EXOR eX7xxM Powerful Multi Purpose HMIs Installation Guide
- June 11, 2024
- EXOR
Table of Contents
- DIMENSION-CUT OUT
- FIXING BRACKE
- REAR VIEW
- POWER SUPPLY
- CONNECTIONS
- EXPANSION SLOT FOR PLUG-IN MODULES
- DISPOSE OF BATTERIES
- USAGE IN EXPLOSION-HAZARDOUS AREAS ZONE 2 AND ZONE 22
- STANDARDS AND APPROVALS
- SPECIAL INSTRUCTION FOR USE
- TECHNICAL DATA
- PRODUCT IDENTIFICATION
- MODULE PLUGIN OPTIONNEL
- IDENTIFICATION DU PRODUIT
- INSTALLATION PROCEDURE
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
MANEX7xxMU002 V.1.02 20.12.2022
eX7xxM
Installation guide
DIMENSION-CUT OUT
Model | A | B | C | H | L |
---|---|---|---|---|---|
eX707M | 176mm/06.90″ | 136mm/05.35″ | 47mm/01.85″ | 147mm/05.79″ | 187mm/07.36″ |
eX710M | 271mm/10.66″ | 186mm/07.32″ | 56mm/02.20″ | 197mm/07.75″ | 282mm/11.10″ |
eX712M | 332,5mm/13.09″ | 151 mm/05.94″ | 49mm/01.92″ | 163mm/06.41″ |
344,5mm/13.16″
eX715M| 411mm/16.18″| 256mm/10.00″| 56mm/02.20″| 267mm/10.50″| 422mm/16.60″
eX721 M| 541mm/21.30″| 336mm/13.22″| 56mm/02.20″| 347mm/13.66″| 552mm/21.73″
Model| CSD| CSD2
---|---|---
eX707M| 850mm/33.46″| 400mm/15.75″
eX710M| 1150mm/45.28″| 750mm/29.53″
eX712M| 400mm/15.75″| 100mm/03.93″
eX715M| 1800mm/70.87″| 1300mm/51.18″
eX721 M| 2200mm/86.61″| 1300mm/51.18″
FIXING BRACKE
A) eX7xxM
B) Cut-out on a flat surface (min wall thickness 1.2mm) **** Tightening
torque: 130Ncm±5Ncm or screw each fixing screw until the bezel corner gets in
contact with the panel.
REAR VIEW
| Description
---|---
1| USB port V2.0, max. 500 mA
2| Ethernet port 2 (10/100 Mb)
3| Ethernet port 1 (10/100 Mb)
4| Serial port
5| Ethernet port 0 (10/100/1000 Mb)
6| Power supply
7| 2 Expansion slots for plugin modules
8| SD Card Slot
- for maintenance only only
All ports are SELV (Safety Extra – Low Voltage) according European
Standards and Class 2 according UL Standards
WARNING – EXPLOSION HAZARD – (Ethernet, USB connectors, memory card
slot) DO NOT CONNECT OR DISCONNECT UNLESS THE POWER HAS BEEN DISCONNECTED OR
THE AREA IS KNOWN TO BE FREE OF IGNITABLE CONCENTRATIONS.
**** Don’t open the panel rear cover when the power supply is applied.
POWER SUPPLY
** Extra low voltage power supply / Limited power source.DC
Power Connector, Female – R/C Terminal Blocks (XCFR2), manufactured by Weid
muller Inc., Cat. No. BLZ 5.08, torque 4.5 lb-in
Do not open the cabinet while the system is powered up.
WARNING:** Do not separate when energized.
The unit must always be grounded to earth with 1.5mmq wire size minimum. Earth
connection will have to be done using either the screw or the faston terminal
located near the power supply terminal block. Also connect to ground the
terminal 3 on the power supply terminal block. All the electronic devices in
the control system must be properly grounded. Grounding must be performed
according to applicable regulations.
