Extron Cubby F55 Edge Mount Cable Installation Guide

June 11, 2024
Extron

Extron Cubby F55 Edge Mount Cable

Extron Cubby F55 Edge Mount Cable

The Extron Cable Cubby F55 Edge is an edge-mount cable access enclosure that integrates AV technology and power on the furniture surface. It is designed for configurable rooms that require semi permanent AV connectivity, control, and power. An integrated clamp system secures the enclosure to the furniture without requiring tools or cutting. This guide provides instructions for an experienced installer to install and connect the Extron Cable Cubby F55 Edge Cable Access Enclosure.
IMPORTANT: Go to www.extron.com for the product specifications.

Kit Contents

  • Cable Cubby F55 Edge
  • Pry Tool (2)
  • Flex55 Adapter Module (2)
  • Cable Grommet Plate (2)
  • ZipClip 100
  • ZipClip 200
  • ZipClip 400
  • Grommet Zip Ties (4)
  • Plugs (8)

Extron Cubby F55 Edge Mount Cable 1

Planning

Read the following information before installing the Cable Cubby F55 Edge.

Check with Local and State Regulations Before Starting the Installation:

  • Ensure that the planned installation complies with building and electrical codes.
  • Ensure that the planned installation complies with the Americans with Disabilities Act or other accessibility requirements.

Check All Parts and Equipment Before Installation:

  • Ensure that all parts are present in each kit.
  • Ensure that necessary tools and equipment are available for the installation.
    NOTE : Excess cabling may cause clearance issues. Use zip ties to secure under-table cabling to prevent accidental contact or entanglement (see Routing and Connecting Cables on page 9).

Application Example

The application diagram below shows a power, data, and video wiring setup from a laptop to a conference monitor. The setup is made simple by using the included Cable Cubby Flex55 Captive Cable Kit, installed in the Cable Cubby F55 Edge enclosure.

Extron Cubby F55 Edge Mount Cable 2

Preparing the Cable Cubby F55 Edge

Before installing the Cable Cubby F55 Edge, please check with Local and State Regulations. Also, check all parts and equipment before installation to ensure that everything is in good working order. Excess cabling may cause clearance issues, so use zip ties to secure under-table cabling to prevent accidental contact or entanglement. Refer to the Routing and Connecting Cables section on page 9 for more information.

Extron Cubby F55 Edge Mount Cable 3

Installing Modules into the Cable Cubby F55 Edge

The Cable Cubby F55 Edge can accommodate half- and full-size modules without removing the supports. Retractor modules can also be installed in any slot in the enclosure. To install a double-size Flex55 AC+USB 130 US Power Module, follow these steps:

  1. Plan and prepare the enclosure for module installation. For a double-size module installation, use pliers to carefully twist the desired bridge support back and forth until loose, and remove. Note that removal of a bridge support is irreversible.
  2. Install the cable grommet plate for cable pass-through applications.

Extron Cubby F55 Edge Mount Cable 4

Install the cable grommet plate for cable pass-through applications.

Extron Cubby F55 Edge Mount Cable 5 Extron
Cubby F55 Edge Mount Cable 6

Attaching an Optional ZipClip Mounting Device to the Cable Cubby F55 Edge

The ZipClip 100, 200, or 400 can be attached to the Cable Cubby F55 Edge in order to mount a power supply or other device to the Cable Cubby. Determine which ZipClip to use (depending on the device being attached) and in which orientation (vertical or horizontal). Note that the ZipClip 400 can be mounted horizontally only. Plan and ensure that there is ample space for the device and its cables.Extron Cubby F55 Edge Mount Cable 7

Attaching an Optional PMK 155 Mounting Kit
Follow these steps to attach a PMK 155 Mounting Kit to the Cable Cubby F55 Edge.

  1. The Cable Cubby F55 Edge is delivered with an accessory mounting bracket attached. Detach this bracket by removing its two mounting screws (see figure 8). Set the bracket and screws aside. You will reattach them in step 3.Extron Cubby F55 Edge Mount Cable 8
  2. Attach the PMK 155 to the accessory bracket using the two screws and washers from the PMK kit (see figure 9).Extron Cubby F55 Edge Mount Cable 9
  3. Attach the accessory bracket and PMK 155 to the Cable Cubby F55 Edge, using the two screws removed in step 1.Extron Cubby F55 Edge Mount Cable 10

Mounting the Cable Cubby F55 Edge to a Table

Mount the Cable Cubby F55 Edge on the edge of the table as shown below.

Extron Cubby F55 Edge Mount Cable 11

Routing and Connecting Cables
Organize and connect cables as shown in figure 12. Use zip ties (provided) to fasten the cables to the enclosure where needed.Extron Cubby F55 Edge Mount
Cable 12

Appendix — Removing Modules from the Cable Cubby F55 Edge

If the modules need to be replaced or removed from the Cable Cubby F55 Edge enclosure, the following diagrams show the procedure for removing modules with the provided pry tool. This process applies to any compatible Flex55 and EU module.
NOTE : To verify the location of the locking tabs, check the module specifications (available at www.extron.com ).

Extron Cubby F55 Edge Mount Cable 13Extron
Cubby F55 Edge Mount Cable 14

Installation Overview

  • Planning (see page 2)

    • Check with local and state regulations before starting the installation.
    • Check all parts and equipment before installation.
  • Preparing the Cable Cubby F55 Edge (see page 3)

    • Check the modules for compatibility and installation requirements.
  • Installing Modules into the Cable Cubby F55 Edge (see page 4)

    • Install half-, single-, and double-size modules into the Cable Cubby F55 Edge.
    • Remove any bridge supports if necessary. Note that removal of bridge supports is irreversible.
  • (Optional) Installing Retractor Modules (see the Cable Cubby F55 Edge Retractor Guide, provided with the Cable Cubby F55 Edge Retractor Bracket Kit)

    • Install Retractor modules in the Cable Cubby F55 Edge.
  • (Optional) Attaching a ZipClip (see page 6) or PMK 155 (see page 7) to the Cable Cubby F55 Edge

    • If using a ZipClip, determine which model to use (100, 200, or 400), and in which orientation (vertical or horizontal). Plan and ensure there is ample space for the device and its cables. or
      If using a PMK 155 , remove the accessory bracket from the Cable Cubby F55 Edge and attach the bracket to the PMK 155. Re-install the accessory bracket with the PMK to the Cable Cubby F55 Edge.

    • Attach the ZipClip or PMK 155 to the Cable Cubby F55 Edge.

    • Attach the desired power supply or other device to the ZipClip or PMK 155.

  • Mounting the Cable Cubby F55 Edge (see page 8)

    • Clamp and secure the Cable Cubby F55 Edge to the edge of the table.
  • Routing and Connecting Cables (see page 9)

    • Organize and connect the cables.
    • Use tie wraps to attach cables to the enclosure where needed.

For information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related topics, see the Extron Safety and Regulatory Compliance Guide on the Extron website.

© 2022 Extron — All rights reserved.www.extron.com
All trademarks mentioned are the property of their respective owners.
Worldwide Headquarters: Extron USA West, 1025 E. Ball Road, Anaheim, CA 92805, 800.633.9876

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals