CASIO 3529 Smart Watch User Guide
- June 11, 2024
- Casio
Table of Contents
3529 Smart Watch
MA2304-EA
© 2023 CASIO COMPUTER CO., LTD.
Watch Operation Guide 3529
Contents
Precautions
Operating Precautions User Maintenance Battery Replacement
Before Getting Started
General Guide Indicators Navigating Between Modes Viewing the Face in the Dark
Time Adjustment
Adjusting the Current Time Setting
Alarm
Configuring Alarm Settings Enabling/Disabling an Alarm or the Hourly Time
Signal Turning Off an Alarm or the Hourly Time Signal
Stopwatch
Measuring Elapsed Time Measuring a Split Time Timing the First and Second
Place Finishers
Timer
Setting the Time Using the Timer
Other Settings
Configuring Flash Alert Settings
Other Information
Specifications
Troubleshooting
OPUM-H
1
Watch Operation Guide 3529
Precautions
Operating Precautions
Water Resistance
The information below applies to watches with WATER RESIST or WATER RESISTANT
marked on the back cover.
Water Resistance Under Daily Use
Marking on watch front or on back cover
Example of Daily Use
No BAR mark
Hand washing, rain
Yes
Water-related work, swimming
No
Windsurfing
No
Skin diving
No
Enhanced Water Resistance Under Daily Use 5 Atmospheres
Marking on watch front or on back cover
Example of Daily Use
5BAR
Hand washing, rain
Yes
Water-related work, swimming Yes
Windsurfing
No
Skin diving
No
10 Atmospheres
Marking on watch front or on back cover
Example of Daily Use
10BAR
Hand washing, rain
Yes
Water-related work, swimming Yes
Windsurfing
Yes
Skin diving
Yes
20 Atmospheres
Marking on watch front or on back cover
Example of Daily Use
20BAR
Hand washing, rain
Yes
Water-related work, swimming Yes
Windsurfing
Yes
Skin diving
Yes
Do not use your watch for scuba diving or other types of diving that requires
air tanks.
Watches that do not have WATER RESIST or WATER RESISTANT marked on the back
cover are not protected against the effects of sweat. Avoid using such a watch
under conditions where it will be exposed to large amounts of sweat or
moisture, or to direct splashing with water.
Even if a watch is water resistant, note the usage precautions described
below. Such types of use reduce water resistance performance and can cause
fogging of the glass. Do not operate the crown or buttons while your watch is
submersed in water or wet. Avoid wearing your watch while in the bath. Do not
wear your watch while in a heated swimming pool, sauna, or any other high
temperature/high humidity environment. Do not wear your watch while washing
your hands or face, while doing housework, or while performing any other task
that involves soaps or detergents.
After submersion in seawater, use plain water to rinse all salt and dirt from
your watch.
To maintain water resistance, have the gaskets of your watch replaced
periodically (about once every two or three years).
A trained technician will inspect your watch for proper water resistance
whenever you have its battery replaced. Battery replacement requires the use
of special tools. Always request battery replacement from your original
retailer or from an authorized CASIO service center.
Some water-resistant watches come with fashionable leather bands. Avoid
swimming, washing, or any other activity that causes direct exposure of a
leather band to water.
The inside surface of the watch glass may fog when the watch is exposed to a
sudden drop in temperature. No problem is indicated if the fogging clears up
relatively quickly. Sudden and extreme temperature changes (such as coming
into an air conditioned room in the summer and standing close to an air
conditioner outlet, or leaving a heated room in the winter and allowing your
watch to come into contact with snow) can cause it to take longer for glass
fogging to clear up. If glass fogging does not clear up or if you notice
moisture inside of the glass, immediately stop using your watch and take it to
your original retailer or to an authorized CASIO service center.
Your water-resistant watch has been tested in accordance with International
Organization for Standardization regulations.
Band
Tightening the band too tightly can cause you to sweat and make it difficult
for air to pass under the band, which can lead to skin irritation. Do not
fasten the band too tightly. There should be enough room between the band and
your wrist so you can insert your finger.
Deterioration, rust, and other conditions can cause the band to break or come
off of your watch, which in turn can cause band pins to fly out of position or
to fall out. This creates the risk of your watch falling from your wrist and
becoming lost, and also creates the risk of personal injury. Always take good
care of your band and keep it clean.
