BROAN BNAP-100 Smart Air Purifier Instruction Manual

BROAN BNAP-100 Smart Air Purifier

Product Information

The Smart Air Purifier (BNAP-100) is an intelligent air purifier that helps to purify the air in your home or office. It is ENERGY STAR certified and is measured based on a ratio between the model’s CADR for Smoke and the electrical energy it consumes, or CADR/Watt. The air purifier has Zero Ozone Emissions, which means that the measured Ozone Emissions from BNAP-100 during use phase does not exceed 0.005 ppm as tested by UL 867.

The air purifier is made in China to the quality standards and specifications of Broan-NuTone LLC, 926 West State Street, Hartford, Wisconsin, USA 53027. It conforms to UL std. 507 and is certified to CSA std. C22.2 NO. 187. The air purifier requires a 2.4 GHz Wi-Fi network and is app compatible with iOS and Android. For more information about the product, scan the QR code. The product comes with a warranty statement, service parts, technical support, and registration information.

Product Usage Instructions

Safety:
Before using the air purifier, always read, follow, and save all safety directions provided in the instruction manual.

Product Setup

1. Turn over the air purifier and remove the filter by rotating it counterclockwise until the two dots are aligned.
2. Take out the filter, remove the plastic covering, then take the adapter out before using. Put the filter back and rotate it clockwise until the arrow points to “on” with a click.
3. Place the air purifier on a firm, level floor with at least an 8 inch distance between the air inlets and walls or nearby furniture.
4. Connect the power adapter to the power port at the bottom of the unit. Then connect the power adapter to a power outlet.

How to Use
After setting up the air purifier, follow these steps to use it:

1. Press the power button on the control panel to turn on the air purifier.
2. The air purifier will automatically adjust to the optimal fan speed based on the air quality in the room.
3. If you want to manually adjust the fan speed, press the fan button on the control panel to cycle through the different fan speeds (low, medium, high).
4. The air purifier has a 3-in-1 filter with a pre-filter, HEPA filter, and activated carbon filter. The filter needs to be replaced every 6 months depending on usage.

App Connectivity
The air purifier can be connected to an app on your iOS or Android device. Follow these steps to connect:

1. Download and install the app from the App Store or Google Play Store.
2. Make sure your device is connected to a 2.4 GHz Wi-Fi network.
3. Open the app and follow the instructions to connect the air purifier to your Wi-Fi network.
4. Once connected, you can control the air purifier from your device, monitor air quality, and get filter replacement reminders.

Care & Maintenance
To keep your air purifier working effectively, follow these maintenance tips:

1. Replace the filter every 6 months depending on usage.
2. Clean the air inlet and outlet grills with a soft brush or vacuum cleaner every 3 months.
3. Do not wash the filter, as this can damage it.

Scan to download the App

Scan to view Quick Start Guide

Safety

This manual provides important safety messages regarding your electrical home appliance. Always read, follow, and save all safety directions.

General Information

• Only use your air purifier as described in this manual.
• Do not use without removing the plastic wrap from the filter. The purifier will not filter air, and may overheat, causing a fire hazard.
• Do not place or use your air purifier in the following locations:
  • Outdoors. For indoor use only.
  • On soft surfaces such as a bed or sofa as this could cause the unit to tip over.
  • Wet or damp locations, or excessively humid areas.
  • High-temperature locations, or near heat sources.
  • Places emitting oily smoke, such as kitchens.
  • Where oil or flammable gas is used, and there may be leakage.
  • Where combustible gases, vapors, metallic dust, aerosol (spray) products, or fumes from industrial oil are present.
  • Where the air outlet faces animals or plants.
• Keep 5 ft / 1.5 m away from where oxygen is being administered.
• Close supervision is necessary when the appliance is used by, on, or near children or persons not authorized to use it.
• Do not sit or place anything on the air purifier.
• Do not use your air purifier if it is damaged or not working correctly, or if the cord or plug is damaged. Do not try to repair it yourself.
• If you find abnormal conditions such as unusual noise, smell, smoke, temperature rise, leakage, etc., please turn off the power switch immediately, and then contact Customer Support for assistance.

Power and Cord

• Locate the air purifier near an electrical outlet and avoid using an extension cord.
• Keep the cord out of heavy traffic areas and arrange cord so that it will not be tripped over.
• Never place the cord near any heat source.
• Do not cover the cord with a rug, carpet, or other covering. Do not place the cord under furniture or appliances.
• Do not damage, break, forcefully bend, pull, twist, bundle, coat, pinch, or place heavy objects on the power cord.
• Remove the power adapter from the outlet when not in use.
• The power adapter of this air purifier uses standard US 120V, 60Hz outlets.

Compliance Information

FCC Notice
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to protect reasonably against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician to help.
• Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. ISED Compliance

Statement
This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s license-exempt RSS(s).
Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Broan-NuTone LLC is under license. Other trademarks and trade names are those of their respective owners. The energy efficiency of this ENERGY STAR certified model is measured based on a ratio between the model’s CADR for Smoke and the electrical energy it consumes, or CADR/Watt.

Zero Ozone Emissions – Measured Ozone Emissions from BNAP-100 Smart Air Purifier during use phase does not exceed 0.005 ppm as tested by UL 867.