**** Ensure that the power supply has enough power capacity for the operation of the equipment.
CONNECTIONS
To operate in RS-485 pins 1-2 and 4-3 must be connected externally
PIN | Description |
---|---|
1 | RX/CHB- |
2 | TX/CHA- |
3 | CTS/CHB+ |
4 | RTS/CHA+ |
5 | +5V output |
6 | GND |
8 | SHIELD |
EXPANSION SLOT FOR PLUG-IN MODULES
The validity of UL certification is ensured only by using accessories (PLxx) covered by the same certificate.
DISPOSE OF BATTERIES
These devices are equipped with rechargeable Lithium battery, not user-
replaceable.
Dispose of batteries according to local regulations.
This device cannot be disposed of as a domestic waste but accord- ing to
WEEE European Directive 2012/19/EU
USAGE IN EXPLOSION-HAZARDOUS AREAS ZONE 2 AND ZONE 22
The connection and installation have to be done in conformity with ATEX
Directive, IEC EN 60079-14, and have to be performed by authorized, qualified
personnel and in possession of necessary skills.
Confirm that the location is free from explosively hazardous gases or
dust beforeconnecting or disconnecting equipment, replacing or wiring modules.
Confirm that thepower supply has been turned OFF before disconnecting,
replacing or wiring modules.
Before turning ON, clean the front panel of the graphic panel with a
damp cloth to avoid any electrostatic discharge.
The graphic panel must not be exposed to direct sunlight.
The vents in the panel casing must not be obstructed.
Do not allow layers of dust to form on the graphic panel: it should be cleaned
regularlymaking clean with a damp cloth.
Check that graphic panels are mounted in enclosures satisfying minimum IP54
degree ofprotection for category 3G and IP6x for category 3D and the
requirements relating to the 3Gor 3D categories in Zones 2/22 (Category 3:
normal level of protection – G: Gas – D: Dust).
End User is responsible to ensure that the maximum operating temperature
is not exceeded in the end use application
Ensure that the labelling specifications are compatible with the
conditions permitted for the hazardous area at the site where it is being used
(Zones 2/22 Group II: Surface industries – Category 3: Normal level of
protection – G: Gas – D: Dust – IP: degree of protection (protection against
solids and liquids) – T: maximum surface temperature).
ATEX markings, apllied to the Models
DEMKO 17 ATEX 1871X / UL22UKEX2726X
II 3G Ex ec IIC T5…T4 Gc 0°C≤Tamb≤+50°C or -20°C≤Tamb≤+60°C
II 3D Ex tc IIIC T95°C Dc
T Amb: 0°C – +50°C or -20°C – +60°C
Type examination certificate number:
**** DO NOT DISCONNECT WHILE CIRCUIT IS LIVE
IECEx markings, apllied to the Models
IECEx: IECEx ULD 17.0019X
Ex ec IIC T5…T4 Gc 0°C≤Tamb≤+50°C or -20°C≤Tamb≤+60°C Ex tc IIIC T95°C Dc
Type examination certificate numbe
The products have been designed for use in an industrial environment in
compliance with the 2014/30/EU directive
Software available in these products is based on OpenSource. Visit
oss.exorint.net for more details.
The products have been designed in compliance with
EN 61000-6-4 | EN 61000-4-3 |
---|---|
EN 61000-6-2 | EN 61000-4-4 |
EN 60945 | EN 61000-4-5 |
EN 60079-0 | EN 61000-4-6 |
EN 60079-7 | EN 61000-4-8 |
EN 60079-31 | EN 61000-4-11 |
EN 61000-4-2 | EN 61000-4-29 |
Equipment group II, category 3 intended for use in potentially explosive
atmospheres zones
2/22, G:gas and D:dust.
Type examination certificate number
DEMKO 17 ATEX 1871 / UL22UKEX2726X
The installation of these devices into the residential, commercial and light-
industrial environments is allowed only in the case that special measures are
taken in order to get the conformity to IEC-61000-6.3.
WARNING – Power, input and output (I/O) wiring must be in accordance with
Class I, Division 2 wiring methods, Article 501.10 (B) of the National
Electrical Code, NFPA 70 for installation in the U.S., or as specified in
Section 18-1J2 of Canadian Electrical Code for installations within Canada and
in accordance with the authority having jurisdictions.