Immediately stop using a band if you even notice any of the following: loss of
band flexibility, band cracks, band discoloration, band looseness, band
connecting pin flying or falling out, or any other abnormality. Take your
watch to your original retailer or to a CASIO service center for inspection
and repair (for which you will be charged) or to have the band replaced (for
which you will be charged).
2
Watch Operation Guide 3529
Temperature
Never leave your watch on the dashboard of a car, near a heater, or in any
other location that is subject to very high temperatures. Do not leave your
watch where it will be exposed to very low temperatures. Temperature extremes
can cause your watch to lose or gain time, to stop, or otherwise malfunction.
Leaving your watch in an area hotter than +60 °C (140 °F) for long periods can
lead to problems with its LCD. The LCD may become difficult to read at
temperatures lower than 0 °C (32 °F) and greater than +40 °C (104 °F).
Impact
Your watch is designed to withstand impact incurred during normal daily use
and during light activity such as playing catch, tennis, etc. Dropping your
watch or otherwise subjecting it to strong impact, however, can lead to
malfunction. Note that watches with shock-resistant designs (G-SHOCK, BABY-G,
G-MS) can be worn while operating a chain saw or engaging in other activities
that generate strong vibration, or while engaging in strenuous sports
activities (motocross, etc.)
Magnetism
Though a digital watch normally is not affected by magnetism, very strong
magnetism (from medical equipment, etc.) should be avoided because it can
cause malfunction and damage to electronic components.
Electrostatic Charge
Exposure to very strong electrostatic charge can cause your watch to display
the wrong time. Very strong electrostatic charge even can damage electronic
components.
Electrostatic charge can cause the display to go blank momentarily or cause a
rainbow effect on the display.
Chemicals
Do not allow your watch to come into contact with thinner, gasoline, solvents,
oils, or fats, or with any cleaners, adhesives, paints, medicines, or
cosmetics that contain such ingredients. Doing so can cause discoloration of
or damage to the resin case, resin band, leather, and other parts.
Storage
If you do not plan to use your watch for a long time, thoroughly wipe it free
of all dirt, sweat, and moisture, and store it in a cool, dry place.
Resin Components
Allowing your watch to remain in contact with other items or storing it
together with other items for long periods while it is wet can cause color on
resin components to transfer to the other items, or the color of the other
items to transfer to the resin components of your watch. Be sure to dry off
your watch thoroughly before storing it and make sure it is not in contact
with other items.
Leaving your watch where it is exposed to direct sunlight (ultraviolet rays)
for long periods or failure to clean dirt from your watch for long periods can
cause it to become discolored.
Friction caused by certain conditions (strong external force, sustained
rubbing, impact, etc.) can cause discoloration of painted components.
If there are printed figures on the band, strong rubbing of the printed area
can cause discoloration.
Leaving your watch wet for long periods can cause fluorescent color to fade.
Wipe the watch dry as soon as possible after it becomes wet.
Semi-transparent resin parts can become discolored due to sweat and dirt, and
if exposed to high temperatures and humidity for long periods.
Daily use and long-term storage of your watch can lead to deterioration,
breaking, or bending of resin components. The extent of such damage depends on
usage conditions and storage conditions.
Leather Band
Allowing your watch to remain in contact with other items or storing it
together with other items for long periods while it is wet can cause the color
of the leather band to transfer to the other items or the color of the other
items to transfer to the leather band. Be sure to dry off your watch
thoroughly with a soft cloth before storing it and make sure it is not in
contact with other items.
Leaving a leather band where it is exposed to direct sunlight (ultraviolet
rays) for long periods or failure to clean dirt from a leather band for long
periods can cause it to become discolored.
CAUTION: Exposing a leather band to rubbing or dirt can cause color transfer
and discoloration.
Metal Components
Failure to clean dirt from metal components can lead to formation of rust,
even if components are stainless steel or plated. If metal components exposed
to sweat or water, wipe thoroughly with a soft, absorbent cloth and then place
the watch in a well-ventilated location to dry.
Use a soft toothbrush or similar tool to scrub the metal with a weak solution
of water and a mild neutral detergent, or with soapy water. Next, rinse with
water to remove all remaining detergent and then wipe dry with a soft
absorbent cloth. When washing metal components, wrap the watch case with
kitchen plastic wrap so it does not come into contact with the detergent or
soap.
