner to the dust nozzle.

WIRELESS ACTIVATION FUNCTION

What you can do with the wireless activation function

The wireless activation function enables clean and comfortable operation. By connecting a supported vacuum cleaner to the tool, you can run the vacuum cleaner automatically along with the switch operation of the tool.

To use the wireless activation function, prepare following items:

A wireless unit (optional accessory)
A vacuum cleaner which supports the wireless activation function

The overview of the wireless activation function setting is as follows. Refer to each section for detail procedures.

Installing the wireless unit
Tool registration for the vacuum cleaner
Starting the wireless activation function

Installing the wireless unit Optional accessory

CAUTION: Place the tool on a flat and stable surface when installing the wireless unit.
NOTICE: Clean the dust and dirt on the tool before installing the wireless unit. Dust or dirt may cause malfunction if it comes into the slot of the wireless unit.
NOTICE: To prevent the malfunction caused by static, touch a static discharging material, such as a metal part of the tool, before picking up the wireless unit.
NOTICE: When installing the wireless unit, always be sure that the wireless unit is inserted in the correct direction and the lid is completely closed.

Open the lid on the tool as shown in the figure.
Insert the wireless unit to the slot and then close the lid.
- When inserting the wireless unit, align the projections with the recessed portions on the slot.
- When removing the wireless unit, open the lid slowly.
- The hooks on the back of the lid will lift the wireless unit as you pull up the lid.
- After removing the wireless unit, keep it in the supplied case or a static-free container.
- NOTICE: Always use the hooks on the back of the lid when removing the wireless unit. If the hooks do not catch the wireless unit, close the lid completely and open it slowly again.

Tool registration for the vacuum cleaner

NOTE: A Makita vacuum cleaner supporting the wireless activation function is required for the tool registration.
NOTE: Finish installing the wireless unit to the tool before starting the tool registration.
NOTE: During the tool registration, do not pull the switch trigger or turn on the power switch on the vacuum cleaner.
NOTE: Refer to the instruction manual of the vacuum cleaner, too.

If you wish to activate the vacuum cleaner along with the switch operation of the tool, finish the tool registration beforehand.

Install the batteries to the vacuum cleaner and the tool.
Set the standby switch on the vacuum cleaner to “AUTO”.
Press the wireless activation button on the vacuum cleaner for 3 seconds until the wireless activation lamp blinks in green. And then press the wireless activation button on the tool in the same way.

If the vacuum cleaner and the tool are linked successfully, the wireless activation lamps will light up in green for 2 seconds and start blinking in blue.

NOTE: The wireless activation lamps finish blinking in green after 20 seconds elapsed. Press the wireless activation button on the tool while the wireless activation lamp on the cleaner is blinking. If the wireless activation lamp does not blink in green, push the wireless activation button briefly and hold it down again.
NOTE: When performing two or more tool registrations for one vacuum cleaner, finish the tool registrations one by one.

Starting the wireless activation function

NOTE: Finish the tool registration for the vacuum cleaner before the wireless activation.
NOTE: Refer to the instruction manual of the vacuum cleaner, too.

After registering a tool to the vacuum cleaner, the vacuum cleaner will automatically run along with the switch operation of the tool.

Install the wireless unit to the tool.
Connect the hose of the vacuum cleaner with the tool.
Set the standby switch on the vacuum cleaner to “AUTO”.
Push the wireless activation button on the tool briefly. The wireless activation lamp will blink in blue.
Turn on the tool. Check if the vacuum cleaner runs while the tool is operating. To stop the wireless activation of the vacuum cleaner, push the wireless activation button on the tool.
- NOTE: The wireless activation lamp on the tool will stop blinking in blue when there is no operation for 2 hours. In this case, set the stand-by switch on the vacuum cleaner to “AUTO” and push the wireless activation button on the tool again.
- NOTE: The vacuum cleaner starts/stops with a delay. There is a time lag when the vacuum cleaner detects a switch operation of the tool.
- NOTE: The transmission distance of the wireless unit may vary depending on the location and surrounding circumstances.
- NOTE: When two or more tools are registered to one vacuum cleaner, the vacuum cleaner may start running even if you do not turn on your tool because another user is using the wireless activation function.

Description of the wireless activation lamp status

The wireless activation lamp shows the status of the wireless activation function. Refer to the table below for the meaning of the lamp status.

$makita-RP001G-Cordless-Router-FIG-1 $57$$

Cancelling tool registration for the vacuum cleaner

Perform the following procedure when canceling the tool registration for the vacuum cleaner.

