BOSCH SMS6ZDI48E Dishwasher Instruction Manual
- June 11, 2024
- Bosch
Table of Contents
BOSCH SMS6ZDI48E Dishwasher
Product Information
The SMS6ZDI48E is a dishwasher that comes with a variety of features and settings to make dishwashing convenient and efficient. It has a button lock to prevent accidental button presses, can be controlled through Home Connect, has a filter system, and comes with a warranty.
Product Usage Instructions
Starting the programme: To start a dishwashing cycle, select the desired programme using the control panel and press the start button. The appliance will begin running the selected programme.
Activating button lock: To activate the button lock, press and hold the “Start” button for 5 seconds. The button lock symbol will appear on the display when it is activated.
Deactivate button lock: To deactivate the button lock, press and hold the
“Start” button for 5 seconds. The button lock symbol will disappear from the
display when it is
deactivated.
Interrupting programme: To interrupt a programme, press the “Start” button once. The programme will pause and the “Start” button will flash. To resume the programme, press the “Start” button again.
Terminate programme: To terminate a programme, press and hold the “Start” button for 3 seconds. The appliance will stop running the programme.
Switching off appliance: To switch off the appliance, press and hold the “On/Off” button for 3 seconds. The appliance will turn off.
Basic settings: The appliance has basic settings that can be changed. To
access these settings, press and hold the “Start” button and “Programme”
button simultaneously for 3
seconds. Use the control panel to navigate through the settings an change them
as desired.
Cleaning and servicing: To clean the tub, use a cleaning product specifically designed for dishwashers. To clean the filter system, remove the filters and rinse them under running water. Use a cleaning spray to clean the spray arms. Refer to the user manual for more detailed instructions on cleaning and servicing.
Troubleshooting: If you encounter any issues with the appliance, refer to
the troubleshooting section of the user manual. This section provides
information on error codes,
washing results, and malfunctions. If the issue cannot be resolved, contact
customer service.
Transportation, storage and disposal: If you need to transport or store the appliance, refer to the user manual for instructions. To dispose of the appliance, follow local regulations and guidelines.
Safety: To prevent injury or harm, always follow the safety instructions
provided in the user manual. Only use detergent and rinse aid products as
directed on their
packaging. Never equip the appliance with an external switching device or
tamper with the electrical installation.
Dishwasher
SMS6ZDI48E [en] Information for Use
Safety
Observe the following safety instructions. General information ¡ Read this
instruction manual carefully. ¡ Keep the instruction manual and the product
information safe
for future reference or for the next owner. ¡ Do not connect the appliance if
it has been damaged in transit. Intended use Only use this appliance: ¡ For
cleaning household tableware. ¡ In private households and in enclosed spaces
in a domestic en- Up to an altitude of 2500 m above sea level. Restriction on
user group This appliance may be used by children aged 8 or over and by people
who have reduced physical, sensory or mental abilities or inadequate
experience and/or knowledge, provided that they are supervised or have been
instructed on how to use the appliance safely and have understood the
resulting dangers. Do not let children play with the appliance. Cleaning and
user maintenance must not be performed by children unless they are being
supervised. Keep children under the age of 8 years away from the appliance and
power cable. Safe installation
WARNING Risk of injury! Improper installation may cause injury. When
installing and connecting the appliance, follow the in-
structions in the manual and installation instructions.
4
Safetyen
WARNING Risk of electric shock! ¡ Incorrect installation is dangerous.
Connect and operate the appliance only in accordance with the specifications
on the rating plate.
Always use the supplied power cable for the new appliance. Connect the
appliance to a power supply with alternating
current only via a properly installed socket with earthing. The protective
conductor system of the domestic electrical
installation must be properly installed. Never equip the appliance with an
external switching
device, e.g. a timer or remote control. When the appliance is installed, the
mains plug of the
power cord must be freely accessible. If free access is not possible, an all-
pole isolating switch must be installed in the permanent electrical
installation according to the installation regulations. When installing the
appliance, check that the power cable is not trapped or damaged. ¡ Cutting
through the supply hose or immersing the Aqua-Stop valve in water is
dangerous. Never immerse the plastic housing in water. The plastic housing on
the supply hose contains an electric valve. Never cut through the supply hose.
The supply hose contains electric power cables. WARNING Risk of fire! ¡ It is
dangerous to use an extended power cord and non-approved adapters. Do not use
extension cables or multiple socket strips. Only use adapters and power cords
approved by the manufacturer. If the power cord is too short and a longer one
is not available, please contact an electrician to have the domestic
installation adapted.
5
Safety
¡ Contact between the appliance and installation lines may lead to a defect in
these lines, e.g. gas pipes and power lines. Gas from a corroded gas pipe can
ignite. A damaged power line can cause a short circuit. Check that there is a
distance of at least 5 cm between the appliance and installation lines.
WARNING Risk of burns! If the appliance is not installed properly, this may
result in burns. With free-standing appliances, ensure that they are installed
with the back panel against a wall.
Safe use WARNING Risk of serious harm to health! Failure to comply with safety
instructions and directions for use on packagings of detergent and rinse aid
products may cause serious harm to health. Follow the safety instructions and
directions for use on the packagings of detergent and rinse aid products.
WARNING Risk of explosion!
¡ Adding solvents to the interior of the appliance may cause explosions. Never
add solvents to the interior of the appliance.
¡ Highly caustic alkaline or highly acidic cleaning agents in conjunction with
aluminium parts in the interior of the appliance may cause explosions. Never
use highly caustic alkaline or highly acidic cleaning agents, in particular
commercial or industrial products, in conjunction with aluminium parts (e.g.
grease filters of extractor hoods or aluminium pans), e.g. for the Machine
Care programme.
Safety
WARNING Risk of injury! ¡ Leaving the appliance door open may result in
injury.
Only open the appliance door to load or unload tableware in order to prevent
accidents, e.g. through tripping.
Do not sit or stand on the appliance door when open. ¡ Knives and utensils
with sharp points can cause injuries.
Arrange knives and utensils with sharp points in the cutlery basket with the
points downwards, on the knife shelf or in the cutlery drawer.
WARNING Risk of scalding! If you open the appliance door while the programme
is running, hot water may splash out of the appliance. Open the appliance door
carefully if the programme is still running. WARNING Risk of tipping!
Overfilling the Baskets may cause the appliance to tip up. Never overfill the
Baskets with free-standing appliances. WARNING Risk of electric shock! ¡ An
ingress of moisture can cause an electric shock. Only use the appliance in
enclosed spaces. Never expose the appliance to intense heat or humidity. Do
not use steam- or high-pressure cleaners to clean the
appliance. ¡ If the insulation of the power cord is damaged, this is danger-
ous. Never let the power cord come into contact with hot appli-
ance parts or heat sources. Never let the power cord come into contact with
sharp
points or edges. Never kink, crush or modify the power cord. WARNING Risk of
burns! The blow opening of the Zeolith container becomes hot and can cause
burns. Never touch the blow opening of the Zeolith container.
7
Safety
Damaged appliance WARNING Risk of electric shock!
¡ If the appliance or the power cord is damaged, this is dangerous. Never
operate a damaged appliance. Never operate an appliance with a cracked or
fractured surface. Never pull on the power cord to unplug the appliance.
Always unplug the appliance at the mains. If the appliance or the power cord
is damaged, immediately unplug the power cord or switch off the fuse in the
fuse box and turn off the water tap. “Call customer services.” Page 58
¡ Incorrect repairs are dangerous. Repairs to the appliance should only be
carried out by trained specialist staff. Only use genuine spare parts when
repairing the appliance. If the power cord of this appliance is damaged, it
must be replaced with a special connection cable, which is available from the
manufacturer or his Customer Service.
Risk to children WARNING Risk of suffocation!
¡ Children may put packaging material over their heads or wrap themselves up
in it and suffocate. Keep packaging material away from children. Do not let
children play with packaging material.
¡ Children may breathe in or swallow small parts, causing them to suffocate.
Keep small parts away from children. Do not let children play with small
parts.
¡ Children may become trapped in the appliance and suffocate. Use the
childproof lock if fitted. Never let children play with or operate the
appliance.
8
Safety
WARNING Risk of harm to health! Children can lock themselves in the appliance,
thereby putting their lives at risk. With redundant appliances, unplug the
power cord. Then
cut through the cord and damage the lock on the appliance door beyond repair
so that the appliance door will no longer close. WARNING Risk of crushing!
With higher-level appliances, children can become crushed between the
appliance door and cabinet doors underneath. Keep an eye on children when
opening and closing the appliance door. WARNING Risk of chemical burns! Rinse
aid and detergent may cause chemical burns to the mouth, throat and eyes. Keep
children away from detergent and rinse aid products. Keep children away from
the appliance when open. The water in the interior of the dishwasher is not
drinking water. It may contain residues of detergents and rinse aid. WARNING
Risk of injury! Children may get their fingers caught in the slots of the
tablet collecting tray and injure themselves. Keep children away from the
appliance when open.
9
Preventing material damage
Preventing material dam- Preventingmaterialdamage age
Preventing material damage
Safe installation
ATTENTION! ¡ Improper installation of the appli-
ance may cause damage. If the dishwasher is installed
above or below other domestic appliances, follow the information on
installation in combination with a dishwasher in the installation instructions
for the individual appliances. If there is no information or if the
installation instructions do not include the relevant information, contact the
manufacturer of these appliances to check that the dishwasher can be installed
above or below these appliances. If no information is available from the
manufacturer, the dishwasher should not be installed above or below such
appliances. To ensure the safe operation of all domestic appliances, continue
following the installation instructions for the dishwasher. Do not install the
dishwasher under a hob. Do not install the dishwasher near heat sources, e.g.
radiators, heat storage tanks, ovens or other appliances that generate heat. ¡
Contact between the appliance and water pipes may lead to corrosion of these
pipes, possibly causing them to leak. Check that there is a distance of at
least 5 cm between the appliance and the water pipe. The
10
pipes supplied for the drinking water and waste water connections are not
affected here. ¡ Modified or damaged water hoses may result in material damage
and damage to the appliance. Never kink, crush, modify or cut through water
hoses. Only use the water hoses supplied with the appliance or genuine spare
hoses. Never re-use water hoses that have been used before. ¡ If the water
pressure is too high or too low, the appliance may not be able to operate
properly. Make sure that the water pressure in the water supply system is min.
50 kPa (0.5 bar) and max. 1000 kPa (10 bar). If the water pressure exceeds the
maximum value specified, a pressure-reducing valve must be installed between
the drinking water connection and the hose set of the appliance.