A. WARNING – EXPLOSION HAZARD – SUBSTITUTION OF ANY COMPONENT MAY IMPAIR
SUITABILITY FOR CLASS I, DIVISION 2
B. WARNING – EXPLOSION HAZARD – WHEN IN HAZARDOUS LOCATIONS, TURN OFF OWER
BEFORE REPLACING OR WIRING MODULES, and
C. WARNING – EXPLOSION HAZARD – DO NOT DISCONNECT EQUIPMENT WHILE THE CIRCUIT
IS LIVE OR UNLESS THE AREA IS KNOW TO BE FREE OF IGNITABLE CONCENTRATIONS.
D. SUITABLE FOR USE IN CLASS I, DIVISION 2, GROUPS A, B, C AND D HAZARDOUS
LOCATIONS, OR NONHAZARDOUS LOCATIONS ONLY.
E. WARNING – EXPLOSION HAZARD – DO NOT CHANGE BATTERY UNLESS THE AREA IS KNOWN
TO BE FREE OF IGNITABLE CONCENTRATIONS
F. This equipment, except for the front panel display, is an open-type device
and is required to be installed in an enclosure suitable for the environment
such that the internal part of the equipment is only accessible with the use
of a tool.
STANDARDS AND APPROVALS
IECEx | IECEx: IECEx ULD 17.0019X |
---|---|
IEC 60079-0 | Ex ec IIC T5…T4 Gc 0°C≤Tamb≤+50°C or -20°C≤Tamb≤+60°C |
IEC 60079-7 | Ex tc IIIC T95°C Dc |
IEC 60079-31
ATEX| DEMKO 17 ATEX 1871X / UL22UKEX2726X
EN 60079-0| II 3G Ex ec IIC T5…T4 Gc 0°C≤Tamb≤+50°C or -20°C≤Tamb≤+60°C
EN IEC 60079-7 + A1| II 3D Ex tc IIIC T95°C Dc
CENELEC EN 60079-31
SPECIAL INSTRUCTION FOR USE
-
For EPL Gc,
– the equipment shall only be used in an area of at least pollution degree 2, as defined in IEC/ EN 60664-1.
– the equipment shall be installed through an end-equipment enclosure that provides a minimum ingress protection of IP54 in accordance with IEC/EN 60079-0, suitable for applicable Gas Group, Temperature Classification and Ambient temperature range; and
– transient protection shall be provided that is set at a level not exceeding 140% of the peak rated voltage value at the supply terminals to the equipment. -
For EPL Dc, the equipment shall be installed through an end-eqipment enclosure that provides a minimum ingress protection of IP6X in accordance with IEC/EN 60079-0, suitable for applicable Dust Group, Temperature Classification and Ambient temperature range.
-
Care shall be taken not to allow layers of dust to form on the graphic panel in a way that might cause the accumulation of static charges.
-
eX700 series have only been evaluated for low risk of mechanical impact.
The relation between maximum ambient temperature and the assigned temperature class is as follow:
Maximum Ambient Temperature Range | Temperature Class |
---|---|
-20°C up to 60°C | T4 |
0°C up to 50°C | T5 |
Ambient temperature range: the ambient temperature range is –20°C≤Tamb≤+60°C.
The ambient temperature range is limited to 0°C≤Tamb≤+50°C when installed with
plug-in module, model PLIO03 with Part Number PLIO03xxxxY with Y≤2.
