beckett M90AUL Submersible Fountain Pond Pump Kit Owner’s Manual

: June 10, 2024
: beckett

Table of Contents

beckett M90AUL Submersible Fountain Pond Pump Kit
Product Information
Product Usage Instructions
Models
Precautions
Installation Instructions
MAINTENANCE
LIMITED WARRANTY
Contact
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

beckett M90AUL Submersible Fountain Pond Pump Kit

Product Information

The Beckett submersible pumps are designed for use in pond and fountain applications. There are seven models available, including M90AUL, M160AUL, M160AS, M290AUL, M430AUL, M290AS, and M430AS. These pumps are carefully inspected and tested to ensure both safety and operating performance.

The National Electric Code requires the use of a ground fault circuit interrupter (GFCI) in the branch circuit supplying fountain pumps and other pond equipment. Please see your electrical supplies dealer for this device. The pump is supplied with a grounding conductor and ground attachment plug to reduce the risk of electric shock. Ensure that it is connected only to a properly grounded, grounding-type receptacle.

The pump must be operated in freshwater only and should not be used to pump flammable liquids or heated liquids. To prevent pump damage, do not let the pump run dry. The pump should be operated completely submerged for proper cooling.

Product Usage Instructions

Read and save the user manual for future reference.
Ensure the pump is connected to a properly grounded, grounding-type receptacle with a ground fault circuit interrupter (GFCI).
Do not remove the grounding pin from the plug.
Do not connect the pump to any voltage other than what is shown on the pump.
Use only on portable self-contained fountains no larger than 5 feet in any dimension to reduce the risk of electric shock.
Ensure that the electrical cord loops below the electrical outlet to form a Drip Loop to prevent water from running down the cord into the electrical outlet.
Always disconnect from the electrical outlet before handling the pump.
The pump must be submerged in water below sensor to operate.
For best results, operate the pump completely submerged and keep the water level above the minimum water level at all times.
Take out the back cover and wipe the Sensor clean periodically (3-6 months) for M160AS. Take out the Sensor Screen and wipe the Sensor eye clean periodically (3-6 months) for M290AS & M430AS.
If less flow is desired, adjust it with the flow control. Never restrict the pump’s intake.
To clean the pump, remove the front plate and the impeller. Use a small brush or stream of water to remove any debris. CAUTION: The pump shaft cannot be removed except M160AS.

Beckett pumps are carefully inspected and tested to ensure both safety and operating performance for pond and fountain applications. However, failure to follow the instructions and warnings in this manual may result in pump damage and/or serious injury. Be sure to read and save this manual for future reference.

Models

M90AUL, M160AUL
M160AS
M290AUL, M430AUL
M290AS & M430AS

Precautions

WARNING

The National Electric Code requires that a ground fault circuit interrupter (GFCI) be used in the branch circuit supplying fountain pumps and other pond equipment. See your electrical supplies dealer for this device.
Do not remove the grounding pin from the plug.
Do not connect to any voltage other than shown on the pump.
Do not pump flammable liquids.
Do not use with water above 87º Fahrenheit (30ºC).
To reduce the risk of electric shock, use only on portable self-contained fountains no larger than 5 feet in any dimension.
Risk of electrical shock. This pump is supplied with a grounding conductor and ground attachment plug. To reduce the risk of electric shock, be
certain that it is connected only to a properly grounded, grounding-type receptacle.
Ensure that the electrical cord loops below the electrical outlet to form a “Drip Loop”.
This will prevent water from running down the cord into the electrical outlet.

CAUTION

Always disconnect from electrical outlet before handling the pump.
Do not let the pump run dry.
Do not lift the pump by the power cord.
Do not pump heated liquids.
Operate in freshwater only.
Operate pump completely submerged for proper cooling.

ATTENTION

In order to get best results, operate pump completely submerged.
Keep the water level above the minimum water level at ALL TIMES.

Installation Instructions

MAINTENANCE

M160AS

For best results, take out the back cover, wipe the Sensor clean periodically (3-6 months).

M290AS &M430AS: For best results, take out the Sensor Screen, wipe the Sensor eye clean periodically (3-6 months).

Pump must be submerged in water below sensor to operate

A clogged or dirty intake screen will greatly reduce performance. If the pump is used on a dirty surface, raise it slightly to reduce the amount of debris contacting the intake.
If less flow is desired, adjust it with the flow control. Never restrict the pump’s intake.
To clean the pump, remove the front plate and the impeller. Use a small brush or stream of water to remove any debris.
_ CAUTION: _The pump shaft cannot be removed except M160AS.