Safe use
ATTENTION! ¡ Escaping water vapour can dam-
age fitted units. When the programme ends,
leave the appliance to cool down for a while before opening the door. ¡
Special salt for dishwashers can damage the tub due to corrosion. To make sure
that any special salt that escapes is washed out of the tub, add the special
salt to the dispenser for special salt immediately before the programme
starts. ¡ Detergent may damage the water softening system. Only fill the
dispenser of the water softening system with special dishwasher salt.
Environmental protection and saving energy
Unsuitable cleaning agents may damage the appliance. Do not use a steam cleaner. So as not to scratch the finish on the appliance, do not use sponges with a rough surface or abrasive cleaning agents. To prevent corrosion, do not use sponge cloths on dishwashers with a stainless steel front or rinse such cloths thoroughly several times before using them for the first time. Environmental protection Environmentalprotectionandsavingenergy and saving energy Environmental protection and saving energy
Disposing of packaging
The packaging materials are environmentally compatible and can be recycled.
Sort the individual components by
type and dispose of them separately.
Saving energy
If you follow these instructions, your appliance will use less electricity and
less water. Use the Eco 50 ° programme.
The Eco 50 ° programme is energy-efficient and environmentally friendly.
“Programmes”, Page 18 Change the sensor setting to the default. Consumption is
reduced. “Sensors”, Page 12
Zeolith drying automatically helps to save energy.
“Zeolith drying “, Page 11
Zeolith drying
The appliance features a Zeolith container. Zeolith drying lets you save
energy. Zeolite is a mineral that can store moisture and heat energy and then
release them again. During dishwashing heat energy is used to heat up the
washing water and dry the mineral. During the drying phase moisture from the
interior of the dishwasher is stored in the mineral and heat energy is
released. The heat energy is blown out into the interior of the dishwasher
with dry air. This speeds up and improves drying. Zeolith drying therefore
saves a great deal of energy. Tip: To avoid impairing Zeolith drying
performance, do not position tableware parts directly in front of the intake
opening or the blow opening of the Zeolith container. Do not position heat-
sensitive tableware parts directly in front of the blow opening of the Zeolith
container. “Appliance”, Page 14
AquaSensor
The AquaSensor is an optical measuring device (light barrier) which measures
the turbidity of the rinsing water. You can save water with the AquaSensor.
Use of the AquaSensor depends on the programme. If the soiling level is high,
the rinsing water is drained off and replaced with fresh water. If the soiling
level is lower, the rinsing water is used in the next wash cycle, so reducing
water consumption by 3-6
11
enInstallation and connection
litres. In the automatic programmes the temperature and run time are additionally adjusted to the level of soiling.
Sensors
The sensors adjust the programme sequence and strength in the automatic programmes depending on the level and type of soiling. The sensor has different sensitivity settings that can be changed in the basic settings.
Sensor setting SE:00 SE:01
SE:02
Description Optimum setting for a mixed load and heavily soiled tableware. Saves both energy and water. Adjusts the programme strength for effective removal of food remnants even with low soiling levels. Energy and water consumption are adjusted accordingly. Adjusts the programme strength for difficult conditions of use, e.g. stubborn dried-on food remnants. Recommended setting when using organic or ecological detergents containing low levels of active agents. Energy and water consumption are adjusted accordingly.
Installation and connec- Installationandconnection tion
To ensure proper operation, connect Installationandconnection the appliance to
the power and water supply correctly. Observe the specified criteria and the
installation instructions.
Scope of supply
After unpacking all parts, check for any damage in transit and completeness of
the delivery. If you have any complaints, contact the dealer who sold you the
appliance or our Customer Service. Note: The appliance has been tested at the
factory to check it is in working order. It is possible that water has left
marks on the appliance. These marks will disappear after the first wash cycle.
The delivery consists of the following: ¡ Dishwasher ¡ Operating instructions
¡ Installation Instructions ¡ Further information documents ¡ Installation
material ¡ Salt filling aid funnel ¡ Mains cable ¡ Quick reference guide
Installing and connecting the appliance
You can position your built-under or integrable appliance in a fitted kitchen
between wooden and plastic walls. If you subsequently install your dishwasher
as a free-standing appliance, you must stop it from tipping over, e.g. by
screwing it to the wall or
12
installing it under a continuous worktop that is securely connected to
adjacent cabinets. 1. “Follow the safety instructions.”
Page 4 2. “Follow the instructions for elec-
trical connection.” Page 13 3. Check the Scope of supply and
the condition of the appliance. 4. Consult the installation instructions
for the installation dimensions required. 5. Make the appliance level using
the height-adjustable feet. Make sure that the appliance is standing on the
floor securely. 6. “Install the drainage connection.” Page 13 7. “Install the
drinking water connection.” Page 13 8. Connect the appliance to the power
supply.
Drainage connection
Connect your appliance to drainage connection so dirty water is discharged via
the wash cycle.
Installing the drainage connection 1. Consult the installation instructions
supplied for the steps required here. 2. Connect the wastewater hose to the
outlet connection of the siphon using the enclosed parts. 3. When doing so,
check that the wastewater hose is not kinked, crushed or twisted. 4. Also
check that there is no cover in the drainage system preventing the wastewater
from being discharged.
Installation and connection
Drinking water connection
Connect your appliance to a drinking water connection. Installing the drinking
water connection Note ¡ If you are replacing the appliance,
you must use a new water supply hose. 1. Consult the installation instructions
supplied for the steps required here. 2. Connect the appliance to the drinking
water connection using the enclosed parts. Observe the “Technical data” Page
59. 3. When doing so, check that the drinking water connection is not kinked,
crushed or twisted.
Electrical connection
Connecting the appliance to the electricity supply Notes ¡ Please follow the
“Safety instruc-
tions” Page 4. ¡ Connect the appliance to alternat-
ing current only, in the range of 220 – 240 V and 50 Hz or 60 Hz. ¡ Please
note that the water safety system is only functional if there is a power
supply. 1. Insert the non-heating appliance plug of the power cable into the
appliance. 2. Insert the mains plug of the appliance into a nearby socket. The
connection data for the appliance can be found on the rating plate. 3. Check
that the mains plug is inserted properly.
13
enFamiliarising yourself with your appliance
Familiarising yourself with your appliance
Familiarisingyourselfwithyourappliance
Familiarising yourself with your appliance
Appliance
You can find an overview of the parts of your appliance here.
8
9
7
6
10
11
5
12
4
13
3 14
2
15
1
1
Rating plate
Rating plate with “E number and FD number” Page 59. The data you need for “Customer Service” Page 58.
1 Depending on the appliance specifications
14
Familiarising yourself with your applianceen
2
Detergent dispenser
“Detergent” Page 29 is added to the detergent dispenser.
3
Bottom basket
“Bottom basket” Page 22
4
Dispenser for special salt
Add special salt to the dispenser for special salt. “Water softening system”, Page 26
5
Lower spray arm
The lower spray arm washes the tableware in the bottom basket. If the tableware has not been washed properly, clean the spray arms. “Cleaning spray arms”, Page 43
6
Tablet collecting tray
During the wash cycle tablets automatically fall out of the detergent dispenser into the tablet collecting tray where they can fully dissolve.
7
Top basket
“Top basket” Page 21
8
3rd basket
“3rd basket” Page 23
9
Cutlery shelf1
“Cutlery shelf” Page 23
10 Upper spray arm
The upper spray arm washes the tableware in the top basket. If the tableware has not been washed properly, clean the spray arms. “Cleaning spray arms”, Page 43
11
Intake opening of the Zeolith con- The intake opening is required for “Zeolith drying”
tainer
Page 11.
12
Blow opening of the Zeolith con- The blow opening is required for “Zeolith drying ”
tainer
Page 11.
13 Filter system
“Filter system” Page 42
14 Cutlery basket
“Cutlery basket” Page 22
15 Dispenser for rinse aid
Add rinse aid to the dispenser for rinse aid. “Rinse aid system”, Page 28
1 Depending on the appliance specifications
Controls
You can use the control panel to configure all functions of your appliance and
to obtain information about the operating status. With some buttons you can
perform different functions.
15
enFamiliarising yourself with your appliance
1 2 34
56 7
14 13 12 11 10 9 8
1
ON/OFF button and reset button
“Switching on the appliance” Page 34 “Switching off the appliance” Page 35
“Terminating the programme” Page 35
2
Programme buttons
“Programmes” Page 18
3
Programme sequence display
The programme sequence display shows the current cycle of the appliance, e.g. washing, rinsing or drying.
4
Display
The display shows information about progress of the programme, the remaining running time or the basic settings. You can change the basic settings via the display and the setting buttons. “Changing basic settings”, Page 38
5
Timer programming and setting but- “Setting timer programming” Page 34
tons
“Changing basic settings” Page 38
6
Remote Start
“Remote Start “, Page 39
7
Start button
“Starting the programme” Page 35
8
Programme buttons and additional functions
Programmes “Programmes”, Page 18
Additional functions
“Additional functions”, Page 20
9
button
If you press
for approx. 3 seconds,
you can open the basic settings.
“Changing basic settings”, Page 38
10 WLAN display
“Home Connect” Page 38
1 Depending on the appliance specifications
16
Familiarising yourself with your applianceen
11 Rinse aid refill indicator
12 Water supply display 13 Special salt refill indicator
14 Door handle1
1 Depending on the appliance specifications
Rinse aid system “Adding rinse aid”, Page 28 Display for water supply
Water softening system “Adding special salt”, Page 27 Open the appliance door.
17
enProgrammes
Programmes Programmes
You Programmes can find an overview of the programmes that can be selected here. Different programmes, which can be found on the control panel of your appliance, are available depending on the appliance configuration. The running time may vary depending on the programme selected. The running time depends on the water temperature, the quantity of tableware, the level of soiling and the additional function selected. The
runtime will change if the rinse aid system is switched off or rinse aid needs to be added. The consumption values can be found in the quick reference guide. The consumption values relate to normal conditions and a water hardness of 16 – 20 °E. Different influencing factors such as water temperature or pipe pressure may result in deviations.
Programme: Intensive 70°
Auto 45-65° Eco 50°
Use
Programme sequence Additional func-
tions
Tableware:
Intensive:
¡ Washing pots and pans, ¡ Pre-Rinse
non-fragile tableware and ¡ Cleaning 70 °C
cutlery.
¡ Intermediate rinse
Level of soiling:
¡ Final rinse 50 °C
¡ Removing stubborn burned or dried-on food
¡ Dry
remnants containing
starch and protein.
All “Additional functions”, Page 20
Tableware:
Sensor-controlled:
All
¡ Cleaning mixed table- ¡ Optimised by sensors de- “Additional
ware and cutlery.
pending on the soiling of functions”,
Level of soiling:
the rinsing water.
Page 20
¡ Removing common
household food remnants
lightly dried-on.
Tableware:
Most economical pro-
¡ Cleaning mixed table- gramme:
ware and cutlery.