Regulatory ID for BNAP-100 Smart Air Purifier

• FCC ID: 2ANDL-WBR3
• IC: 23243-WBR3
• EPA Est. No. 100879-CHN-1
• Air Purifier Ratings: 24 VDC, 1.7 A, 45 W
• Adapter Input: 100-240 V~ 50/60 Hz 1.5 A
• Adapter Output: 24 VDC, 2 A

Made in China to the quality standards and specifications of Broan-NuTone LLC, 926 West State Street, Hartford, Wisconsin, USA 53027
Broan-NuTone.com 800-558-1711

Product Overview

• Requires a 2.4 GHz Wi-Fi network. App compatible with iOS and Android.
• For more information about the product, scan the QR code.
• APPLE is a trademark of Apple Inc., registered in the U.S. and other countries.
• Android is a trademark of Google LLC.
  The Android robot is reproduced or modified from work created and shared by Google and used according to terms described in the Creative Commons 3.0 Attribution License.

Product Setup

Before using the air purifier, please remove the internal components and install the filter correctly according to the following instructions.

Note:
Make sure the air purifier is unplugged from the electrical outlet before installing the filters.

1. Turn over the purifier and remove the filter by rotating it counterclockwise until the two “ ” are aligned.
2. The power adapter is stored in the middle of the filter element inside the air purifier. Please take out the filter, remove plastic covering, then take the adapter out before using. Put the filter back and rotate it clockwise until the arrow points to “ ” with a click.
3. Place the air purifier on a firm, level floor. Make sure there is at least a 8-inch distance between the air inlets and walls or nearby furniture.
4. Connect the power adapter to the power port at the bottom of the unit. Then connect the power adapter to a power outlet.

How to Use

Air Quality Light Ring:
The air quality indicator on the Control Panel will change color depending on the air quality in the room, concerning the real time value of PM10, PM2.5, PM1 and TVOC.

Button Functionality

• Power Button
  Tap to turn the air purifier On – Off.

• Timer Button
  Tap repeatedly to set a 1-12 hour timer in one-hour intervals.

• Fan Speed Button
  Tap to select a fan speed from 1 to 5, or sleep mode. In sleep mode, the unit runs at speed 1 and all lights are off.

• Display Switch Button
  Tap repeatedly to change the currently displayed pollutant.
  Note:
  When the air purifier is switched on, it needs 20 seconds to show the PM value and 3 minutes to show the TVOC value. The displayed pollutant cycles through: PM10, PM2.5, PM1, TVOC.

• Filter Button
  Tap to check the remaining life percentage of the filter on the screen. Press and hold for 5s to reset the filter lifetime counter.

• Light Button
  Tap to select a brightness for all the lights on the control panel. It cycles through:

  • Normal – Dim – Off.

• Auto Button

  • Tap to turn Auto Mode On – Off.
  • Tap Speed button to exit Auto Mode.
    Note:
    Auto mode uses sensors inside the air purifier to adjust the fan speed automatically based on the ambient air quality.

• Wi-Fi Button
  Press and hold to configure the network connection.

• UV-C Button
  Tap to turn the UV function On – Off.

Memory Function
When the air purifier is plugged in, it will remember its programmed settings when turned off, and will resume these settings when turned back on.

Automatic Shutoff
As a safety feature, the UV function will automatically turn off if the filter is not in the right position.

App Connectivity

Steps:

• Download “Broan-NuTone Air Purifier” from your App store or scan QR code to the right.
• Press and hold the Wi-Fi button for 5 seconds until Wi-Fi icon blinks to enter into pairing mode.
• Follow the instructions on your phone to finish the configuration.

Additional App Features

1. Child lock function could be activated on your App. Power button on control panel still works even if the unit is in the state of locking.
2. The air purifier could be operated muted by touching the “Mute” button on App.

Care & Maintenance

• Always unplug before cleaning or maintaining the unit.
• Do not immerse unit in water or any other liquid.
• Do not use abrasive, corrosive or flammable products to clean any parts of the unit.
• The filters CANNOT be washed.

Clean the Air Purifier
Regularly clean the inside and outside of the air purifier to prevent dust from collecting.

• Use a soft, dry cloth to clean both the interior and exterior of the air purifier.
• Use a soft brush or cloth to clean the inlet and outlet of the air purifier.

Filter Change Reminder
When “ ” flashes, it is time to change your filter. The air purifier will comprehensively consider various parameters to calculate the remaining life of your filter. Under normal usage condition, the filter lifetime is around 6 months. Watch out for the signs of an expired filter, even if indicator does not flash:

• Increased noise when the air purifier is on
• Decreased airflow
• Unusual odors
• Visibly clogged filter

Replacing the Filter

1. Please make sure the air purifier is unplugged from the electrical outlet before installing the filters.
2. Unwrap the new filter from its plastic packaging.
3. Follow the steps in the Product Setup section.
4. Press and hold “ ” for 5 seconds to reset the filter.

Replacement Parts

• BNAP-100F: Smart Air Purifier Filter
• BNAP-100PS: Smart Air Purifier Power Adapter

References

• Broan-NuTone | Better Air. Better Life.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>