Bacteria and Odor Resistant Band
The bacteria and odor resistant band protects against odor generated by the
formation of bacteria from sweat, which ensures comfort and hygiene. In order
to ensure maximum bacteria and odor resistance, keep the band clean. Use an
absorbent soft cloth to thoroughly wipe the band clean of dirt, sweat, and
moisture. A bacteria and odor resistant band suppresses the formation of
organisms and bacteria. It does not protect against rash due to allergic
reaction, etc.
Liquid Crystal Display
Display figures may be difficult to read when viewed from an angle.
Note that CASIO Computer Co., Ltd. assumes no responsibility for any damage or
loss suffered by you or any third party arising through the use of your watch
or its malfunction.
3
Watch Operation Guide 3529
User Maintenance
Caring for Your Watch
Remember that you wear your watch next to your skin, just like a piece of
clothing. To ensure your watch performs at the level for which it is designed,
keep it clean by frequently wiping with a soft cloth to keep your watch and
band free of dirt, sweat, water and other foreign matter.
Whenever your watch is exposed to sea water or mud, rinse it off with clean
fresh water.
For a metal band or a resin band with metal parts, use a soft toothbrush or
similar tool to scrub the band with a weak solution of water and a mild
neutral detergent, or with soapy water. Next, rinse with water to remove all
remaining detergent and then wipe dry with a soft absorbent cloth. When
washing the band, wrap the watch case with kitchen plastic wrap so it does not
come into contact with the detergent or soap.
For a resin band, wash with water and then wipe dry with a soft cloth. Note
that sometimes a smudge like pattern may appear on the surface of a resin
band. This will not have any effect on your skin or clothing. Wipe with a
cloth to remove the smudge pattern.
Clean water and sweat from a leather band by wiping with a soft cloth.
Not operating a watch crown, buttons, or rotary bezel could lead to later
problems with their operation. Periodically rotate the crown and rotary bezel,
and press buttons to maintain proper operation.
Dangers of Poor Watch Care
Rust
Though the metal steel used for your watch is highly rust-resistant, rust can
form if your watch is not cleaned after it becomes dirty. Dirt on your watch
can make it impossible for oxygen to come into contact with the metal, which
can lead to breakdown of the oxidization layer on the metal surface and the
formation of rust.
Rust can cause sharp areas on metal components and can cause band pins to fly
out of position or to fall out. If you ever notice any abnormality immediately
stop using your watch and take it to your original retailer or to an
authorized CASIO service center.
Even if the surface of the metal appears clean, sweat and rust in crevasses
can soil the sleeves of clothing, cause skin irritation, and even interfere
with watch performance.
Premature Wear
Leaving sweat or water on a resin band or bezel, or storing your watch an area
subject to high moisture can lead to premature wear, cuts, and breaks.
Skin Irritation
Individuals with sensitive skin or in poor physical condition may experience
skin irritation when wearing a watch. Such individuals should keep their
leather band or resin band particularly clean. Should you ever experience a
rash or other skin irritation, immediately remove your watch and contact a
skin care professional.
Battery Replacement
Leave battery replacement up to your original retailer or authorized CASIO
service center.
Have the battery replaced only with the type specified in the
“Specifications”. Use of a different battery type can cause malfunction.
When replacing the battery, also request a check for proper water resistance.
Ornamental resin components may become worn, cracked, or bent over time when
subjected to normal daily use. Note that if cracking or any other abnormality
indicating possible damage is noticed in a watch submitted for battery
replacement, your watch will be returned with an explanation of the
abnormality, without the requested servicing being performed.
Initial Battery
The battery that comes loaded in your watch when you purchase it is used for
function and performance testing at the factory.
The test battery may go dead quicker than the normally rated battery life
noted in the “Specifications”. Note that you will be charged for replacement
of this battery, even if replacement is required within your watch’s warranty
period.
Low Battery Power
Low battery power is indicated by large timekeeping error, by dim display
contents, or by a blank display.
Operation while battery power is low can result in malfunction. Replace the
battery as soon as possible.
4
Watch Operation Guide 3529
Before Getting Started
This section provides an overview of the watch and introduces convenient ways
it can be used.
Watch Features Alarm
An alarm sounds whenever a time specified by you is reached. Timer Countdown
from a start time specified by you. An alarm sounds when the countdown reaches
zero. Stopwatch The stopwatch measures elapsed time in units of one second
(1/100 second for the first hour) up to 24 hours.