¡ Pre-Rinse
Level of soiling:
¡ Cleaning 50 °C
¡ Removing common
¡ Intermediate rinse
household food remnants ¡ Final rinse 35 °C
lightly dried-on.
¡ Drying
All “Additional functions”, Page 20
18
Programme:
Use
Programme sequence
Silence 50 Glass 40°
Express 60° Express 45° Machine Care Favourite
Tableware:
Reduced noise:
¡ Cleaning mixed table- ¡ Pre-Rinse
ware and cutlery.
¡ Cleaning 50 °C
Level of soiling:
¡ Intermediate rinse
¡ Removing common
¡ Final rinse 35 °C
household food remnants lightly dried-on.
¡
Dry
Tableware: ¡ Cleaning delicate table-
ware, cutlery, temperature-sensitive plastics, glasses and stemware in the
stemware basket. Level of soiling: ¡ Removing lightly adhering fresh food
remnants.
Particularly gentle: ¡ Pre-Rinse ¡ Cleaning 40 °C ¡ Intermediate rinse ¡ Final rinse 50 °C ¡ Dry
Tableware:
Time-optimised:
¡ Cleaning mixed table- ¡ Cleaning 60 °C
ware and cutlery.
¡ Intermediate rinse
Level of soiling:
¡ Final rinse 50 °C
¡
Removing common household food remnants
¡
Dry
lightly dried-on.
Tableware:
Time-optimised:
¡ Cleaning delicate table- ¡ Cleaning 45 °C
ware, cutlery, temperat- ¡ Intermediate rinse
ure-sensitive plastics and ¡ Final rinse 50 °C
glasses.
Level of soiling:
¡ Removing lightly adher-
ing fresh food remnants.
Use only if appliance is un- Machine Care 70 °C loaded.
–
–
Note: The relatively long running time in the Eco 50 ° programme is due to longer soaking and drying times. This results in optimal consumption values.
Programmesen Additional functions All “Additional functions”, Page 20
ExtraDry IntensiveZone SpeedPerfect+ “Additional functions”, Page 20
All “Additional functions”, Page 20
ExtraDry “Additional functions”, Page 20
None –
19
enAdditional functions
Information for test institutes
Test institutes are provided with information for comparability tests, e.g.
according to EN60436. These are the conditions for conducting the tests,
however they are not the results or consumption values. E-mail enquiries to:
dishwasher@testappliances.com The product number (E-Nr.) and the production
number (FD) are required here. They can be found on the rating plate on the
appliance door.
Favourite
You can save a combination of a programme and an additional function to the
button. You can save the program via the Home Connect app or on the appliance.
The pre-rinse program is saved to this button at the factory. Pre-rinse is
suitable for all types of tableware. The tableware undergoes intermediate
cleaning via cold rinsing. When programmes have been downloaded and on
delivery of the appliance, the name of the programme will be displayed in the
app. The display alternately shows “AP:P” and the remaining running time. Tip:
You can use the Home Connect app to download additional programmes and save
them to the button.1 Save Favourite on the appliance. 1. Press . 2. Press the
right programme button.
“Programmes”, Page 18 3. Press the button for the relevant
additional function. “Additional functions”, Page 20
4. Press for 3 seconds. a The selected programme and the
additional function will flash. a flashes. a The programme and the additional
function are saved. Tip: To reset the programme, either use the Home Connect
app or reset your appliance back to the factory settings. “Overview of basic
settings”, Page 36
Additional functions Additionalfunctions
You can find an overview of the addi- Additionalfunctions tional functions that can be selected here. Different additional functions, which can be found on the control panel of your appliance, are available depending on the appliance configuration.
Additional func- Use tion
SpeedPerfect+
¡ The run time is shortened by 15% to 75% depending on the rinse programme.
¡ The additional function can be activated before the start of the programme
and at any time when the programme is running.
¡ Energy and water consumption are increased.
1 Depending on the appliance specifications 20
Additional func- Use tion
IntensiveZone
¡ Switch on with mixed loads containing tableware with different soiling
levels, e.g. place very soiled pots and pans in the bottom basket and normally
soiled tableware in the upper basket.
¡ The spray pressure in the bottom basket is increased and the maximum
programme temperature held longer. This will increase the run time and energy
consumption.
ExtraDry
¡ For a better drying result the final rinse temperature is increased and the
drying phase extended.
¡ Especially suitable for drying plastic parts.
¡ There is a slight increase in energy consumption and the run time is
extended.
Features Features
You Features can find an overview of the possible features of your appliance
and how to use them here. These features depend on the model of your
appliance.
Featuresen
Top basket
Arrange cups, glasses and small items of tableware in the top basket.
a
Knife shelf 1 You can adjust the height of the top basket to make room for
larger items of tableware. Adjusting top basket with side levers To wash large
items of tableware in the baskets, adjust the shelf position of the top
basket. 1. Pull out the top basket. 2. To prevent the basket from sud-
denly dropping down, hold the side of the basket by the top edge. 3. Press in
the levers on the right and left on the outside of the basket.
1 Depending on the appliance specifications 21
enFeatures 4. Raise or lower the basket evenly to
the right level.
Check that the basket is level on both sides. 5. Release the levers. a The
basket clicks into position. 6. Slide the basket back in.
Bottom basket
Arrange pans and plates in the bottom basket.
Cutlery basket
Arrange cutlery in the cutlery basket, always without sorting it and with the
sharp points downwards.
a
Cutlery basket 1 Large plates up to a diameter of 28.5 cm can be arranged in
the bottom basket as shown.
1 Depending on the appliance specifications 22
3rd basket
Use the 3rd basket to wash large items of cutlery that are lightly soiled as
well as small items of tableware, e.g. small cups, bowls or cooking spoons.
Featuresen
Etagere
Use the cutlery shelf and space underneath for small cups and glasses or for
large items of cutlery, e.g. cooking spoons or serving cutlery.
Moving the side shelf in the 3rd basket You can move the side shelf in the 3rd
basket to wash stemware in the top basket.
1. Move the side shelf to the left. 2. Arrange the stemware in the top
basket.
If you do not need the cutlery shelf, you can fold it up.
Folding prongs
Use the folding prongs to position tableware securely, e.g. plates.
You can fold the prongs down to position pans, bowls and glasses better.1
Folding down prongs1 If you do not need the prongs, fold them down.
1 Depending on the appliance specifications 23
enFeatures 1. Push the lever forwards
down the prongs .
and fold
1
2
Extra Clean Zone
Use the Extra Clean Zone in the top basket to clean soiled tableware
thoroughly, e.g. muesli bowls.
2. To use the prongs again, fold them back up.
a The prongs audibly click into position.
Knife shelf
Use the shelf for knives and long items of cutlery.
Selecting Extra Clean Zone Note: Consumption will increase if you operate your appliance with the Extra Clean Zone switched on. 1. Pull out the top basket. 2. Set the slider to ON or OFF.
3. Push in the top basket. Cleaning Extra Clean Zone Limescale and soiling
from the dishwashing water can block the nozzles. Note: Always operate the
appliance with the Extra Clean Zone fitted. 1. Pull out the top basket.
24
2. Pull the tab on the Extra Clean Zone up and forwards .
Before using for the first timeen 5. Place the Extra Clean Zone in the
top basket and lock in place .
3. Set the slider to ON. 4. Clean under running water.
Basket heights
Set the baskets at the right height.
Level 1 max. ø 2 max. ø
Top basket 18.5 cm 21 cm
Check that the mounts are in the correct position. a The Extra Clean Zone
audibly clicks into position . 6. Push in the top basket.
Bottom basket 27.5 cm/”28.5 cm” Page 22 25 cm
Before using for the Beforeusingforthefirsttime first time
Before using for the first time
Performing the initial configuration
On initial start-up or after a reset to the factory settings, you will need to
make settings. Tip: Connect your appliance to a mobile device. You can
conveniently change all settings via the Home Connect app. “Home Connect quick
start”, Page 38
Requirement: “The appliance has been installed and connected.” Page 12 1. “Add
special salt.” Page 27 2. “Add rinse aid.” Page 28 3. “Switch on the
appliance.”
Page 34 4. “Setting the water softening sys-
tem.” Page 26 5. “Set the amount of rinse aid to be
dispensed.” Page 29 6. “Add detergent” Page 29. 7. Start the Programme with
the
highest cleaning temperature without tableware.
25
enWater softening system
To remove any marks from water or other residues, we recommend you operate the appliance without tableware before using it for the first time. Tip: You can change these settings and other “Basic settings” Page 36 at any time.
Water softening system Watersofteningsystem
Hard water leaves limescale on the Watersofteningsystem tableware as well as
the washing tank and parts of the appliance may become blocked. To ensure good
dishwashing results, you can treat the water with special salt and the water
softening system. To avoid damage to the appliance, water with a hardness
above 9 °E must be softened.
Overview of water hardness settings
You can find an overview of the water hardness values that can be selected
here. You can find out how hard your water is from your local water company or
by using a water hardness tester.
Water hardness °E 0 – 8 9 – 10 11 – 12 13 – 15 16 – 20 21 – 26 27 – 38 39 – 62
Hardness range Soft Soft Medium Medium Medium Hard Hard Hard
mmol/l 0 – 1.1 1.2 – 1.4 1.5 – 1.8 1.9 – 2.1 2.2 – 2.9 3.0 – 3.7 3.8 – 5.4 5.5 – 8.9
Setting value H:00 H:01 H:02 H:03 H:04 H:05 H:06 H:07
Note: Set the water hardness determined on your appliance. “Setting the water softening system”, Page 26 With a water hardness of 0 – 8 °E you can dispense with special salt for dishwashers and switch off the water softening system. “Switching off the water softening system”, Page 27
Setting the water softening system
Set the water hardness on your appliance. 1. Determine the water hardness and
the appropriate setting value. “Overview of water hardness settings”, Page 26
2. Press . 3. To open the basic settings, press
for 3 seconds. a The display shows H:xx. a The display shows .
26
4. Press or repeatedly until the right water hardness has been set. The value
H:04 is set at the factory.
5. To save the settings, press for 3 seconds.
Special salt
You can use special salt to soften water. Adding special salt If the special
salt refill indicator lights up, add special salt to the dispenser for special
salt just before the programme starts. The consumption of special salt depends
on the water hardness. The higher the water hardness, the greater the
consumption of special salt.
ATTENTION! ¡ Detergent may damage the water
softening system. Only fill the dispenser of the wa-
ter softening system with special dishwasher salt. ¡ Special salt for
dishwashers can damage the tub due to corrosion. To make sure that any special
salt that escapes is washed out of the tub, add the special salt to the
dispenser for special salt immediately before the programme starts.
