ANSTEN K1 Bluetooth Headphone with Bluetooth Transmitter Charging User Manual
- June 11, 2024
- ANSTEN
Table of Contents
- ANSTEN K1 Bluetooth Headphone with Bluetooth Transmitter Charging
- Product Overview
- Package Contents
- Basic Operation
- Bluetooth Pairing and Connection
- AUX Wired Connection
- LED Indicator
- Charging
- TTS Tone
- Bluetooth transmitter charging base
- LED Indicator
- Charging
- Product Specification
- Attention and Q & A
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
ANSTEN K1 Bluetooth Headphone with Bluetooth Transmitter Charging
Product Overview
The K1 Bluetooth Headphone with Bluetooth Transmitter Charging Base is a wireless headphone that can be charged using a charging base. The headphone has a power button, a microphone, a volume control button, and an MFB (Multi Function Button). The charging base has a charging LED indicator, a charging port, a Micro USB charging port, a 3.5mm AUX port, and an optical input port.
Package Contents
- A. K1 Bluetooth Headphone x 1
- B. Micro USB Charging Cable x 1
- C. K1 Bluetooth Transmitter Charging Base x 1
- D. User Manual x 1
- E. 3.5mm AUX Cable x 1
- F. Optical Cable x 1
- G. RCA Cable x 1
Basic Operation
To turn on the headphone, switch the power button to the ON side. The headphone will enter pairing mode automatically. To turn off the headphone, switch the power button to the OFF side. To pause/play music, short press the MFB button. To redial the last phone call number, double press the MFB button. To answer a call, short press the MFB button when the call is coming. To hang up a call, short press the MFB button during the call.
Bluetooth Pairing and Connection
- A. Switch to ON side, the K1 will power on and enter pairing mode with Red and Blue LED flash alternately.
- B. Search and click to connect “K1” on your phone Bluetooth lists, LED turns to solid Blue LED after connected.
- C. Control to answer/hang up a call, music play/ pause, previous/ next song, volume up/ down etc through the MFB /Volume +/Volume- buttons
AUX Wired Connection
Plug one end of 3.5mm cable in the 3.5mm AUX interface of headphone, another end plug in phone or PC audio port. When the audio cable is plugged in using the AUX function, the headphone button has no function. The AUX function can also be used when the headphone battery has no power.
Notes:
- The buttons of headphone are invalid when AUX mode.
- AUX function could be work when battery out of power or item power off.
- Bluetooth function will power off when plug AUX cable.
- The headphone can not power on while plugged AUX cable, need to pull out the cable first then power on the headphone
LED Indicator
Charging
Please charge the K1 at once when the Red LED flash. Charging time about 2 hours. Blue LED turn on when full charged. Connection for charging
- Plug one end of micro USB cable to K1, an Car charger, power bank or PC etc )
- Use Charging Base for charging, connect Micro USB charging cable to Charging Base, place K1 Headphone on the Charging Base, Headphone’s Red LED is on when is charging, Blue LED turn on when is full charged. ( When K1 transmitter is power on and use as the Charging Base for charging, place K1 Headphone on the Charging Base, the K1 transmitter will power off with Red LED flash once)
Notes:
- Please charge the item at least once for every 2 months when without use.
- Charge when power on, it is normal for the Bluetooth indicator will overlapping with the charge indicator.
TTS Tone
Bluetooth transmitter charging base
Bluetooth transmitter operation
Binding device operation
- First, delete the pairing record. Double press the MFB in pairing mode ( Because there is only one pairing record to perform the binding operation).
- Pair and connect the binding device with K1.
- After successfully connect with the headphone, double-click the MFB to bind, and the blue LED flash 5 times after the binding is successful.
- Replace the binding device when there is a binding record. After delete the pairing record, bind the new device to K1 Transmitter after successful connection, then the bind device record can be replaced.
- After successfully binding the device information, K1 Transmitter automatically re-power on and reconnects to the device. Reboot can update the storage space and avoid new problems.
Bluetooth pairing and connection
- Plug in Micro USB charging cable to charging port, switch power button to ON side to power on.
- Enter pairing mode: Power on will enter pairing mode automatically; Unconnected standby mode or connected one device, long press MFB for 5 seconds to enter pairing mode.