Note
The illustrations included in this operation guide have been created to
facilitate explanation. An illustration may differ somewhat from the item it
represents.
General Guide
ADay of the week BMonth, day CHour, minute, second
A button Pressing this button in any mode displays the setting screen.
B button Pressing this button in the Stopwatch Mode resets to all zeros.
C button Each press cycles between watch modes. Pressing this button after
performing operations in any mode returns to the Timekeeping Mode.
D button Pressing this button while any setting screen is displayed will
change the setting.
L button Press to turn on illumination.
Indicators
ADisplayed while an alarm is turned on.
BDisplayed while the hourly time signal is enabled.
CDisplayed while 24-hour timekeeping is being used.
DDisplayed during p.m. times while 12-hour timekeeping is being used.
EDisplayed while a split time measurement operation is in progress.
FDisplayed while Auto Repeat Timer is enabled.
GDisplayed while flash alert is enabled.
5
Watch Operation Guide 3529
Navigating Between Modes
Press (C) to cycle between modes. After performing operations in any mode,
press (C) to return to the Timekeeping Mode.
Timekeeping Mode
Time Adjustment
Use the procedures in this section to adjust the date and time settings.
3. Keep pressing (C) until the setting you want to change is flashing. Each
press of (C) moves the flashing to the next setting in the sequence shown
below.
Seconds
$ Stopwatch Mode
$ Alarm Mode
Timer Mode
$
$
Viewing the Face in the Dark
The watch has a light that illuminates the face for viewing in the dark.
Turning On Display Illumination Press (L) to turn on illumination.
Illumination will turn off automatically if an
alarm starts to sound.
Important!
Frequent use of illumination will run down the battery.
Adjusting the Current Time Setting
Use the procedures in this section to adjust the date and time settings.
Setting the Time/Date 1. Enter the Timekeeping Mode.
l Navigating Between Modes 2. Press (A).
This causes the seconds to flash.
Seconds
Hours
Minutes
Year
Month
Day
4. Configure the date and time settings. While the seconds are flashing,
pressing (D) will reset them to 00. 1 is added to the minutes when the current
seconds count is between 30 and 59 seconds. For all the other values, use (D)
to change the flashing setting. Holding down (D) scrolls through settings at
high speed.
5. Repeat steps 3 and 4 to select time and date settings.
6. Press (A) to complete the setting operation.
Note
While the setting is being configured, the watch will exit the setting
operation automatically after about two or three minutes of non-operation.
Note
Display illumination is disabled when any one of the conditions below exists.
Alarm, timer alert, or other beeper sounding
6
Watch Operation Guide 3529
Switching between 12-hour and 24hour Timekeeping
You can specify either 12-hour format or 24hour format for the time display.
1. Enter the Timekeeping Mode. l Navigating Between Modes
2. Press (A). This causes the seconds to flash.
Alarm
The watch will beep when an alarm time is reached. The hourly time signal
causes the watch to beep every hour on the hour.
3. Keep pressing (C) until the setting you want to change is flashing. Each
press of (C) moves the flashing to the next setting in the sequence shown
below.
Hours
Minutes
Seconds
3. Press (L) to select 12-hour or 24-hour timekeeping.
Each press of (L) toggles between 12hour and 24-hour timekeeping.
[P] is displayed during p.m. times while 12-hour timekeeping is being used.
12-hour timekeeping
24-hour timekeeping
4. Press (A) to complete the setting operation.
Note
While the setting is being configured, the watch will exit the setting
operation automatically after about two or three minutes of non-operation.
If flash alert is enabled, display illumination will flash along with the
alarm beeper and the hourly time signal. l Configuring Flash Alert Settings
Configuring Alarm Settings
There are various alarm variations, and the variation that is set depends on
the hour, minute, month, and day settings you configure. Configuring Some of
the Settings (hour,
minute, month, day) Hour and Minute Settings Only
The alarm sounds every day at the specified time. Month, Hour and Minute
Settings Only The alarm sounds every day of the specified month at the
specified time. Day, Hour and Minute Settings Only The alarm sounds every
month at the specified time on the specified day. All Settings: Hour, Minute,
Month, Day The alarm sounds once at the specified time on the specified date.