1. Unscrew the lid of the dispenser for special salt and remove.
2. On initial start-up: Fill the dispenser right up with water.
Water softening systemen 3. Note: Only use special salt for
dishwashers. Do not use salt tablets. Do not use table salt. Add the special
salt to the dispenser.
Fill the dispenser right up with special salt. The water in the dispenser is
displaced and forced out. 4. Place the lid back on the dispenser and turn to
close.
Switching off the water softening system
If you find the special salt refill indicator irritating, e.g. when using
combined detergents with salt replacement substances, you can switch the
indicator off. Note To avoid damage to the appliance, only switch off the
water softening system in the following cases: ¡ The water hardness is max. 26
°E
and you are using combined detergents with salt replacement substances.
According to manufacturers, combined detergents with salt replacement
substances can generally only be used up to a water hardness of 26 °E without
adding special salt.
27
enRinse aid system
¡ The water hardness is 0 – 8 °E. You do not need to use special salt.
1. Press . 2. To open the basic settings, press
for 3 seconds. a The display shows H:xx. a The display shows . 3. Press or
repeatedly until the
display shows H:00. 4. To save the settings, press
for 3 seconds. a The water softening system is
switched off and the salt refill indicator is deactivated.
Regeneration of the water softening system
In order to obtain fault-free function of the water softening system, the appliance performs regeneration of the water softening system at regular intervals. Regeneration of the water softening system takes place before the end of the main rinse cycle in all programmes. It will increase the run time and consumption values, e.g. water and electricity.
Overview of consumption values with regeneration the water softening system Here you can find an overview of the maximum additional run time and consumption values during regeneration of the water softening system.
Regeneration of the water softening 6 system after x rinse cycles
Additional run time in minutes
7
Additional water consumption in 5 litres
Additional power consumption in 0.05 kWh
The consumption values specified are laboratory measurements determined in
accordance with the currently applicable standard and using the Eco 50°
programme and the factory value of the water hardness is set to 16 – 20°E.
Rinse aid system Rinseaidsystem
Rinse aid system
Rinse aid
For optimum drying results, use rinse aid. Only use rinse aid for domestic
dishwashers. Adding rinse aid If the rinse aid refill indicator lights up, top
up with rinse aid. Only use rinse aid for domestic dishwashers. 1. Press the
catch on the lid of the
dispenser for rinse aid and lift .
2
1
28
2. Add rinse aid up to the max mark.
max
3. If rinse aid spills out, remove it from the tub. Spilled rinse aid can
cause excessive frothing during the wash cycle.
4. Close the lid of the dispenser for rinse aid.
a The lid clicks into position.
Setting the amount of rinse aid
If there are streaks or water marks on tableware, change the amount of rinse aid.
1. Press .
2. To open the basic settings, press for 3 seconds.
a The display shows H:xx. a The display shows .
3. Press
repeatedly until
the display shows the value set at
the factory r:05.
4. Press or repeatedly until the right amount of rinse aid has been set.
A low setting adds less rinse aid during the wash cycle and reduces
streaking on tableware.
A higher setting adds more rinse aid during the wash cycle, reduces water
marks and improves the drying result.
Detergenten
5. To save the settings, press for 3 seconds.
Switching the rinse aid system off
If you find the rinse aid refill indicator irritating, e.g. when using combined detergents with a rinse aid component, you can switch the rinse aid system off.
Tip: The function of rinse aid is limited with combined detergents. You will generally get better results using rinse aid.
1. Press .
2. To open the basic settings, press for 3 seconds.
a The display shows H:xx. a The display shows .
3. Press
repeatedly until
the display shows the value set at
the factory r:05.
4. Press or repeatedly until the display shows r:00.
5. To save the settings, press for 3 seconds.
a The rinse aid system is switched off and the rinse aid refill indicator is deactivated.
Detergent Detergent
Detergent
Suitable detergents
Only use detergents that are suitable for dishwashers. Both separate and
combined detergents are suitable. For optimum washing and drying results, use
separate detergent, adding “Special salt” Page 27 and “Rinse aid” Page 28
separately. Modern, powerful detergents mainly use a low-alkaline formulation
with enzymes. Enzymes break down
29
enDetergent
starch and remove protein. Oxygenbased bleaching agents are generally used to remove coloured marks, e.g. tea or ketchup. Note: Follow the manufacturer’s instructions for each detergent.
Detergent Tabs
Powder detergent Liquid detergent
Description Tabs are suitable for all cleaning functions and do not need to be
measured out. With shorter “Programmes” Page 18 tabs sometimes do not dissolve
entirely and leave residues of detergent. This may impair the cleaning effect.
Powder detergent is recommended for shorter “Programmes” Page 18. The dosage
can be adjusted to the level of soiling. Liquid detergent works faster and is
recommended for shorter “Programmes” Page 18 without PreRinse. Sometimes
liquid detergent may leak out despite the detergent dispenser being closed.
This is not a fault and is non-critical if you remember the following: ¡ Only
choose a pro-
gramme without PreRinse. ¡ Do not select timer programming for starting the
programme.
The dosage can be adjusted to the level of soiling.
Tip: Suitable detergents are available online via our website or from “Customer Service” Page 58.
Separate detergents Separate detergents are products that do not contain
components other than detergent, e.g. powder detergent or liquid detergent.
With powder and liquid detergent the dosage can be individually adjusted to
the level of soiling of the tableware. For better washing and drying results
and to avoid damage to the appliance, please additionally use “Special salt”
Page 27 and “Rinse aid” Page 28.
Combined detergent Besides conventional separate detergents, a number of
products are available with additional functions. These products contain not
only detergent but also rinse aid and salt replacement substances (3in1) and,
depending on the combination (4in1, 5in1, …), additional components such as
glass protection or stainless steel cleaner. According to manufacturers,
combined detergents generally only function up to a water hardness of 26 °E.
With a water hardness above 26 °E you will need to add special salt and rinse
aid. For the best washing and drying results we recommend using special salt
and rinse aid from a water hardness of 17 °E. If you are using combined
detergent, the washing programme is adjusted automatically to ensure the best
possible washing and drying result.
30
Unsuitable detergents
Do not use detergent which could cause damage to the appliance or present a risk to health.
Detergent
Description
Hand washing-up Hand washing-up liquid
liquid
can cause increased froth-
ing and damage the appli-
ance.
Detergent containing chlorine
Chlorine residue on tableware may present a risk to health.
Information on detergents
Follow the instructions on detergents in everyday use. ¡ Detergents marked as
“organic” or
“ecological” (environmentally friendly) generally contain lower levels of
active agents or completely dispense with certain substances. The cleaning
effect may be restricted here. ¡ Set the rinse aid and the water softening
system to the separate detergent or combined detergent in use. ¡ According to
manufacturers, combined detergents with salt replacement substances can only
be used up to a certain water hardness, usually 26 °E, without adding special
salt. For the best washing and drying results we recommend using special salt
from a water hardness of 17 °E. ¡ To prevent sticking, only touch detergents
in a water-soluble pouch with dry hands and only ever place them in a dry
detergent dispenser. ¡ Even if the rinse aid and special salt refill
indicators light up, washing programmes will run properly with combined
detergents.
Detergenten ¡ The function of rinse aid is limited
with combined detergents. You will generally get better results using rinse
aid. ¡ Use tablets with a special drying performance.
Adding detergent
1. To open the detergent dispenser, press the locking latch.
2. Add the detergent to the dry detergent dispenser.
50 ml 25 ml 15 ml
If you are using tablets, one is enough. Insert the tablets in a horizontal
position. If you are using powder or liquid detergent, follow the
manufacturer’s instructions and quantities for dosage in the detergent
dispenser. 20 ml 25 ml detergent is sufficient for normal soiling. If
tableware is only lightly soiled, slightly less than the amount of detergent
specified is usually sufficient.
31
enTableware 3. Close the lid of the detergent dis-
penser.
a The lid clicks into position. a The detergent dispenser will open
automatically at the optimum time during the programme. Powder or liquid
detergent will spread around the washing tank and dissolve there. Tablets will
fall into the tablet collecting tray and dissolve in the right dosage. In
order to ensure that tablets can dissolve evenly, do not place any other
objects in the tablet collecting tray. Tip: If you use powder detergent and
select a program with pre-rinse, you can also add a little detergent to the
interior door of the appliance.
Tableware Tableware
Only Tableware clean tableware that is suitable for dishwashers. Note:
Decorated glassware and parts made of aluminium or silver may fade or
discolour with dishwashing. Delicate types of glass may turn cloudy after a
few washing cycles.
Damage to glass and tableware
Only put glasses and china in the dishwasher if it is marked as dishwasher- safe by the manufacturer. Avoid damage to glass and tableware.
Cause
Recommendation
The following table- Only put tableware in
ware is not dish-
the dishwasher if it is
washer-safe:
marked as dish-
¡ Items of cutlery washer-safe by the
and tableware manufacturer.
made from wood
¡ Decorated glass-
ware, antique and
hand-crafted table-
ware
¡ Plastic parts not
resistant to heat
¡ Tableware made
from copper or tin
¡ Tableware soiled
with ash, wax, lub-
ricating grease or
paint
¡ Very small items of
tableware
The chemical composition of detergent causes damage.
Use a detergent marked by the manufacturer as gentle on tableware.
Highly caustic alkaline If you are using highly
or highly acidic clean- caustic alkaline or
ing solutions, in partic- highly acidic cleaning
ular commercial or in- agents, in particular
dustrial cleaners, are commercial or indus-
not safe to use in the trial cleaning agents,
dishwasher with alu- do not put aluminium
minium.
parts in the dish-
washer interior.
32
Cause
Recommendation
The water temperat- Select a programme
ure of the programme with lower temperat-
is too high.
ures.
After the programme
has ended, take glass-
ware and cutlery out
of the appliance
without delay.
Arrange tableware
Arrange tableware correctly to optimise the dishwashing result and prevent
damage to both the appliance and tableware. Tips ¡ Using the appliance allows
you to
save energy and water compared to washing-up by hand. ¡ See our website for
examples of how to load your appliance efficiently, free of charge. ¡ To save
energy and water, load the machine with the number of place settings specified
(standard load with tableware and cutlery). “Technical specifications”, Page
59 ¡ For better washing and drying results, position items with curves or
recesses at an angle so water can run off.
Tablewareen
To save resources, do not prerinse tableware under running water. 2. Observe
the following when arranging tableware: Put heavily soiled tableware in
the bottom basket, e.g. pans. The more powerful the spray jet, the better the
dishwashing result will be. To prevent damage to tableware, arrange it so it
is stable and cannot tip over. To prevent injury, arrange cutlery with the
points and sharp edges facing down. Position containers with the openings
facing down so no water can collect in them. Do not block the spray arms
make sure that they can turn freely. Do not place small parts in the tablet
collecting tray and do not block it with tableware so as not to obstruct the
lid of the detergent dispenser.