IF THE PUMP FAILS TO OPERATE, CHECK THE FOLLOWING:

Check the circuit breaker and try another outlet to ensure the pump is getting electrical power.
NOTE: always disconnect from electrical outlet before handling the pump.
Check the pump discharge and tubing for kinks and obstructions. Algae build up can be flushed out with a garden hose.
Check the intake screen to ensure it is not clogged with debris.
Remove the pump inlet to access the impeller area. Turn the impeller to ensure it is not broken or jammed.
If the impeller area is encrusted with minerals or corrosion, gently scrape the area clean.
If your pump has been idle for an extended period, it may be necessary to apply a drop of light oil to the shaft and spin the impeller by hand until it turns freely.
Monthly maintenance will add to your pump’s life.

LIMITED WARRANTY

Each Beckett Corporation (“Beckett”) product is warranted to be free from defects in material and workmanship for the applicable Warranty Period (herein so called) set forth below. The Warranty Period for each product commences on the date of purchase by the original purchaser. The Warranty Periods are as follows:

Product Type or Name/ Warranty Period

Pump Models

FR Series, DP800-1800, G Series, FC Series ………… 2 Years
BK17/22 Series …………………………………. 2 Years
Other Pump Models …………………………………..1 Year
Pre-Formed Poly Ponds………………………..………15 Years
Waterfall Weir & Skimmer………………………..………. 5 Years

Liner Material

35 mil PVC……………………………20 Years
40 mil EPDM…………………………… 20 Years
20 mil PVC……………………………15 Years
UV9/UV13 Filter…………………………….. 1 Year
All Other Beckett Products.……………………………90 Days

APPLICATION: The warranty covers only properly installed and maintained Beckett products and is limited to the application at normal temperature 32º F to 86º F, (0º C to 30º C) pumping fluids with a specific gravity up to 1.1 and with a pH range of 5 to 9 (freshwater). Other liquid applications and extreme temperature uses must be approved in advance by Beckett.

The warranty does not apply to or cover damages or defects caused by external causes, including, but not limited to, improper or faulty installation or unauthorized modification, lightning, electrical surges, abuse, misuse or abnormal use or misapplication, including use in a manner inconsistent with the product’s intended function. The purchaser is responsible for determining the suitability of the product for its intended use. If products are damaged in transit, a claim should be filed with the carrier.

REMEDY: If there has been a failure to conform to the warranty, Beckett will, at Beckett’s option, repair, replace or issue a credit or refund for the particular nonconforming product or part. Repair, replacement, credit or refund, at Beckett’s option, is the exclusive remedy in the event of a failure to conform to the warranty. Warranty claims must be made within 3 months after the expiration of the applicable Warranty Period.

ADMINISTRATION: Warranty claims must be made by calling Beckett Corporation, Customer Service Dept., telephone 866-466-4319, or by emailing CustomerService@BeckettUS.com. Proof of purchase is required, and a shipping and handling fee applies to all warranty replacements.

INSTALLATION, REMOVAL AND/OR SHIPPING CHARGES: The warranty does not cover any costs associated with the installation, removal or shipping of products subject to warranty claims.

DISCLAIMER AND LIMITATION: THE EXPRESS WARRANTY AND REMEDIES SET FORTH ABOVE ARE EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES AND REMEDIES, WHETHER ORAL OR WRITTEN, EXPRESS OR IMPLIED. TO THE FULL EXTENT PERMITTED BY LAW, BECKETT EXPRESSLY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. IF IMPLIED WARRANTIES CANNOT BE DISCLAIMED, ALL SUCH IMPLIED WARRANTIES ARE LIMITED TO THE DURATION OF THE APPLICABLE EXPRESS WARRANTY.

BECKETT DOES NOT ACCEPT LIABILITY BEYOND THE REMEDIES EXPRESSLY SET FORTH IN THIS WARRANTY. IN NO EVENT SHALL BECKETT BE LIABLE OR RESPONSIBLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. BECKETT’S AGGREGATE LIABILITY UNDER THIS WARRANTY OR WITH RESPECT TO ANY PRODUCT COVERED HEREBY, UNDER ANY LEGAL THEORY, SHALL NOT EXCEED THE PURCHASE PRICE PAID FOR THE NONCONFORMING PRODUCT. THE LIMITATIONS CONTAINED IN THIS PARAGRAPH SHALL NOT APPLY TO INJURY TO THE PERSON.

SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES OR EXCLUSIONS OR LIMITATIONS ON THE DURATION OF AN IMPLIED WARRANTY, SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS THAT VARY FROM STATE TO STATE.

APPLICABLE LAW: THE TERMS AND CONDITIONS EXPRESSED HEREIN SHALL BE CONSTRUED AND GOVERNED IN ACCORDANCE WITH THE LAWS OF THE STATE OF TEXAS.