1. Enter the Alarm Mode. l Navigating Between Modes
2. Press (A). This causes the hours digits to flash.
Month
Day
4. Use (D) to change the value. Holding down (D) scrolls through settings at
high speed. [-] is displayed for the month and [- -] is displayed for the day
if nothing is specified for these settings. While you are setting the
timekeeping hour, [P] (p.m.) is displayed during p.m. times if you are using
12-hour timekeeping, while [24] is displayed if you are using 24-hour
timekeeping.
5. Repeat steps 3 and 4 to select time and date settings.
6. Press (A) to complete the setting operation.
Note
While the setting is being configured, the watch will exit the setting
operation automatically after about two or three minutes of non-operation.
Hours
7
Watch Operation Guide 3529
To stop the alarm To stop the alarm after it starts to sound when an alarm
time is reached, press any button.
Note
A beeper sounds for 20 seconds to let you know when the alarm time is reached.
If flash alert is enabled, display illumination flashes along with the alarm
beeper and the hourly time signal. Pressing any button to stop the alarm
beeper also stops the flash alert operation. l Configuring Flash Alert
Settings
Enabling/Disabling an Alarm or the Hourly Time Signal
1. Enter the Alarm Mode. l Navigating Between Modes
2. Press (D) to toggle the alarm or the hourly time signal between on and
off. Each press of (D) toggles the displayed (alarm) or (hourly time signal)
icon between on (displayed) and off (not displayed).
Alarm
Hourly time signal
Turning Off an Alarm or the Hourly Time Signal
To stop an alarm or the hourly time signal from sounding, perform the steps
below to turn it off. To have an alarm or hourly time signal
sound again, turn it back on.
1. Enter the Alarm Mode. l Navigating Between Modes
2. Press (D) to turn off the displayed alarm or the hourly time signal. Each
press of (D) toggles the displayed (alarm) or (hourly time signal) icon
between on (displayed) and off (not displayed).
Alarm
Alarm and hourly time signal off Alarm beeper only
Hourly time signal beeper only Alarm and hourly time signal on
Hourly time signal Alarm and hourly time signal off Alarm beeper only Hourly time signal beeper only Alarm and hourly time signal on
8
Watch Operation Guide 3529
Stopwatch
The stopwatch can measure elapsed time up to 23 hours, 59 minutes, 59 seconds
(24 hours). When this maximum limit is exceeded, elapsed time measurement
returns to 0 and timing continues from there.
Measuring Elapsed Time
1. Enter the Stopwatch Mode. l Navigating Between Modes
2. Use the operations below to measure elapsed time.
D Start
D Stop
D Resume
D Stop
Elapsed time is shown in 1/100-second units for the first hour of the
measurement. After the first hour, elapsed time is shown in one-second units.
First hour
After first hour
Measuring a Split Time
1. Enter the Stopwatch Mode. l Navigating Between Modes
2. Use the operations below to measure elapsed time.
Pressing (B) displays the elapsed time from the start of a race up to the
point when you pressed the button (split time).
D Start
B Split
B Split release
D Stop
Elapsed time is shown in 1/100-second units for the first hour of the
measurement. After the first hour, elapsed time is shown in one-second units.
First hour
After first hour
Minutes, seconds, 1/100 seconds
Hour, minute, second
3. Press (B) to reset the measurement time to all zeros.
Timing the First and Second Place Finishers
1. Enter the Stopwatch Mode. l Navigating Between Modes
2. Use the operations below to measure elapsed time.
D Start
B 1st Finisher*
D 2nd Finisher*
- This displays the time of the first finisher.
Elapsed time is shown in 1/100-second units for the first hour of the measurement. After the first hour, elapsed time is shown in one-second units.
First hour
After first hour
Minutes, seconds, 1/100 seconds
Hour, minute, second
3. Press (B) to display the time of the second place finisher.
4. Press (B) to reset the measurement time to all zeros.
Minutes, seconds, 1/100 seconds
Hour, minute, second
3. Press (B) to reset the measurement time to all zeros.
9
Watch Operation Guide 3529
Timer
The timer counts down from a start time specified by you. A beeper sounds when
the end of the countdown is reached.
If flash alert is enabled, display illumination flashes along with the beeper
at the end of the countdown. l Configuring Flash Alert Settings
Using a Timer Your watch provides you with two different types of timers.