1. Remove large remnants of food from tableware. 33
enBasic operation
Removing tableware
WARNING Risk of injury! Hot tableware can cause burns to the skin. When hot,
tableware is sensitive to shock, may crack and can result in injury. When the
programme has ended,
do not empty the appliance until the tableware has cooled down for a while. 1.
To prevent water dripping on the tableware, unload it starting at the bottom
and working up. 2. Check the washing tank and accessories for soiling and
clean if necessary. “Cleaning and servicing”, Page 40
Basic operation Basicoperation
Basic operation
Switching on the appliance
Press . The Eco 50° programme is set by default. The Eco 50° programme is
especially environmentally friendly and ideal for normally soiled tableware.
It is the most efficient programme for the combination of energy/water
consumption for this type of tableware and evidences conformity with the EU
Ecodesign Directive. If you do not perform any actions on the appliance for 10
minutes, the appliance will automatically switch off.
Setting a programme
To adjust the wash cycle to the soiling level of the tableware, select a
suitable programme. Press the right programme button.
“Programmes”, Page 18 a The programme is set and the pro-
gramme button flashes. a The remaining running time of the
programme appears on the display.
Setting additional functions
You can set additional functions to complete the washing programme selected.
Note: The additional functions which can be used depend on the programme
selected. “Programmes”, Page 18 Press the button for the relevant
additional function. “Additional functions”, Page 20 a The additional function
is set and the additional function button flashes.
Setting timer programming
You can delay the start of the programme by up to 24 hours. 1. Press or . a
“00h:01m” appears on the display. 2. Use or to set the re-
quired start time for the programme. 3. Press . a This activates time
preselection. Tip: To deactivate timer programming, press or repeatedly until
“00h:00m” appears in the display.
34
Starting the programme
Press . a The programme has ended when
the display shows “00h:00m”. Notes ¡ If you want to add more tableware
while the appliance is running, do not use the tablet collecting tray as a
handle for the top basket. You might touch the partially dissolved tablet. ¡
You can only change a programme when running if you cancel it. “Terminate
programme”, Page 35 ¡ The appliance switches off automatically 1 minute after
the end of the programme to save energy. If you open the appliance door
immediately after the programme has ended, the appliance will switch off after
4 seconds.
Activating button lock
The button lock prevents the appliance from being operated accidentally or
incorrectly while running. Press for approx. 3 seconds. a The button lock is
activated and
will be automatically deactivated at the end of the programme. a The display
shows “CL” when the appliance is running. a The button lock remains activated
with a power failure.
Deactivate button lock
Press for approx. 3 seconds.
Interrupting programme
Note: When you open the appliance door once the appliance has heated up, leave
the door slightly ajar for a
Basic operationen
few minutes and then close it. This will help prevent excess pressure building
up in the appliance and stop the appliance door bursting open. 1. Press . a
The programme is saved and the
appliance switches off. 2. Press to resume the pro-
gramme.
Terminate programme
To end a programme early or to switch from a programme that has already started, you will need to cancel it first.
Press 4 seconds.
for approx.
a All displays light up.
a As soon as the displays are off,
the display shows “00h:01m” and
the residual water is pumped out.
a The programme is cancelled and
ends after approx. 1 minute.
Switching off appliance
1. Please note the information on “Safe use” Page 10.
2. Press . Tip: If you press during the wash cycle, the programme currently
running will be interrupted. When you switch the appliance back on, the
programme continues automatically.
35
enBasic settings
Basic settings Basicsettings
You Basicsettings can configure the basic settings for your appliance to meet your needs.
Overview of basic settings
The basic settings depend on the features of your appliance.
Basic setting Water hardness
Display text Selection
H:04 1
H:00 – H:07
Rinse aid dispensing r:05 1
r:00 – r:06
Sensor setting Extra Dry
SE:00 1 d:00 1
SE:00 – SE:02 d:00 – d:01
Hot water
A:00 1
A:00 – A:01
1 Factory setting (may vary according to model)
Description Set the water softening system to your water hardness. “Setting
the water softening system”, Page 26 Level H:00 switches the water softening
system off.
Set the amount of rinse aid to be dispensed. “Setting the amount of rinse
aid”, Page 29 Switch the rinse aid system off with level r:00.
Set the water sensor for identifying soiling. “Sensors”, Page 12
The temperature is increased during the final rinse, which improves the drying
result. This may increase the run time slightly. Note: Not suitable for
delicate items of tableware. Switch Extra Dry on “d:01” or off “d:00”.
Set cold water or hot water connection. Only set the appliance to hot water if
this can be prepared with little energy and a suitable installation is
available, e.g. solar heating system with circulation line. The water
temperature should be at least 40 °C and max. 60 °C. Switch hot water on
“A:01” or off “A:00”.
36
Basic setting Start programme
Display text Selection
SP:01 1
SP:00 – SP:01
Tone volume Button volume Wi-Fi
SL:02 1 bL:02 1 Cn:00
SL:00 -SL:03 bL:00 – bL:03 Cn:00 – Cn:01
Remote Start
rc:01
rc:00 – rc:02
1 Factory setting (may vary according to model)
Basic settingsen
Description Set a default programme for when the appliance is switched on. ¡
With the setting “SP:00”, the last
programme selected is set by default when the appliance is switched on. ¡ With
the setting “SP:01”, the Eco 50° programme is set by default when the
appliance is switched on. Adjustment of tone volume. Level “SL:00” switches
the signal tone off. Set the button volume during operation. Level “bL:00”
switches the button tones off. Switch the wireless network connection on or
off. Level “Cn:00” switches the wireless network connection off. The basic
setting “Wi-Fi” is only available once the appliance is connected to the Home
Connect app. “Home Connect “, Page 38 Activate or deactivate “Remote Start “,
Page 39. The following settings are possible: ¡ With the setting “rc:00”, the
function is permanently deactivated. ¡ With the setting “rc:01”, the function
can be selected via the button. “Activating Remote Start “, Page 39 ¡ With the
setting “rc:02”, the function is permanently activated. This basic setting is
not available until after you have connected the device with the Home Connect
app. “Home Connect “, Page 38
37
enHome Connect
Basic setting Factory setting
Display text rE:
Selection Start with Y:ES Confirm with
1 Factory setting (may vary according to model)
Description Restore changed settings to the factory settings. The settings for initial start-up must be configured.
Changing basic settings
1. Press .
2. To open the basic settings, press for 3 seconds.
a The display shows H:xx. a The display shows .
3. Press
repeatedly until
the display shows the required set-
ting.
4. Press or repeatedly until the display shows the right value.
You can change several settings.
5. To save the settings, press for 3 seconds.
Home Connect HomeConnect
This HomeConnect appliance is network-capable. Connect your appliance to a
mobile device to control its functions via the Home Connect app. The Home
Connect services are not available in every country. The availability of the
Home Connect function depends on the availability of Home Connect services in
your country. You can find information about this at: www.home-connect.com. To
be able to use Home Connect, you must first set up the connection to the WLAN
home network (Wi-Fi1) and to the Home Connect app. ¡ “Connecting the appliance
to
WLAN home network (Wi-Fi)”, Page 39
The Home Connect app guides you through the entire login process. Follow the
instructions in the Home Connect app to configure the settings. Tips ¡ Please
consult the documents sup-
plied by Home Connect. ¡ Please also follow the instructions
in the Home Connect app. Note: Please note the safety precautions in this
instruction manual and make sure that they are also observed when operating
the appliance via the Home Connect app. “Safety”, Page 4
Home Connect quick start
Connect your appliance to a mobile device quickly and easily. Installing app
- Install the Home Connect app on
your mobile device.
2. Start the Home Connect app and set up access for Home Connect. The Home Connect app guides you through the entire login process.
1 Wi-Fi is a registered trademark of the Wi-Fi Alliance. 38
Connecting the appliance to WLAN home network (Wi-Fi) Requirements ¡ The Home
Connect app is installed
on your mobile device. ¡ Wi-Fi is activated on the router. ¡ The appliance
receives signals
from the WLAN home network (WiFi) at its installation location. ¡ The
appliance door is closed. 1. With the help of the Home Connect app scan the QR
code.
2. Follow the instructions in the Home Connect app.
Home Connect settings
Adapt Home Connect to your needs. You can find the Home Connect settings in
the basic settings for your appliance. Which settings the display shows will
depend on whether Home Connect has been set up and whether the appliance is
connected to your home network.
Remote Start
You can use the Home Connect app to start the appliance with your mobile
device. Tip: If you select “rc:02” in the “Basic settings” Page 37 of this
function, the function is permanently activated and you can start your
appliance with a mobile device at any time.
Home Connect en
Activating Remote Start When you have selected “rc:01” in the basic settings
of this function, activate the function on your appliance. Requirements ¡ The
appliance is connected to your
WLAN home network. ¡ The appliance is connected to the
Home Connect app. ¡ “rc:01” is selected in the “Basic
settings ” Page 37 of this function. ¡ A programme is selected. Press . If you
open the appliance door, the function is automatically deactivated. a button
lights up. Tip: To deactivate the function, press .
Remote Diagnostics
Customer Service can use Remote Diagnostics to access your appliance if you
contact them, have your appliance connected to the Home Connect server and if
Remote Diagnostics is available in the country in which you are using the
appliance. Tip: For further information and details about the availability of
Remote Diagnostics in your country, please visit the service/support section
of your local website: www.home-connect.com
Software update
You can use this function to update the software of your appliance, e.g. for
optimisation, troubleshooting or safety-relevant updating. The Home Connect
app informs you about available software updates.
39
enCleaning and servicing
Data protection
Please see the information on data protection. The first time your appliance
is registered on a home network connected to the Internet, your appliance will
transmit the following types of data to the Home Connect server (initial
registration): ¡ Unique appliance identification
(consisting of appliance codes as well as the MAC address of the Wi-Fi
communication module installed). ¡ Security certificate of the Wi-Fi
communication module (to ensure a secure data connection). ¡ The current
software and hardware version of your appliance. ¡ Status of any previous
reset to factory settings. This initial registration prepares the Home Connect
functions for use and is only required when you want to use the Home Connect
functions for the first time. Note: Please note that the Home Connect
functions can only be utilised with the Home Connect app. Information on data
protection can be retrieved in the Home Connect app.
Cleaning and servicing Cleaningandservicing
To keep your appliance working effi- Cleaningandservicing ciently for a long
time, it is important to clean and maintain it carefully.
Cleaning the tub
WARNING Risk of harm to health! Using detergents containing chlorine may
result in harm to health. Never use detergents containing
chlorine. 1. Remove any coarse soiling in the
interior with a damp cloth. 2. Add detergent to the detergent dis-
penser. 3. Select the programme with the
highest temperature. “Programmes”, Page 18 4. “Start the programme without
tableware.” Page 35
Cleaning products
Only use suitable cleaning products to clean your appliance. “Safe use”, Page
10 Tip: You can get our tested and approved Dishwasher Care and Machine
Cleaner for Dishwashers online at https://www.bosch-home.com/ store or from
customer service.
