Kolegend B0BD7S7541 3 in 1 Remote Control Excavator Toy User Guide

Kolegend B0BD7S7541 3-in-1 Remote Control Excavator Toy

BATTERY PRECAUTIONS

1.  The car is equipped with 7.2V rechargeable battery pack; the remote control is equipped with two 1.5V “AA” batteries;
2. The battery shall be removed and loaded correctly according to the polarity and voltage marks on the toy battery box; the battery shall not be short-circuited;
3. Non-rechargeable batteries cannot be charged;
4. Rechargeable batteries must be charged under adult supervision;
5. The rechargeable battery shall be removed from the toy before charging;
6. Different types of batteries or old and new batteries cannot be mixed;
7. Only batteries that are the same as or equivalent to the recommended batteries can be used,
8. The exhausted battery shall be removed from the toy. If the toy is not used for a long time, please remove the battery from the toy;
9. The power terminals must not be short-circuited;
10. The battery charging time is about 3-4 hours;
11. It cannot be tnnnected to more than the recmnmended amount of Vmver sources.
12. During the use Of the USB charging cable, check its wires, plugs, shells and other components regularly for damage. If damage is found, stop using it until the repair is complete.

CAUTION
This is not intended for use by year 8 children. please read the manual carefully and thoroughly before operating this product. Specifications and colors of contents may vary from photo.

FUNCTION INTRODUCTION OF REMOTE CONTROL

INSTALLATION INSTRUCTIONS FOR REMOTE CONTROL BATTERY

1. Loosen the battery cover screw with a screwdriver and remove the battery cover.
2. Load two 1 5V “AA’ batteries (batteries shall be purchased separately) into the battery box at the bottom of the remote control according to the correct polarity
3. Close the battery cover and tighten the screws.

SAFETY INSTRUCTIONS OF BATTERY

1. Remove and load the battery in the cnrrect way;
2. Non-rechargeable batteries cannot charged;
3. Rechargeable batteries must be charged under adult supervision;
4. Different types of batteries or old and new batteries cannot be mixed;
5. Only batteries that are the same as or equivalent to the recommended batteries can be used;
6. The rechargeable battery shall be removed from the model before charging;
7. The battery shall be loaded with the correct polarity;
8. The exhausted battery shall be removed from the model;
9. The power terminals must not be short-circuited;

Note: The battery shall be inserted with the correct polarity.

EXCAVATOR BATTERY INSTALLATION

1. Twist the battery cover latch to remove the battery cover.
2. Connect the rechargeable battery pack to the power port of the demolition machine closely and put it into the battery box.
3. Install the battery cover and twist the battery cover latch, then the battery installation is complete.

BATTERY CHARGING INSTRUCTIONS

CHARGING METHOD

Connect the rechargeable battery pack port to the USB charging port as shown in the figure, and make sure that the port connection is tight and correct, and then plug the USB into the power adapter to charge.

The status of the USB indicator light when charging:

1. The LED light is always on when connected;
2. The LED light flashes slowly when charging;
3. The LED light is off when fully charged;

Charging time: 3-4 hours
When the battery is fully charged, please unplug the USB charging cable in time.

FREQUENCY PAIRING AND POWER ON OF REMOTE CONTROL

The product is remotely controlled with 2.4GHz frequency For the first operation, the user must install the battery on the vehicle body and the remote control first, then make sure to power on, turn on the power to pair the frequency automatically. When the indicator light of the remote control stops flashing, the vehicle will make a “tick” sound, that is, the frequency pairing is completed. If the vehicle does not respond to the remote control, the user can turn off the power of remote control and vehicle, turn on the power of remote control and vehicle again to match again (same steps as above)

PARTS REPLACEMENT

1. Remove the fixing screws of bucket (Fig. 1) first, and then remove the bucket (Fig. 2)
2. Install the parts on the middle arm, insert the screw spikes and tighten the nuts

OPERATING INSTRUCTIONS OF EXCAVATOR

OPERATING INSTRUCTIONS OF DEMOLITION MACHINE

OPERATING INSTRUCTIONS OF LOG GRAPPLE

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>