Install the batteries to the vacuum cleaner and the tool.
Set the standby switch on the vacuum cleaner to “AUTO”.
Press the wireless activation button on the vacuum cleaner for 6 seconds. The wireless activation lamp blinks in green and then becomes red. After that, press the wireless activation button on the tool in the same way.
- If the cancellation is performed successfully, the wireless activation lamps will light up in red for 2 seconds and start blinking in blue.
- NOTE: The wireless activation lamps finish blinking in red after 20 seconds elapsed. Press the wireless activation button on the tool while the wireless activation lamp on the cleaner is blinking. If the wireless activation lamp does not blink in red, push the wireless activation button briefly and hold it down again.

Troubleshooting

Troubleshooting for wireless activation function

Before asking for repairs, conduct your own inspection first. If you find a problem that is not explained in the manual, do not attempt to dismantle the tool. Instead, ask Makita Authorized Service Centers, always using Makita replacement parts for repairs.

State of abnormality| Probable cause (malfunction)| Remedy
---|---|---
The wireless activation lamp does not light/blink.| The wireless unit is not installed into the tool. The wireless unit is improperly installed into the tool.| Install the wireless unit correctly.
The terminal of the wireless unit and/or the slot is dirty.| Gently wipe off dust and dirt on the terminal of the

wireless unit and clean the slot.

The wireless activation button on the tool has not been pushed.| Push the wireless activation button on the tool

briefly.

The standby switch on the vacuum cleaner is not set to “AUTO”.| Set the stand- by switch on the vacuum cleaner to “AUTO”.
No power supply| Supply the power to the tool and the vacuum cleaner.
Cannot finish tool registration / can- celling tool registration successfully.| The wireless unit is not installed into the tool. The wireless unit is improperly installed into the tool.| Install the wireless unit correctly.
The terminal of the wireless unit and/or the slot is dirty.| Gently wipe off dust and dirt on the terminal of the

wireless unit and clean the slot.

The stand-by switch on the vacuum cleaner is not set to “AUTO”.| Set the standby switch on the vacuum cleaner to “AUTO”.
No power supply| Supply the power to the tool and the vacuum cleaner.
Incorrect operation| Push the wireless activation button briefly and perform the tool registration/cancellation procedures again.
The tool and vacuum cleaner are away from each other (out of the transmission range).| Get the tool and vacuum cleaner closer to each other. The maximum transmission distance is approximately 10 m however it may vary according to the circumstances.
Before finishing the tool registration/ cancellation; – the switch of the tool is turned on or; – the power button on the vacuum cleaner is turned on.| Push the wireless activation button briefly and perform the tool registration/cancellation procedures again.
The tool registration procedures for the tool or vacuum cleaner have not been finished.| Perform the tool registration procedures for both the tool and the vacuum cleaner at the same time.
Radio disturbance by other appliances which generate high-intensity radio waves.| Keep the tool and vacuum cleaner away from the appliances such as Wi- Fi devices and microwave ovens.
State of abnormality| Probable cause (malfunction)| Remedy
---|---|---
The vacuum cleaner does not run along with the switch operation of the tool.| The wireless unit is not installed into the tool.

The wireless unit is improperly installed into the tool.

| Install the wireless unit correctly.
The terminal of the wireless unit and/or the slot is dirty.| Gently wipe off dust and dirt on the terminal of the

wireless unit and clean the slot.

The wireless activation button on the tool has not been pushed.| Push the wireless activation button briefly and make

sure that the wireless activation lamp is blinking in blue.

The standby switch on the vacuum cleaner is not set to “AUTO”.| Set the standby switch on the vacuum cleaner to “AUTO”.
More than 10 tools are registered to the vacuum cleaner.| Perform the tool registration again.

If more than 10 tools are registered to the vacuum cleaner, the tool registered earliest will be canceled automatically.

The vacuum cleaner erased all tool registrations.| Perform the tool registration again.
No power supply| Supply the power to the tool and the vacuum cleaner.
The tool and vacuum cleaner are away from each other (out of the transmission range).| Get the tool and vacuum cleaner closer to each other. The maximum transmission distance is approximately 10 m however it may vary according to the circumstances.
Radio disturbance by other appliances which generate high-intensity radio waves.| Keep the tool and vacuum cleaner away from the appliances such as Wi- Fi devices and microwave ovens.
The vacuum cleaner runs while the tool is not operating.| Other users are using the wireless activation of the vacuum cleaner with their tools.| Turn off the wireless activation button of the other tools or cancel the tool registration of the other tools.

MAINTENANCE

CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection or maintenance.
NOTICE : Never use gasoline, benzine, thinner, alcohol, or the like. Discoloration, deformation, or cracks may result.
To maintain product SAFETY and RELIABILITY, repairs, and any other maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts.

ROUTER BITS

Optional accessory Straight bit $makita-RP001G-Cordless-Router-FIG-1 $61$$ $makita-RP001G-Cordless-Router-FIG-1 $62$$

OPTIONAL ACCESSORIES

CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose.

If you need any assistance with more details regarding these accessories, ask your local Makita Service Center.