Tips on appliance care
Follow the tips on appliance care to make sure your appliance functions properly at all times.
Action Wipe the door seals, the front of the dishwasher and the con-
Benefit This ensures the parts of the appliance will remain clean and hygienic.
40
Cleaning and servicingen
Action
Benefit
trol panel regularly using a damp cloth and washing-up liquid.
Action
Benefit
If the appliance is not This will prevent ungoing to be used for a pleasant odours. while, leave the door slightly ajar.
Machine Care
Deposits, e.g. from remnants of food and limescale, can cause your appliance
to malfunction. To avoid such faults and reduce odours, we recommend cleaning
your appliance at regular intervals. Machine Care combined with machine care
products and machine cleaners is the right programme for the care of your
appliance.
Tip: You can get our tested and approved Dishwasher Care and Machine Cleaner for Dishwashers online at https://www.bosch-home.com/ store or from customer service. Machine Care is a programme which removes various deposits in one washing cycle. Cleaning takes place in two phases:
Phase 1
2
Removal of Grease and limescale
Food remnants and deposits
Detergent
Placement
Liquid machine care product Appliance interior, e.g. bottle
or machine descaler in
hung in the cutlery basket or
powder form.
powder in the interior.
Machine cleaner
Detergent dispenser
To ensure optimum cleaning performance, the programme doses the detergents
independently of each another during the relevant cleaning phase. Correct
placement of the detergents is necessary here. Run Machine Care without
tableware if the indicator for Machine Care lights up on the control panel or
if advised to do so by the display. The indicator will go out after you have
run Machine Care. If your appliance does not have a reminder function, we
recommend performing Machine Care every 2 months.
Running Machine Care Notes ¡ Run the Machine Care programme
without any tableware in the dishwasher.
¡ Only use machine care products and machine cleaners specially designed for
dishwashers.
¡ Make sure that there are no aluminium parts, e.g. extractor hood grease
filters or aluminium pans, in the interior of the appliance.
¡ If you have not run Machine Care after 3 washing cycles, the indicator for
Machine Care will go out automatically.
¡ For optimum cleaning performance, ensure the correct placement of cleaners.
¡ Follow the safety instructions given on the packagings of the machine care
products and machine cleaners.
¡ Activate the “Extra Clean Zone” Page 24 function.
41
enCleaning and servicing 1. Remove any coarse soiling in the
interior with a damp cloth. 2. Clean the filters. 3. Place the machine care
product in
the appliance interior. Only use machine care products specially designed for
dishwashers. 4. Pour the machine cleaner into the detergent dispenser until it
is filled completely. Do not place any additional machine cleaner in the
appliance interior. 5. Press . 6. Press . a Machine Care is run. a Once the
programme has ended, the indicator for Machine Care goes out.
Filter system
The filter system removes coarse soiling from the dishwashing cycle.
3
2
1
1 Micro filter 2 Fine filter 3 Coarse filter
Cleaning filters Soiling in the dishwashing water may block the filters.
1. After each wash check the filters for residue.
2. Turn the coarse filter anticlockwise and remove the filter system .
Check that no foreign objects fall into the sump.
2
1
3. Pull down the micro filter to remove.
4. Press the locking catches together and lift the coarse filter out . 2 1
42
5. Clean the filter elements under running water. Carefully clean the rim of
dirt between the coarse and the fine filter.
6. Re-assemble the filter system. Make sure that the locking catches on the
coarse filter click into position.
7. Insert the filter system into the appliance and turn the coarse filter
clockwise. Make sure that the arrow markings match up.
Cleaning and servicingen 2. Pull up the lower spray arm to re-
move.
3. Check the outlet nozzles on the spray arms for blockages under running
water and remove any foreign bodies.
4. Insert the lower spray arm. a The spray arm clicks into position. 5.
Insert the upper spray arm and
screw it firmly in place.
Cleaning spray arms
Limescale and soiling in the dishwashing water may block the nozzles and
bearings on the spray arms. Clean the spray arms regularly. 1. Unscrew the
upper spray arm
and pull down to remove .
1
2
43
Troubleshooting
Troubleshooting Troubleshooting
You Troubleshooting can rectify minor faults on your appliance yourself. Read
the troubleshooting information before contacting after-sales service. This
will avoid unnecessary costs.
WARNING Risk of electric shock! Incorrect repairs are dangerous. Repairs to
the appliance should only be carried out by trained specialist
staff. Only use genuine spare parts when repairing the appliance. If the power
cord of this appliance is damaged, it must be replaced with a
special connection cable, which is available from the manufacturer or his
Customer Service.
Error code / Fault display / Signal
Fault
Cause
E:20-60 lights up alternately. Appliance has detected calcified heating element.
E:21-30 will light up altern- Intake opening of Zeolith
ately.
container is covered by
items of tableware.
E:30-00 will light up altern- Water protection system is
ately.
activated.
E:31-00 will light up altern- Water protection system is
ately.
activated.
E:32-00 will light up alternately or indicator for water supply lights up.
Supply hose is kinked.
Water tap is turned off. Water tap is jammed or furred up.
The filters in the water connection of the supply or AquaStop hose are blocked.
Troubleshooting
1. Descale the appliance. 2. Operate the appliance with the wa-
ter softening system.1
Re-arrange the tableware in the appliance so the “Intake opening of the Zeolith container ” Page 14 is no longer obstructed.
1. Turn off the water tap. 2. Call “Customer Service”
Page 58.
1. Turn off the water tap. 2. Call “Customer Service”
Page 58.
Install the supply hose without kinks.
Turn on the water tap.
Turn on the water tap. The flow rate must be at least 10 l/ min when the water supply is open.
1. Switch off the appliance. 2. Pull out the mains plug.
1 Depending on the appliance specifications 44
Fault E:32-00 will light up alternately or indicator for water supply lights up.
Cause
Troubleshootingen
Troubleshooting 3. Turn off the water tap. 4. Unscrew the water connection. 5.
Remove the filter from the supply
hose
E:34-00 will light up alternately. E:61-02 will light up alternately.
E:61-03 will light up alternately. Water is not drained.
Water is continuously running into the appliance. Wastewater pump is blocked. Cover of the wastewater pump is loose Wastewater hose is blocked or kinked. Siphon connection is still sealed. Cover of the wastewater pump is loose.
6. Clean the filter. 7. Re-insert the filter in the supply
hose. 8. Screw the water connection back
on. 9. Check the water connection for
leaks. 10. Restore the power supply. 11. Switch the appliance on.
1. Turn off the water tap. 2. Call “Customer Service”
Page 58.
Clean the wastewater pump. “Clean wastewater pump”, Page 57
Secure the cover of the “Wastewater pump ” Page 57 so it clicks
into position.
1. Reposition the wastewater hose without kinks.
2. Remove residues.
Check the connection to the siphon and open if necessary.
Secure the cover of the “Wastewater pump ” Page 57 so it clicks into position.
45
enTroubleshooting
Fault E:90-01 will light up alternately.
E:92-40 will light up alternately. A different error code appears in the
display window. E:01-00 to E:90-10
Cause Mains voltage is too low.
Filters are soiled or blocked. A technical fault is present.
Troubleshooting This is not a fault on the appliance. 1. Contact an
electrician. 2. Have the mains voltage and elec-
trical installation checked by an electrician.
Clean the filters. “Cleaning filters”, Page 42
1. Press . 2. Unplug the appliance or switch off
the fuse. 3. Wait at least 2 minutes. 4. Insert the mains plug of the appli-
ance in a socket or switch on the fuse. 5. Switch the appliance on. 6. If the
problem occurs again:
Press . Turn off the water tap. Pull out the mains plug. Contact “Customer
Service”
Page 58 and give the error code.
Washing results
Fault Tableware is not dry.
Cause No rinse aid used or dosage set too low.
Programme or programme option has no drying phase, or the drying phase is too
brief.
Troubleshooting 1. Add “Rinse aid” Page 28. 2. Set the amount of rinse aid to
be
dispensed. “Setting the amount of rinse aid”, Page 29
“Select a programme with drying, e.g. intensive, strong or ECO programme.”
Page 18 Some option buttons decrease the drying result, e.g varioSpeed.
46
Fault Tableware is not dry.
Troubleshootingen
Cause
Troubleshooting
Water collects in recesses of Position tableware at an angle
the tableware or cutlery.
where possible.
Plastic tableware is not dry. Cutlery is not dry.
Appliance interior still wet after wash cycle.
The combined detergent used has a poor drying performance.
1. Use rinse aid to improve drying performance.
2. Use a different combined detergent with a better drying performance.
Extra Dry not activated to im- Activate Extra Dry. prove drying performance.
Tableware removed too early or drying process not yet ended.
1. Wait until the programme ends. 2. Only remove tableware 30 minutes
after the programme has ended.
Rinse aid used has a limited Use a name-brand rinse aid.
drying performance.
Eco products may have limited ef-
fectiveness.
Not a fault. As plastic does not store heat so well, it also
No remedial action possible.
does not dry as well.
Cutlery not arranged properly in the cutlery basket or cutlery drawer.
Droplets can form on the cutlery contact points. 1. “Arrange cutlery
individually where
possible.” Page 33 2. Avoid points of contact.
Not a fault. The condensation drying principle causes water droplets in the tub they are indeed desirable here. The moisture in the air condenses on the inside walls, runs off and is pumped out.
No action required.
47
enTroubleshooting
Fault Food remnants are left on tableware in the top basket.
Remnants of food on tableware.
Cause Tableware in the top basket was placed too close together or top basket is overfilled.
Troubleshooting Arrange tableware in the top basket
with sufficient space in between. Position large items of tableware at an
angle, e.g. pans and ovenproof dishes.
Activate the Extra Clean Zone function in the top basket. “Selecting Extra
Clean Zone”, Page 24
Tableware is placed too close together or basket is overfilled.
1. Arrange tableware with sufficient space in between. The spray jets must
reach the surfaces of the tableware.
2. Avoid points of contact.
Spray arm rotation is blocked.
Arrange tableware so that it does not obstruct spray arm rotation.
Spray arm nozzles are blocked. Filters are soiled.
Clean the “Spray arms” Page 43. Clean the filters.
“Cleaning filters”, Page 42
Filters are inserted incorrectly and/or not engaged.
1. Insert the filters properly. “Filter system”, Page 42
2. Engage the filters.
Washing programme selec- Select a more intensive washing
ted too weak.
programme.