TECHNICAL DATA
| All models / Alle Modelle
---|---
Display/Backlight| TFT Color / LED
Colors| 16M
Dimming| yes
SD card slot| yes
Serial Port| RS-232,RS-485, RS-422 Software configurable
Ethernet port| 2 10/100Mb,
1 10/100/1000Mb
USB port| 2 Host interface version 2.0
max. 500mA
Expansion slot| 2 Optional Plugin
Battery| rechargeable
Real Time Clock| yes
Voltage| 24Vdc
| eX707M| eX710M| eX712M
---|---|---|---
Resolution| 800X480| 1280X800| 1920X720
Diagonal (inches)| 7′ widescreen| 10.1’widescreen| 12.3″ widescreen
User memory flash| 4GB| 4GB| 8GB
Recipe memory| 1GB| 1GB| 2GB
Current rating 24VDC| 0.7A| 1.00A| 1.10A
Weight| 1.3 Kg| 1.7 Kg| 1.8 Kg
| eX715M| eX721M
---|---|---
Resolution| 1366X768| 1920X1080
Diagonal (inches)| 15.6 widescreen| 21.5Widescreen
User memory flash| 8GB| 8GB
Recipe memory| 2GB| 2GB
Current rating 24VDC| 1.2A| 1.7A
Weight| 4.1 Kg| 6.1 Kg
PRODUCT IDENTIFICATION
The product may be identified through a plate attached to the rear cover. You will have to know the type of unit you are using for correct usage of the information contained in the guide. An example of this plate is shown in the figure below:
product model name | eX707M |
---|---|
product part number | EX707MU5P1 |
year/week of production | 2116 |
serial number | AA00011TN000000561AA |
version id of the product | 120408A04002000 |
manufacturer address and | Exor International S.p.A. |
read instruction warning | Via Monte Fiorino 9-13 |
IT-37057 San Giovanni Lupatoto (VR)
ATEX Marking| DEMKO 17 ATEX 1871X / UL22UKEX2726X
II 3G Ex ec IIC T5…T4 Gc 0°C≤Tamb≤+50°C or -20°C≤Tamb≤+60°C
II 3D Ex tc IIIC T95°C Dc
IECEx Marking| IECEx: IECEx ULD 17.0019X
Ex ec IIC T5…T4 Gc 0°C≤Tamb≤+50°C or -20°C≤Tamb≤+60°C
Ex tc IIIC T95°C Dc
MODULE PLUGIN OPTIONNEL
IDENTIFICATION DU PRODUIT
product model name | PLCM01 |
---|---|
product part number | PLCM01U0P1 |
year/week of production | 2243 |
serial number | AA0000225000000561AA |
version id of the product | 050100A00000000 |
manufacturer address and read | Exor International S.p.A. |
instruction warning | Via Monte Fiorino 9-13 IT-37057 San Giovanni Lupatoto |
(VR)
INSTALLATION PROCEDURE
| Application| Max modules| Connecteur
---|---|---|---
PLCM01| CAN| 2| Y
PLCM01-NE| CAN| 2| N
PLCM05| CODESYS License| 1| Y
PLCM09X| 3G Modem| 1| Y
PLIO03| Multifunction I/O| 1| N
PLCM01 / PLCM01-NE| Operating temperature -20°C to 60°C
---|---
PLCM05| Operating temperature -20°C to 60°C
PLCM09X| Operating temperature -20°C to 60°C
PLIO03*| with part number PLIO03xxxxY where:
– Y≤2 is operating temperature range 0°C≤Tamb≤+50°C with
Operating Temperature Code T5 (vertical installation), 12-30VDC
– Y>2 is operating temperature range –20°C≤Tamb≤+60°C with
Operating Temperature Code T4 (vertical installation), 12-30VDC
**** PLCM and PLIO03 electrical ratings:
– PLCM01: For electrical rating refers to the host eX700 models.
– PLCM05: For electrical rating refers to the host eX700 models and PLIO03
ratings
– PLCM09X: 2xDigital Inputs voltage 12÷30 Vdc, 3mA; 2xDigital Outputs voltage
12÷30 Vdc, 0.5A
– PLIO03: 20xDigital Inputs voltage 12÷30 Vdc; 12xDigital Outputs voltage
12÷30 Vdc, 0.5A; 4xAnalog inputs 0÷10 Vdc, 4-20mA; 4xAnalog outputs: 0÷10 Vdc,
4-20mA
Reproduction of the contents of this copyrighted document, in whole or part,
without written permission of Exor International S.p.A., is prohibited.
User Manual available on
www.exorint.com
MANEX7xxMU002 V.1.02 20.12.2022
© 2020-2022 Exor International S.p.A
Exor International S.p.A. – San Giovanni Lupatoto VR, Italy
www.exorint.com
MANEX7xxMU002 V.1.02 20.12.2022
© 2020-2022 Exor International S.p.A
Exor International S.p.A. – San Giovanni Lupatoto VR, Italy
www.exorint.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>