Select the timer you want to suit your needs. Repeat Timer
With the Repeat Timer, countdown stops and the start time setting appears when
the end of the countdown is reached. The Repeat Timer comes in handy when you
need to perform the same countdown operation a number of times. Auto Repeat
Timer With Auto Repeat Timer, the countdown operation is automatically
restarted from the start time when the end of the countdown is reached. This
continues until you stop the countdown operation.
Setting the Time
The countdown start time can be set in 1second units up to 24 hours. If a
timer countdown operation is in
progress, reset the timer to its current start time before performing this
operation. l Using the Timer 1. Enter the Timer Mode.
l Navigating Between Modes 2. Press (A).
This causes the hours digits to flash.
Hours
3. Use (D) to change the timer hour setting. Holding down (D) scrolls through
settings at high speed.
4. Press (C). This causes the minutes digits to flash.
Minutes
5. Use (D) to change the timer minute setting.
6. Press (C). This causes the seconds digits to flash.
Seconds
7. Use (D) to change the timer seconds setting.
8. Press (L) to select Repeat Timer or Auto Repeat Timer. Each press of (L)
toggles between Repeat Timer and Auto Repeat Timer. [AUTO] is displayed while
Auto Repeat is enabled.
9. Press (A) to complete the setting operation.
Note While the setting is being configured,
the watch will exit the setting operation automatically after about two or
three minutes of non-operation. Setting a start time of [0:00’00] will perform
a countdown of 24 hours.
10
Watch Operation Guide 3529
Using the Timer
1. Enter the Timer Mode. l Navigating Between Modes
Hour, minute, second
2. Use the operations below to perform a timer operation.
D Start
(Countdown starts)
D Pause
D Resume
(Time up)
A beeper will sound for 10 seconds to let you know when the end of a countdown
is reached.
When using the auto-repeat timer with a countdown of 10 seconds or less, the
countdown end beeper will sound for only one second.
To reset a paused countdown to the start time, press (A).
3. Press any button to stop the tone.
Note
If flash alert is enabled, display illumination flashes along with the beeper
at the end of the countdown. Pressing any button to stop the alarm beeper also
stops the flash alert operation. l Configuring Flash Alert Settings
Other Settings
This section explains other watch settings you can configure.
Configuring Flash Alert Settings
If flash alert is enabled, display illumination will automatically flash along with the alarm, timer, and other beepers.
1. Enter the Timekeeping Mode. l Navigating Between Modes
2. Hold down (D) for at least two seconds to toggle flash alert between
enabled and disabled.
Flash alert toggles between on and off each time you hold down (D).
is displayed while flash alert is
enabled.
Other Information
This section provides non-operational information you also need to know. Refer
to this information as required.
Specifications
Accuracy at normal temperature : ±15 seconds a month
Timekeeping : Hour, minute, second, year, month, day, day of the week
a.m./p.m. (P)/24-hour (24) timekeeping Full Auto Calendar (2000 to 2099)
Year display on setting screen only.
Alarm : Time alarm Setting units: month, day, hour, minute Alarm beeper
duration: 20 seconds Hourly time signal: Beep every hour on the hour
Timer : Measuring unit: 1 second Countdown range: 24 hours Time setting unit:
1 second Auto Repeat 10-second beeper when the end of the countdown is reached
Stopwatch : Measurement units 1/100 seconds (first hour); 1 second (after
first hour) Measuring range 23 hours, 59 minutes, 59 seconds (24 hours)
Measurement Functions: Elapsed time, cumulative time, split times, 1st and 2nd
place finisher times
Other : Auto return, 12-/24-hour timekeeping, LED backlight (Super
Illuminator, afterglow), flash alert
Power Supply : CR2016 x 1 Battery life: Approximately 5 years Conditions:
Alarm: Once (20 seconds)/day (flash alert enabled) Illumination: Once (3.5
seconds)/day
Specifications are subject to change without notice.
11
Watch Operation Guide 3529
Troubleshooting
Alarm and Hourly Time Signal
Q1 An alarm and/or the hourly time signal do not sound.
Enable the alarm and/or the hourly time signal. l Configuring Alarm Settings l
Enabling/Disabling an Alarm or the Hourly
Time Signal
Other
Q1 I can’t find the information I need here.
Visit the website below. https://world.casio.com/support/
12
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>