“Programmes”, Page 18
Adjust the sensitivity of the sensors. “Sensors”, Page 12
Tableware has been pre- Only remove large remnants of food
cleaned too intensely. The
and do not prerinse tableware.
sensors chose a weaker programme. Stubborn soiling cannot be entirely removed.
Adjust the sensitivity of the sensors. “Sensors”, Page 12
Tall narrow receptacles in Do not position tall narrow recept-
corner areas are not rinsed acles at too great an angle or in
adequately.
corner areas.
Top baskets on right and left are not set to same height.
Set the top baskets on the left and right to the same level.
“Top basket”, Page 21
48
Troubleshootingen
Fault Detergent residue in the appliance
Cause Lid of the detergent dispenser is blocked by items of tableware parts and will not open.
Troubleshooting 1. Arrange tableware in the top basket
tableware so the tab collecting tray is not obstructed by tableware. “Arrange
tableware”, Page 33 Items of tableware are blocking the dispenser lid. 2. Do
not place tableware or fragrance dispensers in the tablet collecting tray.
Water marks on plastic parts.
The lid of the detergent dis- Position the tab in the detergent dispenser is blocked by the tab penser crosswise, not vertically. and will not open.
Tabs are used in the quick Select a more intensive “Pro-
or short programme. Dissolv- gramme” Page 18 or use
ing time of the tab is not at-
“Powder detergent” Page 29.
tained.
Washing effect and dissolving performance are reduced after a prolonged storage time or detergent is very lumpy.
Change your “detergent” Page 29.
Due to laws of physics
Select a more intensive pro-
droplet formation on plastic gramme.
surfaces is unavoidable.
“Programmes”, Page 18
After drying water marks are visible.
Position tableware at an angle. “Arrange tableware”, Page 33
Use rinse aid. “Rinse aid”, Page 28
Set the water softening system higher.
Wipeable or water-soluble coatings are present inside
Detergent substances are deposited there. These coat-
Change your “detergent” Page 29.
the appliance or on the door. ings cannot generally be removed with chemicals.
Clean the appliance mechanically.
White coating is deposited in 1. Set the water softening system cor-
the appliance interior.
rectly.
In most cases you will need to increase the setting.
2. Change your detergent if required.
Special salt dispenser is not Screw the special salt dispenser
screwed tight.
tight.
49
enTroubleshooting
Fault
Cause
Troubleshooting
Stubborn white coatings are Detergent substances are Change your “detergent”
present on tableware, inside deposited there. These coat- Page 29.
the appliance or the door.
ings cannot generally be removed with chemicals.
Clean the appliance mechanically.
The hardness range is set incorrectly or the water hard-
Set the Water softening system to the water hardness or add special
ness is greater than 62 °E
salt.
(8,9 mmol/l).
3in1/organic/eco detergent Set the Water softening system to
is not effective enough.
the water hardness and use separ-
ate detergents (proprietary deter-
gent, special salt, rinse aid).
Too little detergent is being Increase the amount of detergent
used.
used or change “Detergent ”
Page 29.
Washing programme selec- Select a more intensive washing
ted too weak.
programme.
“Programmes”, Page 18
Adjust the sensitivity of the sensors. “Sensors”, Page 12
Tea residue or lipstick marks Washing temperature is too Select a programme with a higher
on tableware.
low.
washing temperature.
“Programmes”, Page 18
Too little detergent is being used or is unsuitable.
Use a suitable “Detergent ” Page 29 and follow the manufacturer’s instructions for the amount to be used.
Tableware has been pre- Only remove large remnants of food
cleaned too intensely. The
and do not prerinse tableware.
sensors chose a weaker programme. Stubborn soiling cannot be entirely removed.
Adjust the sensitivity of the sensors. “Sensors”, Page 12
Coloured coatings (blue, yel- The formation of films is due Clean the appliance.
low, brown) that are difficult or impossible to remove are present inside the appliance or on stainless steel tableware.
to substances contained in vegetables (cabbage, celery, potatoes, noodles, etc.) or tap water (manganese).
You can remove deposits with “Mechanical cleaning” Page 40 or a machine cleaning product. It may not always be possible to completely remove deposits but they
are harmless to health.
The formation of films is due Clean the appliance. to metal components on silver or aluminium tableware.
50
Troubleshootingen
Fault
Cause
Troubleshooting
Coloured coatings (blue, yellow, brown) that are difficult or impossible to remove are present inside the appliance or on stainless steel tableware.
You can remove deposits with “Mechanical cleaning” Page 40 or a machine cleaning product. It may not always be possible to completely remove deposits but they are harmless to health.
Coloured deposits (yellow, The formation of films is due 1. Check the setting of the water
orange, brown) that are easy to ingredients of food rem-
softening system.
to remove are present inside nants and tap water (limes- 2. Add special salt.
the appliance (mainly at the cale) “soaplike”.
“Adding special salt”, Page 27
bottom).
3. If you are using combined deter-
gents (tabs), activate the water
softening system.
Follow the information about detergents. “Information on detergents”, Page 31
Plastic parts inside the appli- Plastic parts inside the appli- Discolouration can come about and
ance are discoloured.
ance may become discol-
will not impair functioning of the ap-
oured during the life of the
pliance.
dishwasher.
Plastic parts are discoloured.
Washing temperature is too Select a programme with a higher
low.
washing temperature.
“Programmes”, Page 18
Tableware has been pre- Only remove large remnants of food
cleaned too intensely. The
and do not prerinse tableware.
sensors chose a weaker programme. Stubborn soiling cannot be entirely removed.
Adjust the sensitivity of the sensors. “Sensors”, Page 12
Removable streaks are present on glasses, glassware with a metallic appearance and cutlery.
Amount of rinse aid to be dispensed is set too high. No rinse aid has been added.
Set the rinse aid system to a lower setting.
“Adding rinse aid”, Page 28
Detergent residue is present 1. Arrange tableware in the top basket
in the final rinse. Lid of the
tableware so the tab collecting tray
detergent dispenser is
is not obstructed by tableware.
blocked by tableware items “Arrange tableware”, Page 33
and will not open fully.
Items of tableware are blocking the
dispenser lid.
2. Do not place tableware or fragrance dispensers in the tablet col-
lecting tray.
51
enTroubleshooting
Fault Removable streaks are present on glasses, glassware with a metallic
appearance and cutlery.
Irreversible clouding of glassware.
Cause
Troubleshooting
Tableware has been pre- Only remove large remnants of food
cleaned too intensely. The
and do not prerinse tableware.
sensors chose a weaker programme. Stubborn soiling cannot be entirely removed.
Adjust the sensitivity of the sensors. “Sensors”, Page 12
Glasses are not dishwasherproof, only suitable for dishwashers.
Use dishwasher-proof glasses. Glasses are usually only suitable for use in a dishwasher, i.e. long-term wear or long-term changes must be expected.
Avoid a lengthy steam phase (standing time after wash cycle ends).
Use a programme with a lower temperature. “Programmes”, Page 18
Set the softening system to the water hardness.
Use detergent with a glass protection component.
Rust spots on cutlery.
Cutlery is not sufficiently rust-resistant. Knife blades are often more severely affected.
Use rust-resistant tableware.
Cutlery may also rust if washed together with rusting items. Salt content in washing water is too high.
Do not wash rusting items. 1. Remove any spilled special salt
from the tub. 2. Screw the cap of the special salt
dispenser on tight.
Detergent residue is present Spray arms were blocked by Check that the spray arms are not in the detergent dispenser tableware so detergent was blocked and can rotate freely. or the tablet collecting tray. not rinsed out.
Detergent dispenser was damp when detergent was added.
Only add detergent to a detergent dispenser when dry.
Excessive formation of foam Hand washing-up liquid is
occurs.
present in dispenser for
rinse aid.
Immediately add rinse aid to the dispenser. “Adding rinse aid”, Page 28
Rinse aid has been spilled. Remove the rinse aid with a cloth.
52
Troubleshootingen
Fault Excessive formation of foam occurs.
Cause
Troubleshooting
Detergent or appliance care Change the brand of detergent. product used causes excessive foaming.
Home Connect problem
Fault Connection to home network is not established. WLAN display is flashing.
Home Connect cannot be implemented correctly.
Cause WLAN on router is not active. Connection to home network is not available. Home Connect set incorrectly. Technical fault is present.
Troubleshooting Check the wireless network con-
nection of your router. Activate the wireless network con-
nection on your router. Please consult the documents sup-
plied for Home Connect. Please consult the information
about support in the documents supplied for Home Connect.
Information on display panel
Fault Special salt refill indicator lights up. Refill indicator for special
salt does not light up. Refill indicator for rinse aid lights up.
Refill indicator for rinse aid does not light up.
Cause
Troubleshooting
Insufficient special salt.
Add “Special salt” Page 27.
Sensor does not detect spe- Do not use special salt tablets. cial salt tablets.
Water softening system is Setting the water softening system switched off.
Insufficient rinse aid.
1. Add “Rinse aid” Page 28. 2. Set the amount of rinse aid to be
dispensed. “Setting the amount of rinse aid”, Page 29
Rinse aid system is switched Set the amount of rinse aid to be
off.
dispensed.
Malfunctions
Fault
Cause
Water is left in the appliance Filter system or area under
at the end of the pro-
the filters is blocked.
gramme.
Programme has not yet ended.
Troubleshooting
1. Clean the “Filters” Page 42. 2. Clean the “Wastewater pump”
Page 57.
Wait until the programme ends or cancel the programme with Reset.
53
enTroubleshooting
Fault
Cause
Water is left in the appliance at the end of the programme.
Appliance cannot be switched on or operated.
Software update is taking place.
Troubleshooting “Terminate programme”,
Page 35
Wait until the software update has finished.
Appliance functions have failed.
1. Pull out the mains plug or switch off the fuse.
2. Wait at least 2 minutes. 3. Connect the appliance to the power
supply. 4. Switch the appliance on.
Appliance does not start.
The mains fuse has tripped. Mains cable is not inserted.
Check the relevant fuse. 1. Check whether the socket works. 2. Check whether
the mains cable is
properly inserted in the socket and on the rear of the appliance.
Appliance door is not closed Close the appliance door. properly.
Programme starts automat- You did not wait until pro-
ically.
gramme ended.
“Terminate programme”, Page 35
Appliance stops during the programme or cuts out.
Appliance door is not closed Close the appliance door. properly.
Power and/or water supply 1. Check the power supply.
has been interrupted.
2. Check the water supply.
Top basket is pressing against inner door and preventing appliance door from being closed securely.
Check whether the rear panel of the appliance is being pressed in by a socket or hose holder that has not been removed.
Arrange the tableware so that no parts project beyond the basket and prevent the appliance door from closing properly.
54
Troubleshootingen
Fault All LEDs lit up or flashing.
Cause Electronics have detected a fault.
