D-Link DGS-1510-28X Smart Managed Gigabit Switches User Guide
- June 10, 2024
- D-Link
Table of Contents
DGS-1510-28X Smart Managed Gigabit Switches
Product Information
The DGS-1510-28X is a Layer 2+ SmartPro Stackable Switch with 24 10/100/1000Base-T Ports and 4 10GBase-X SFP+ Ports. It comes with a user’s guide CD, a multilingual getting started guide, a D-Link switch, a rack mounting bracket, rubber feet, a power cord, a power cord retainer, a console cable, and an accessory kit for one ground screw.
About This Guide
This guide provides step-by-step instructions for setting up the switch and includes information about warranty, safety, regulatory, and environment notices. Please note that the model you have purchased may appear slightly different from those shown in the illustrations.
Unpacking
Open the shipping carton and carefully unpack its contents. Please consult the packing list located in the User Guide to make sure all items are present and undamaged. If any item is missing or damaged, please contact your local D-Link reseller for replacement.
- One D-Link Switch
- Rack mounting bracket
- Rubber feet
- Power cord
- Power cord retainer
- Console cable
- User’s Guide CD with DNA (D-Link Network Assistant) program (optional)
- One multilingual Getting Started Guide
- An accessory kit for one ground screw
Switch Installation
For safe switch installation and operation, it is recommended that you:
- Visually inspect the power cord to see that it is secured fully to the AC power connector.
- Make sure that there is proper heat dissipation and adequate ventilation around the switch.
- Do not place heavy objects on the switch
Desktop or Shelf Installation
When installing the switch on a desktop or shelf, attach the rubber feet
included with the device on the bottom at each corner of the device’s base.
Allow enough ventilation space between the device and the objects around it.
Grounding the Switch
Before powering on your switch, you must connect it to ground. Refer to Figure
2 for instructions on how to connect a grounding cable.
This section describes how to connect the Switch to ground. You must complete
this procedure before powering on your Switch.
Required Tools and Equipment
-
Grounding screws (included in the accessory kit): One M4 x 6 mm (metric) pan-head screw
-
Grounding cable (not included in the accessory kit): The grounding cable should be sized according
to local and national installation requirements. Depending on the power supply and system, a 12 to 6 AWG copper conductor is required for installation. Commercially available 6 AWG wire is recommended. The length of the cable depends on the proximity of the Switch to proper grounding facilities. -
A screwdriver (not included in the accessory kit)
You can connect the Switch to a protective ground by following the steps below:
- Verify if the system power is off.
- Use the grounding cable to place the #8 terminal lug ring on top of the ground-screw opening.
- Insert the grounding screw into the ground-screw opening.
- Using a screwdriver, tighten the grounding screw to secure the grounding cable to the Switch.
- Attach the terminal lug ring at the other end of the grounding cable to an appropriate grounding stud or bolt on rack where the Switch is installed.
- Verify if the connections at the ground connector on the Switch and the rack are securely attached.
Installing Power Cord Retainer
To prevent accidental removal of the AC power cord, it is recommended to
install the power cord retainer together with the power cord.
- With the rough side facing down, insert the Tie Wrap into the hole below the power socket.
- Plug the AC power cord into the power socket of the Switch.
- Slide the Retainer through the Tie Wrap until the end of the cord.
- Circle the tie of the Retainer around the power cord and into the locker of the Retainer.
- Fasten the tie of the Retainer until the power cord is secured.
Rack Installation
The switch can be mounted in an EIA standard size 19-inch rack.
To install, attach the mounting brackets to the switch’s side panels (one on
each side) and secure them with the screws provided.
Then, use the screws provided with the equipment rack to mount
the switch in the rack.
Plugging in the AC Power Cord
You can now connect the AC power cord into the rear of the switch and to an
electrical outlet (preferably one that is grounded and surge protected).
Power Failure
As a precaution, the switch should be unplugged in case of power failure. When
power is resumed, plug the switch back in.
Product Usage Instructions
- Open the shipping carton and carefully unpack all contents.
- Consult the packing list located in the User Guide to ensure all items are present and undamaged. If any item is missing or damaged, contact your local D-Link reseller for replacement.
- Depending on your installation type, follow the instructions for desktop or shelf installation, grounding the switch, installing the power cord retainer, or rack installation.
- Connect the AC power cord into the rear of the switch and to an electrical outlet (preferably one that is grounded and surge protected).
- Refer to the User’s Guide included with your switch for more detailed information about its components, making network connections, and technical specifications.
Management Options
This system may be managed out-of-band through the console port on the front/back panel or in-band using Telnet. The user may also choose the web- based management, accessible through a web browser. Each Switch must be assigned its own IP Address, which is used for communication with an SNMP network manager or other TCP/IP application (for example BOOTP, TFTP). The Switch’s default IP address is 10.90.90.90. The user can change the default Switch IP address to meet the specification of your networking address scheme.
Web-based Management Interface
After a successful physical installation, you can configure the switch,
monitor the LED panel, and display statistics graphically using a web browser,
such as Microsoft® Internet Explorer version 7.0 and higher, Firefox, Chrome
or Safari.
