CamPark RC02 Rearview Monitor Kit User Manual

CamPark RC02 Rearview Monitor Kit

INTRODUCING

Thanks for purchasing backup camera! With this manual, you will be able to properly install and operate the unit. Please read this manual thoroughly before operating the unit.And keep it for further reference.

If you have any other questions or problems, Please feel free to contact us at

• DC@yooomail.com

We have professional team at your service, and your satisfaction is guaranteed.

BUTTON AND FUNCTIONS

1. Channel switch

2. Rotation image left/right/up/down

3. MENU

4. Decrease button for adjusting the value in menus.

5. Increase the button-for adjusting value in menus.

6. Power: Turn On/Off the monitor

7. IRWindow

8. Power: Turn On/Off the device.

9. Video Channel Switch

10. VOL+: Increase level

11. MENU

12. VOL-: decrease level

13. Mode: Rotation image left/right/up/down

14. Sun-visor

15. Rotation screw

16. IR LEDs

17. Metal housing

18. bracket

19. Lens

DEVICE PARAMETER

Monitor

• Screen size: 7 inch (16:9)
• Resolution: 1024×600
• System: PAL&NTSC
• Trigger wire for auto reversing
• Power: 11V-32V
• Power Consumption: 6W
• Operate mode: Button operation / remote control
• Work temp.: -10°C-+40°C
• Storage temp.: -25°C-+80°C
• External dimensions: 172LX119HX20W (mm)

Camera

• Image Sensors: Color CMOS Camera
• TV System: PAL / NTSC
• Waterproof rate: IP6 7
• Resolution: 1080P
• Minimum Illumination: 0.1Lux / F1.2 (0Lux with IR LEDs ON) Pin Lens: f=2.5mm
• Lens Angle: 120°
• IR LEDs: 18pcs
• Vertical Sync: Frequency: 50Hz / 60Hz
• Video Output: 1.0vp-p, 75Ohm
• Power Supply: 11V-32V
• Current Consumption: ,,;3oomA
• Electronic Shutter: 1/60 – 1/10,000 Seconds
• Operating Temperature: -20°C-70°C ,RH95% MAX
• Storage Temperature: -40°C-85°C ,RH95% MAX

CONNECTION DIAGRAM

1. Connect the power cord to car power: RED lead to car ACC power positive. Black lead to Ground. Green lead to the reverse light positive lead.
2. Connect the power cord to the 15m extension cable.
3. Route the extension cable to the end of your car.
4. Install the rearview camera on your car and connect the extension cable, then covered connector by rubber cover on cable
5. Route the excess cable.
6. Now when you put your car in Reverse Gear, the camera and the monitor automatically turn on and display the rear image.
7. When you are out of Reverse Gear, the camera and the monitor will automatically turn off.

NOTICE:

• The monitor can also be powered with the included cigarette lighter power adapter, however, if you installed it that way, the monitor will not be triggered by reversing, need to be manually turned on or turned off.
• The monitor will automatically turn on when you are in reversing and will turn off if not.

MONITOR AND CAMERA DIMENSION

PACKAGE CONTENTS

Menu

1. Brightness

   • Option: 0 – 100 Adjust image brightness

2. Contrast

   • Option: 0 – 100 Adjust image contrast

3. Saturation

   • Option: 0 – 100 Adjust the saturation of an image

4. Tint

   • Option: 0 – 100 Adjust image tone

5. Rotate

   • Flip image left/right/down/up

6. Car line1

   • Set a reversing line

7. Car line2

   • Set reversing line for V2

8. Car line

   • Reserved port

9. Car delay
   Set the delay to display the rear camera screen. It needs to be wired in the fuse box of the car battery before it can be used.

10. Auto reverse

11. Language

    • language setting

12. Reset Restore to factory settings

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>