Vanatoo Transparent One Encore Powered Bluetooth Speaker User Guide
- June 11, 2024
- Vanatoo
Table of Contents
Vanatoo Transparent One Encore Powered Bluetooth Speaker User Guide
Unpack Your System
- Active speaker
- Passive speaker
- 2 Grills
- IR remote control
- Optional isolation feet
- USB A to USB B cable
- 3.5 mm to 3.5 mm cable
- Four conductor speaker wire
- 3.5 mm to RCA “Y” cable
- AC power cord
- Quick Start Guide and a Safety Sheet
Connect the Speakers
The included speaker interconnect cable with screw-on collar connectors makes
this quick and easy.
Connect Power
- Make sure the power switch (2) is in the OFF position.
- Plug the AC power cord into the active speaker.
- Plug the AC power cord into the power outlet.
Connect Your Audio Source
Turn the volume controls on the speaker (1) and on the audio source both to
minimum.
- Analog (3) — Connect your source using the included using 3.5mm to 3.5mm cable or 3.5mm to RCA cable as appropriate for your source component.
- Digital Coax (4) — Connect your source component using a 75 ohm digital coaxial RCA cable.
- Optical (5) — Connect your source component to the Vanatoo T1E Plus using a Toslink optical cable.
- USB (6) — Connect your computer to the T1E Plus using the supplied USB A to USB B cable. Select the Vanatoo T1E Plus in your computer’s audio settings.
- Bluetooth —
a. Press and release the “Pair-Prog” button (7) on the rear of the active speaker, or press “Enable” and then “BT Pair” on the remote control. The bluetooth interface will remain in pair mode for 2 minutes.
b. Ensure Bluetooth is turned-on on your source device and pair with the Vanatoo T1E Plus.
c. Ensure your source device is connected to the Vanatoo T1E Plus over Bluetooth and play music!
Designate Left-Right speaker
Set the Left–Right switch (9) to designate whether the active speaker is
located to your right or left (as you face the speakers). This ensures the
music is recreated as it was recorded.
Install the Grills
Grills come in individual plastic bags. Simple magnetic mounting (no or little
alignment necessary). Can go either way such that the “Vanatoo” logo is
upright on the bottom.
Listen to Music!
Turn the power switch to the ON position (2). The blue LED (8) will light up
within5 seconds to indicate power to the unit. In most applications you can
set the T1E Plus volume control to 100% and adjust the volume up/down from
your source (Computer, Bluetooth device, etc).
Remote Control
The included IR Remote Control is especially handy when your T1E Plus is used
with a TV, or for switching sources, adjusting bass and treble, etc. Note that
you must hit the “Enable” button to enable the other buttons inside the
rectangular box for 15 seconds.
Optional Settings
The T1E Plus has a lot of setup options, such as enabling the speakers to play
mono, disabling sleep mode, varying the LED brightness, connecting a subwoofer
and alternate bass profiles for room placement. Go to
www.vanatoo.com/support/downloads
to download the user manual for a full description of the T1E Plus and its
setup options.
CONGRATULATIONS!! That’s it! We hope you enjoy your
Vanatoo Transparent One Encore Plus powered speakers. For additional setup up
information, connectivity options, and the troubleshooting guide, check out
the Transparent One Encore Plus Owner’s Guide or visit us at
www.vanatoo.com.
Contact Us
Email: [email protected]
SAFETY PRECAUTIONS
-
This lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point, within an equilateral triangle, is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. -
To prevent risk of fire or electric shock, avoid overloading the wall outlet, extension cords.
-
WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. The apparatus shall not be exposed to dripping or splashing and that objects filled with liquids, such as vases, shall not be placed on apparatus.
-
Read these instructions.
-
Keep these instructions.
-
Heed all warnings.
-
Follow all instructions.
-
Do not use this apparatus near water.
-
Clean only with dry cloth.
-
Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
-
Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
-
Do not defeat the safety purpose of the polarized or grounding plug. A polarized plug has two blades with one wider than the other. A grounding plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
-
Protect the power cord from being walked on or pinched particularly at the plugs, convenience receptacles, and at the point where they exit from the apparatus.
-
Use only attachments/accessories specified by the manufacturer.
-
Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart or rack is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
-
Unplug the apparatus during lightning storms or when unused for long periods of time.
-
Refer all servicing to qualified personnel. Servicing is required when the apparatus has been damaged in any way, such as when power supply cord or plug is damaged, when liquid has been spilled or objects have fallen into the apparatus, or when the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
-
WARNING: The mains plug/appliance coupler is used as the disconnect device. The disconnect device shall remain readily operable.
-
The woofer cone and tweeter dome are fragile. Do not touch.
-
This equipment is a Class II or double insulated electrical appliance. It has been designed in such a way that it does not require a safety connection to electrical earth.
-
Battery Notice:
a) Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.
b) Do not ingest the battery, Chemical Burn Hazard.
c) The remote control supplied with the product contains a Lithium coin/button cell battery. If the coin/button cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death.
d) Keep new and used batteries away from children.
e) If the battery compartment does not close securely, stop using the product and keep it away from children.
f) If you think the battery might have been swallowed or placed inside any part of the body, seek immediate medical attention.
g) The battery shall not be exposed to excessive heat such as sunshine, fire or the like.
h) Do not handle leaking or damaged Lithium batteries.
i) Risks of leakage. Only use the specified type of battery. Observe correct polarity. Remove the battery from a product that are not in use for an extended period of time. Store batteries in a dry place.
j) Do not recharge non-rechargeable batteries.
k) Avoid exposure to extreme heat or cold.
l) This product contains a Lithium coin cell battery. If misused or abused this can result in:
Smoke or gas hazard
Heat hazard
Fire hazard
Explosion hazard
FCC STATEMENTS
FCC EMC COMPLIANCE INFORMATION
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Approved under the verification provision of FCC Part 15 as a Class B Digital Device. Caution: Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate this device.
FCC WIRELESS TRANSMITTER COMPLIANCE INFORMATION
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body
CANADA, INNOVATION, SCIENCE AND ECONOMIC DEVELOPMENT CANADA (ISED)
NOTICES
This device contains licence-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada’s licence-exempt
RSS(s). Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
RADIO FREQUENCY (RF) EXPOSURE INFORMATION
The radiated output power of the Wireless Device is below the Innovation,
Science and Economic Development Canada USED) radio frequency exposure limits.
The Wireless Device should be used in such a manner such that the potential
for human contact during normaloperation is minimized. This device has also
been evaluated and shown compliant With the ISED RF Exposure limits under
mobile exposure conditions. (antennas are greater than 20cm from a person’s
body).