MARVEL MLCR215-IS01A Undercounter Refrigeration Owner’s Manual
- June 11, 2024
- Marvel
Table of Contents
MARVEL MLCR215-IS01A Undercounter Refrigeration
Welcome to the Marvel Experience!
Thank you for choosing our quality American-built product to add to your home.
We are thrilled to welcome you to our growing community of Marvel owners, who
trust in our products and our support.
The information in this guide is intended to help you install and maintain your new Marvel undercounter model to pro-tect and prolong its lifetime. We encourage you to contact our Technical Support team at 616-754-5601 with any questions.
Got a Marvelous Design?
We would love to see how your Marvel product looks in its new home. Send us
photos at marketing@marvelre-frigeration.com, and we might feature your Marvel home design on our website
and social media!
Warranty Registration
It is important you send in your warranty registration card immediately after taking delivery of your appliance or you can register online at www.marvelrefrigeration.com
The following information will be required when registering your appliance:
Service Number
Serial Number
Date of Purchase
Dealer’s name and address
Online registration available at www.marvelrefrigeration.com
The service number and serial number can be found on the serial plate which is located inside the cabinet on the left side near the top.
Tip: Click on any section below to jump directly there
Installation
- Integrated Panel Dimensions
- Integrated Panel Installation
Installation Operation and Maintenance Instructions
Overlay Door Panel Dimensions – ML 1scRP1xP
OVERLAY PANEL NOTICE
Due to differences in surrounding cabinetry the panel may not perfectly align
with door. The procedure below is designed to provide a finished overlay panel
that seamlessly integrates with surrounding cabinetry.
The door panel must not weigh more than 20 lbs (10 kg).
It is important to ensure that all drilled holes are drilled to the correct
depth in order to avoid splits in the wood when hardware is installed.
When applying an overlay panel to a unit, ensure that both sides are finished
in order to prevent warping.
A full overlay door panel completely covers the door frame and provides a
built-in appearance.
Overlay Panel Preparation
- Cut the panels to the dimensions listed in the diagram below.
- Optional: Stain or Finish panel to desired stain or color. Be sure to closely follow the instructions provided by the manufacturer.
- Optional: Install handles and hardware.
Overlay Panel Dimensions
INTEGRATED PANEL INSTALLATION
- 5/8″ (1.6 cm) or 3/4″ (1.9 cm) panel
- 14 5/8 (37.1 cm) width
- 29 21/32″ (75.3 cm) height
-
Fully open door.
-
Starting at corner, pull gasket away from door.
-
Continue to pull gasket free from gasket channel.
-
Upon removal, lay gasket down on a flat surface.
-
Align top of panel with top edge of door. Center panel on door.
NOTE Due to differences in floor construction or surrounding cabinetry, the panel may not sit flush with the top of the door. -
Secure integrated panel to door using clamps. A robust tape may also be used. Marvel recommends the use bar clamps to secure the panel to the door. If using tape, be certain the tape will not damage panel finish upon removal.
-
Using a 7/64″ (3 mm) drill bit, drill 6 pilot holes into the wood panel 1/2″ (12 mm) deep using the holes in the door frame as a guide.
NOTE It is important to ensure that all drilled holes are drilled to the correct depth in order to avoid splits in the wood when hardwood is installed. -
Locate 6 of the #6x 1-1/2″ (38 mm) screws provided with your unit.
-
Using a Phillips screwdriver, place one screw into each of the 6 pilot holes and screw down. Do not overtighten screws.
-
Ensure the screws sit flush against the bottom of the channel.
-
Remove clamps from door.
NOTE If panel requires additional adjustment after removing clamps, slightly loosen each screw and adjust panel as necessary. Tighten screws upon completion. -
Starting at the corners, re-install the gasket into the gasket channel in the frame. Make sure the gasket is fully seated.