- Turn on the Bluetooth headphone or Bluetooth speaker, enter pairing mode, place K1 Transmitter and the device close and wait for about 30 seconds, when Blue LED is on after connected
- Connect one end of 3.5mm AUX cable with K1, another end to phone or PC, the headphone or speaker can be heard music from phone or PC.
If to use optical cable connection, please plug in the Optical input port
Connection with Two Devices
- Follow 8.2 to connect with the first device, long press MFB button for 5 seconds to enter pairing mode (The first connected device will work well).
- Turn on the second device (Bluetooth headphone, speaker or receiver) enter pairing mode, place it close with K1 Transmitter and wait for 30 seconds, K1 will connect the second device. After the device is connected, you can hear music from it, this is the multi point connections. (The first device will have music issue when connect to second device, then it will be fine after few seconds)
Priority support aptX™ low latency for one connection (Connected device must support aptX™ low latency), support aptX™ low latency for two connections if two devices priority support aptX™ low latency, support aptX™ for two connections if two devices priority support aptX™, it will turn to SBC if two devices CODEC is not the same like one support aptX™ low latecy and another one support aptX™
LED Indicator
Charging
-
K1 Charging Base has no build-in battery, need power supply when use as bluetooth transmitter or charging for headphone.
-
Charging connection
Plug one end of micro USB cable to K1 Charging Base, another end to
USB charger (Car charger, power bank or PC etc ) -
When K1 transmitter is power on and use as the Charging Base for charging, place K1 Headphone on the Charging Base, the K1 transmitter will power off with Red LED flash once
-
Please cut off the power supply if not use
Product Specification
Headphone Specification
Notes: The actual using time will be different according to the ambient and music style.
Bluetooth Transmitter Charging Base Specification
Attention and Q & A
About K1 Headphone
- A. How to delete paired records? Power on , long press “Volume – & Volume +“ buttons for 5 seconds at the same time to delete paired records ( Red and Blue LED is on for 2 seconds at the same time). Pls try to delete paired records when have connection problems.
- B. What’s the password for pairing? Some devices require password for pairing, pls try 0000 (four zero), 8888 (four eight), 1111 (four one) or 1234 ( one two three four).
- C. Which devices could charge for the headphone? Any car charger, power bank, PC etc which meet DC 5V, charging current more than 400mA could be charge for this item. And K1 Charging Base.
- D. How to do if can not power or connection issue? Please try charging reset, when power on, plug charging cable to charge to reset and power off. (When power button switch to ON, reset will power on automatically; When power button switch to OFF, reset will not power on) Re-power on can use normally.
- E. Why the headphone power off automatically?
- K1 will power off under standby mode for over 10 minutes, or the battery
- voltage is less than 3.1V.
- F. Disconnect (Out of valid connection range)?
When headphone and transmitter are out of valid connection range, headphone will enter Linkloss mode (Indicator is still connected, headphone will reconnect last device every 15 seconds), will enter paring mode if reconnect fail for over 10 minutes
About K1 Bluetooth Transmitter Charging Base:
- A. About reconnect K1 can storage 4 devices information, and the excess will be replaced by new device information (Why store 4 units? Because K1 will reconnect to all paired devices after power on, and if there are too many, the reconnection time will be too long) K1 waiting time for re-connection is: if one device is paired, the re-connection time is about 10 seconds, and the reconnection time for two devices is 12 seconds; When there are pairing records, K1 will automatically connect to all connected devices every time when power on (but only 2 devices can be connected at the same time, and the bind device will be connected first and then to the last connected device)
- B. How to delete pairing record In paring mode, double press MFB to clear the device information. If have no binding device record, will enter paring mode automatically, If have binding device record, will enter reconnect mode
- C. How to select SPDIF/AUX The default power on status is optical mode, and it will automatically switch to AUX mode when the AUX audio cable is inserted.
- D. How to charge for the charging base The charging base has no build-in battery, need power supply when use as bluetooth transmitter or charging for headphone.
- E. How to do if can not power on or dead when connect?
Please try reset and power on, and delete the pairing record.
Customer Service Free user support
We offer telephone, email and live online support. Your email is guaranteed to
be replied to within 1 working day, and is normally responded to even faster
than that!
Ansten support site also provides complete step-by-step instructions and
answers to FAQ online.
Online Video User Guides
We have clear video user guides for most of our products, which you can find
on video sites. You can search on youtube: “Ansten TV headphone
Contact us:
Email: anstenusa@gmail.com
site: www.ansten.net
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>