You need the following equipment to begin the web configuration of your
device:
- A PC with a RJ-45 Ethernet connection
- A standard Ethernet cable
Step 1
Connect the Ethernet cable to any of the ports in front panel of the switch
and to the Ethernet port on the PC.
Step 2
In order to login and configure the switch via an Ethernet connection, the PC
must have an IP address in the same range as the switch. For example, if the
switch has an IP address of 10.90.90.90, the PC should have an IP address of
10.x.y.z (where x/y is a number between 0 ~ 254 and z is a number between 1
~254), and a subnet mask of 255.0.0.0.
Open your web browser and enter http://10.90.90.90 (the factory-default IP
address) in the address box. Then press
The
web configuration can also be accessed through the DNA. You can click the IP
hyper link in the device list in the DNA to open the web GUI of devices.
NOTE: The switch’s factory default IP address is 10.90.90.90 with a
subnet mask of 255.0.0.0 and a default gateway of 0.0.0.0
Step 3
When the following logon dialog box appears, enter “admin” for both the
Username and Password and choose the language of the Web-based Management
interface then click Login.
Step 4
Before entering the Web-based Management, the Smart Wizard will guide you to
quickly configure some functions, such as Ip Information, User Account and
SNMP Settings. If you don’t plan to change anything, click Exit to exit the
Wizard and enter the Web-based Management. For a detailed look at the Smart
Wizard’s functions, please refer to the Smart Wizard introduction in the user
manual.
DNA (D-Link Network Assistant)
The DNA (D-Link Network Assistant) is a program for discovering Switches with
the same L2 network segment connected to your PC. This tool can support
Windows 2000, XP, Vista, and Windows 7. There are two options for the
installation of DNA (D-Link Network Assistant), one is through the autorun
program on the installation CD and the other is manual installation.
Option 1: Follow these steps to install DNA via the autorun program on
the installation CD (in case the installation CD is included):
- Insert the CD into your CD-ROM Drive.
- The autorun program will pop up automatically.
- Simply click on the “Install DNA (D-Link Network Assistant)” button and an installation wizard will guide you through the process.
- After successfully installing the DNA, you can find it under Start > Programs > D-Link > DNA.
- Just connect the Switch to the same L2 network segment of your PC and use the DNA (D-Link Network Assistant) to discover the Switches.
Option 2: Follow these steps to install DNA manually (in case the installation CD is included):
- Insert the CD into your CD-ROM drive.
- From the Start menu on the Windows desktop choose Computer.
- Double click on your CD-ROM/DVD-Rom Drive to start the autorun menu, or right click on the Drive to open the folder. Select DNA (D-Link Network Assistant) and double click on the setup.exe file.
- Follow the on-screen instructions to install the utility.
- Upon completion, go to Start > Programs > D-Link > DNA and open DNA (D-Link Network Assistant).
- Just connect the Switch to the same L2 network segment of your PC and use DNA to discover the Switch.
Option 3: (in case the installation CD is not included: Download DNA
(D-Link Network Assistant) from Google Play at
https://play.google.com/store/apps/ and follow the on-screen instructions to
install the utility.
For detailed information of DNA, please refer the user manual.
Connecting The Console Port
To connect to the serial port, a special Console Cable must be used. This
cable is included with this product’s packaging. The cable referred to as an
RS-232 to RJ-45 connector cable specifically pinned to connect to this
switch’s serial port by using the correct pin configuration.
To connect to the console port of the Switch, use the following steps:
- Connect the RS-232 end of the console cable to the Serial Port of the management PC
- Connect the RJ-45 end of the console cable to the Console Port of the Switch.
- Open the HyperTerminal application (or any terminal emulation program capable of emulating a VT-100 terminal connection) on the management PC and configure the Properties of this connection.
- The Bits per second should be 115200 baud.
- The Data bits should be 8.
- The Parity should be None.
- The Stop bits should be 1.
- The Flow control should be None.
- Now the Switch can be turned on and access to the Switch’s CLI will be available.
Telnet Management
Users may also access the switch through Telnet using your PC’s Command
Prompt. To access it from your computer, users must first ensure that a valid
connection is made through the Ethernet port of the Switch and your PC, and
then click Start > Programs > Accessories > Command Prompt on your computer.
Once the console window opens, enter the command telnet 10.90.90.90
(depending on configured IP address) and press Enter on your keyboard. You
should be directed to the opening console screen for the Command Line
Interface of the switch, enter the “admin” for the default user name and
password for the Switch and press the Enter key.
Additional Information
If you are encountering problems setting up your network, please refer to the
user manual that came with the switch. It contains many more rules, charts,
explanations, and examples to help you get your network up and running.
Additional help is available through our offices listed at the back of the
user manual or online. To find out more about D-Link products or marketing
information, please visit the website http://www.dlink.com .
Warranty Information
The D-Link Limited Lifetime Warranty information is available at http://warranty.dlink.com/ .
References
- warranty.dlink.com/
- Smart Home, SMB and Enterprise solutions | D-Link
- Smart Home, SMB and Enterprise solutions | D-Link
- D-Link Главная
- D-Link Коммутаторы
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>