ACCO BRANDS M01678-D 2.4G Wireless Mouse and Dongle

Product Information

• User Manual VER: 0.1
• Model Name: 2.4G Wireless Mouse & Dongle
• Model Number: M01678-D
• Version: 0.1
• Date: 2023.02.01
• Page Count: 9

product Electrical Specification

1. Operating Voltage:
   • Mouse supply voltage: 1.5V (1AA battery)
   • Dongle supply voltage: 5V (USB Port)
2. Current Consumption:
   • Current use: < 10mA
   • Dongle: < 35mA
3. Sleep Mode:
   • Electrical Current: 1mA;
   • Wake Up: Press any button
4. Mouse Pointer Performance:
   • Resolution: 400/800/1200/1600 DPI
   • Speed: 30 inches/sec Max
   • Acceleration: 10G
5. LED Indicating Functions:
   • When the battery power is low (battery voltage reduces to…

Product Usage Instructions

1. Insert the AA battery into the mouse.
2. Connect the dongle to a USB port on your computer.
3. Turn on the mouse using the power switch on the bottom of the mouse.
4. The LED light on the mouse will flash to indicate that it is searching for the dongle. Wait for the LED light to stop flashing.
5. Your mouse is now ready to use. Move it around to ensure that it is working properly.
6. To conserve battery life, turn off the mouse when not in use.

• Model NAME : 2.4G Wireless Mouse &Dongle
• MODEL NO. : M01678-D
• VERSION : 0.1
• DATE: 2023.02.01
  Version.

| Revised Date| PIC| Remark
---|---|---|---
0.1| 01/02/2023| Bob| Preliminary
 |  |  |
 |  |  |
 |  |  |
 |  |  |
 |  |  |
 |  |  |
 |  |  |

1. Operating Voltage:
   • Mouse supply voltage: 1.5V (1AA battery)
   • Dongle supply voltage: 5V (USB Port)
2. Current Consumption:
   • Current use: < 10mA
   • Dongle: < 35mA
3. Sleep Mode:
   • Electrical Current: 1mA;
   • Wake Up: Press any button
4. Mouse Pointer Performance:
   • Resolution: 400/800/1200/1600 DPI
   • Speed: 30 inches/sec Max
   • Acceleration: 10G
5. LED Indicating Functions:
   • When the battery power is low (battery voltage reduce to <1.0V) the LED will glisten at the frequency of 1Hz
6.  Wireless specifications
   • Mouse&Dongle: 2.403-2.480GHz frequency coverage.
   • GFSK RF transceiver
   • High Speed RF link data rate Max. 1M bit/s

Button Functions

1. Left Button: Mouse left button standard function
2. Right Button: Mouse right button standard function
3. Middle Button: Mouse middle button standard function
4. Wheel: Mouse scroll wheel standard function

Operation Process

• Step 1
  Open the battery cover in the back of the Mouse. Insert 1 AA battery which is environment-friendly and safe Close the battery cover.

• Step 2
  Place the mouse on a desk or other plane surface. The surface material isn’t metal is better for wireless distance.

• Step 3
  Insert the Dongle in a USB port of PC. The Transceiver is paired with the mouse.

• Step 4
  Use the mouse freely.

Caution

• Please use the Mouse in human houses only and keep away water.
• Children using the mouse with guardians together is necessary.
• Keep dry. Humidity, liquids, contain minerals that will corrode electronic circuits.
• Don’t use or store in dusty, dirty areas.
• Don’t store in hot areas. High temperatures can shorten the life of electronic devices and warp or melt certain plastics.
• Don’t store in very cold areas. Moisture can form inside the case, which may damage electronic circuit boards.
• Don’t attempt to open the case. Non-expert handling of the device may damage the system.
• Avoid dropping and strong impact.

FCC STATEMENT

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

RF warning statement:
The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:

1. this device may not cause interference, and
2. this device must accept any interference, including interference that may cause undesired operation of the device.”

To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. (Example- use only shielded interface cables when connecting to computer or peripheral devices). This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Caution!
The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user authority to operate the equipment.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>