Troubleshooting 1. Press the main switch button for ap-
prox. 4 seconds. “Controls”, Page 15 The appliance is reset and restarted. 2.
If the problem occurs again:
Switch off the appliance. Pull out the mains plug or
switch off the fuse in the fuse box. Wait at least 2 minutes. Switch on the
fuse in the fuse box or insert the mains plug. Switch the appliance on. 3. If
the problem occurs again: Contact customer service. “Customer Service”, Page
58
Mechanical damage
Fault Appliance door cannot be closed.
Lid on the detergent dispenser cannot be closed.
Cause Door lock has been activated. Door cannot be closed due to installation
method.
Detergent dispenser or lid are blocked by sticky detergent residue.
Troubleshooting Close the appliance door with
greater force.
Check whether the appliance has been installed properly. When closed, the
appliance door, its decor or attached parts should not knock against adjacent
cabinets or the worktop.
Remove detergent residue.
Noise
Fault Filling valves making knocking noises.
Knocking or rattling noise.
Cause Caused by the domestic installation. No appliance fault present. Does not affect functioning of the appliance. Spray arm is striking tableware.
Troubleshooting Can only be remedied in the do-
mestic installation.
Arrange tableware so that the spray arms do not strike tableware.
55
enTroubleshooting
Fault Knocking or rattling noise.
Cause
Troubleshooting
With a small load the water jets directly strike against the tub.
Distribute the tableware evenly. Load the appliance with more table-
ware.
Light items of tableware Position light items of tableware semove about during the wash curely. cycle.
56
Clean wastewater pump
Large remnants of food or foreign bodies can block the waste water pump. As
soon as the rinsing water no longer drains properly, the waste water pump must
be cleaned.
WARNING Risk of injury! Sharp and pointed objects or fragments of glass may
block the waste water pump and cause injury. Remove any foreign bodies care-
fully. 1. Disconnect the appliance from the
power supply. 2. Remove the top and bottom bas-
ket. 3. Remove the filter system. 4. Scoop out any water.
Use a sponge if necessary. 5. Prise off the pump cover using a
spoon and grip it by the crosspiece.
6. Lift the pump cover inwards at an angle and remove.
a You can now reach the impeller with your hand.
7. Remove any remnants of food and foreign bodies in the area of the
impeller.
Transportation, storage and disposalen 8. Insert the pump cover and press
down .
2 1
a The pump cover clicks into position.
9. Install the filter system. 10.Insert the top and bottom basket.
Transportation, storage Transportation,storageanddisposal and disposal
Transportation, storage and disposal
Removing the appliance
1. Disconnect the appliance from the mains power supply.
2. Turn off the water tap. 3. Detach the drainage connection. 4. Detach the
drinking water connec-
tion. 5. Loosen any screws fastening the
appliance to cabinet parts. 6. Remove the base panel if fitted. 7. Pull the
appliance out carefully,
along with the hose behind it.
Protect appliance from frost
If there is a risk of frost where the appliance will be standing, e.g. in a
holiday home, empty the appliance completely. Empty the appliance.
“Transporting the appliance”, Page 58
57
enCustomer Service
Transporting the appliance
To avoid damage to the appliance, empty it before transporting. Note: Always
transport the dishwasher upright to prevent residual water getting into the
machine’s controls and damaging the appliance. 1. Remove tableware from the
appli-
ance. 2. Secure loose parts. 3. “Switch on the appliance.”
Page 34 4. Select the programme with the
highest temperature. “Programmes”, Page 18 5. “Start the programme.” Page 35
6. To drain the appliance, terminate the programme after approx. 4 minutes.
“Terminate programme”, Page 35 7. “Switch off the appliance.” Page 35 8. Turn
off the water tap. 9. To empty the residual water out of the appliance, detach
the supply hose and let the water drain out.
Disposing of old appliance
Valuable raw materials can be reused by recycling.
WARNING Risk of harm to health! Children can lock themselves in the appliance,
thereby putting their lives at risk. With redundant appliances, unplug
the power cord. Then cut through the cord and damage the lock on the appliance
door beyond repair so that the appliance door will no longer close.
1. Unplug the appliance from the mains.
2. Cut through the power cord. 3. Dispose of the appliance in an en-
vironmentally friendly manner. Information about current disposal methods are
available from your specialist dealer or local authority.
This appliance is labelled in accordance with European Directive 2012/19/EU
concerning used electrical and electronic appliances (waste electrical and
electronic equipment – WEEE). The guideline determines the framework for the
return and recycling of used appliances as applicable throughout the EU.
Customer Service CustomerService
Function-relevant CustomerService genuine spare parts according to the
corresponding Ecodesign Order can be obtained from Customer Service for a
period of at least 10 years from the date on which your appliance was placed
on the market within the European Economic Area. Note: Under the terms of the
manufacturer’s warranty the use of Customer Service is free of charge.
Detailed information on the warranty period and terms of warranty in your
country is available from our aftersales service, your retailer or on our
website. If you contact Customer Service, you will require the product number
(ENr.), the production number (FD) and the consecutive numbering (Z-Nr.) of
your appliance.
58
The contact details for Customer Service can be found in the enclosed Customer
Service directory or on our website.
Product number (E-Nr.), production number (FD) and consecutive numbering
(Z-Nr.)
You can find the product number (ENr.), the production number (FD) and the
consecutive numbering (Z-Nr.) on the appliance’s rating plate. The rating
plate is located inside the appliance door. Make a note of your appliance’s
details and the Customer Service telephone number to find them again quickly.
AQUA-STOP guarantee
In addition to warranty claims against the seller under the purchase agreement
and in addition to our manufacturer’s warranty, we offer compensation under
the following conditions. ¡ If our Aqua-Stop system is defect-
ive and causes water damage, we will make good the damage for private users.
To ensure protection from water damage, the appliance must be connected to the
power supply. ¡ The liability guarantee is valid for the service life of the
appliance. ¡ A claim can only be made under the guarantee if the appliance has
been correctly installed and connected with Aqua-Stop according to our
instructions; this also includes correctly fitting the AquaStop extension
(genuine accessory). Our guarantee does not cover
Technical specificationsen defective supply lines or fittings up to the Aqua- Stop connection on the tap. ¡ If your appliance is fitted with Aqua-Stop, you can in principle leave your appliance unattended during operation and the tap turned on afterwards. The tap only needs to be turned off if you are away from home for a long period, e.g. on holiday for several weeks.
Technical specifications Technicalspecifications
Technical specifications
Weight Voltage
Power rating Fuse Water pressure
Inlet rate Water temperature
Capacity
Max.: 60 kg 220 – 240 V, 50 Hz or 60 Hz 2000 – 2400 W 10 – 16A ¡ min. 50 kPa
(0.5 bar) ¡ max. 1000 kPa
(10 bar) Min. 10 l/min Cold water. Hot water max.: 60 °C 13 place settings
You can find more information about your model online at https://eprel.ec.europa.eu/1. This web address is linked to the official EU EPREL product database. Please then follow the instructions on searching for the model. The model identifier is made up of the characters before the slash in the product number (E-Nr.) on the rating plate. Alternatively, you can also find the model identifier in the first line of the EU energy label.
1 Only applies to countries in the European Economic Area 59
Declaration of Conformity
Information regarding Free and Open Source Software
This product includes software components that are licensed by the copyright
holders as free or open source software. The applicable licence information is
stored on your home appliance. You can also access the applicable licence
information via your Home Connect app: “Profile -> Legal information ->
Licence Information”.1 You can download the licence information on the brand
product website. (Please search on the product website for your appliance
model and additional documents). Alternatively, you can request the relevant
information from ossrequest@bshg.com or BSH Hausgeräte GmbH, Carl-Wery-Str.
34, 81739 Munich, Germany. The source code will be made available to you on
request. Please send your request to ossrequest@bshg.com or BSH Hausgeräte
GmbH, Carl-Wery-Str.34, 81739 Munich, Germany. Subject: ,,OSSREQUEST” The cost
of performing your request will be charged to you. This offer is valid for
three years from the date of purchase or at least as long as we offer support
and spare parts for the relevant appliance.
Declaration of Conformity DeclarationofConformity
BSH Hausgeräte GmbH hereby de- DeclarationofConformity clares that the
appliance with Home Connect functionality conforms to the basic requirements
and other relevant provisions of Directive 2014/53/ EU. A detailed RED
Declaration of Conformity can be found online at www.bosch-home.com among the
additional documents on the product page for your appliance.
Hereby, BSH Hausgeräte GmbH declares that the appliance with Home Connect
functionality is in compliance with relevant statutory requirements.2 A
detailed Declaration of Conformity can be found online at www.boschhome.co.uk
among the additional documents on the product page for your appliance.2
Only applies to Great Britain 2.4 GHz band (24002483.5 MHz): Max. 100 mW 5
GHz band (51505350 MHz + 54705725 MHz): Max. 100 mW
BE
BG
CZ
DK
DE
EE
FR
HR
IT
CY
LI
LV
MT NL
AT
PL
PT
RO
SE
NO
CH
TR
IS
UK (NI)
5 GHz WLAN (Wi-Fi): For indoor use only.
IE
EL
ES
LT
LU
HU
SI
SK
FI
1 Depending on the appliance specifications 2 Only applies to Great Britain 60
Declaration of Conformityen
AL
BA
MD
ME
MK
RS
UK
UA
5 GHz WLAN (Wi-Fi): For indoor use only.
61
Thank you for buying a Bosch Home Appliance!
Register your new device on MyBosch now and profit directly from:
· Expert tips & tricks for your appliance · Warranty extension options ·
Discounts for accessories & spare-parts · Digital manual and all appliance
data at hand · Easy access to Bosch Home Appliances Service
Free and easy registration also on mobile phones: www.bosch-home.com/welcome
Looking for help? You’ll find it here.
Expert advice for your Bosch home appliances, help with problems or a repair from Bosch experts. Find out everything about the many ways Bosch can support you: www.bosch-home.com/service Contact data of all countries are listed in the attached service directory.
BSH Hausgeräte GmbH Carl-Wery-Straße 34 81739 München, GERMANY www.bosch-
home.com
A Bosch Company
9001468538
9001468538 (020414) 650 A1 en
Valid within Great Britain: Imported to Great Britain by BSH Home Appliances Ltd. Grand Union House Old Wolverton Road Wolverton, Milton Keynes MK12 5PT United Kingdom
References
- Appliances.com
- Home Appliances Global Website | Bosch
- Home.co.uk: Property Search, Homes For Sale, Estate Agents, Sell Your House
- Nect | Home
- Home Appliances Global Website | Bosch
- Welcome to MyBosch
- Connect your household | Home Connect
- Home Appliances Global Website | Bosch
- Find your Bosch Online Shop | BOSCH
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>