dji MINI 3 Pro Camera Drones User Guide

dji MINI 3 Pro Camera Drones

Safety at a Glance

By using this product, you signity that you have read, understand, and accept the terms and conditions here. EXCEPT AS EXPRESSLY PROVIDED IN AFTER-SALES SERVICE POLICIES AVAILABLE AT (http://www.dji.com/service), THE PRODUCT AND ALL MATERIALS AND CONTENT AVAILABLE THROUGH THE PRODUCT ARE PROVIDED “AS IS” AND ON “AS AVAILABLE BASIS” WITHOUT WARRANTY OR CONDITION OF ANY KIND. This product is not intended for children.

Flight Environment

WARNING

• DO NOT use the aircraft in severe weather conditions including heavy wind exceeding 10.7 m/s, snow, rain, fog, hail, or lightning.
• Fly the aircraft below 4,000 m (13,123 ft.) above sea level.
• DO NOT fly the aircraft in environments where the temperature is below -10° C (14° F) or above 40° C (104° F).
• DO NOT take off from moving objects such as cars, ships, and airplanes.
• DO NOT fly close to reflective surfaces such as water or snow. Otherwise, the vision system may be limited.
• When the GNSS signal is weak, fly the aircraft in environments with good lighting and visibility. Low ambient light may cause the vision system to work abnormally.
• DO NOT fly the aircraft near areas with magnetic or radio interference, including Wi-Fi hotspots, routers, Bluetooth devices, high-voltage lines, large scale power transmission stations, radar stations, mobile base stations, and broadcasting towers.

NOTICE

• Be careful when taking off in the desert or from a beach to avoid sand entering the aircraft.
• Fly the aircraft in open areas. Buildings, mountains, and trees may block the GNSS signal and affect the on-board compass.

Flight Operation’

WARNING

• Stay away from rotating propellers and motors.
• Make sure the aircraft batteries, remote controller, and the mobile device are fully charged.
• Be familiar with the selected flight mode and understand all safety functions and warnings.

NOTICE

• Make sure DJITM Fly and aircraft firmware have been updated to the latest version.
• Land the aircraft in a safe location when there is a low battery or high wind warning. Use the remote controller to control the speed and altitude of the aircraft to avoid collisions during Return-to-Home.

Battery Safety Notice

• DO NOT allow liquid to come into contact with the batteries.
• DO NOT leave batteries covered in moisture or out in the rain.
• DO NOT drop the batteries into water. Otherwise, an explosion or fire may occur.
• DO NOT use non-DJI batteries. It is recommended to use DJI chargers.
• DO NOT use swollen, leaking, or damaged batteries. In such situations, contact DJI or a DJI authorized dealer.
• The batteries should be used at a temperature between -10° to 40° C (14° to 104° F). High temperatures can cause an explosion or fire. Low temperatures will reduce the performance of a battery.
• DO NOT disassemble or pierce the battery in any way.
• The electrolytes in the battery are highly corrosive. If any electrolytes come into contact with your skin or eyes, immediately wash the affected area with water and seek medical support.
• Keep the batteries out of the reach of children and animals.
• DO NOT use a battery if it is involved in a crash or heavy impact.
• Extinguish any battery fire using water, sand, or a dry powder fire extinguisher.
• DO NOT charge the battery immediately after flight. The battery temperature may be too high and may cause serious damage to the battery. Allow the battery to cool down to close to room temperature before charging. Charge the battery at a temperature range of 5° to 40° C (41° to 104° F). The ideal charging temperature range is 22° to 28° C (72° to 82° F). Charging at the ideal temperature range can prolong battery life.
• DO NOT leave the batteries near heat sources such as a furnace or heater or inside a vehicle on a hot day.
• DO NOT store the battery for an extended period after fully discharging. Otherwise, the battery may over-discharge and cause irreparable damage to the battery cell.
• If a battery with a low power level has been stored for an extended period, the battery will enter deep hibernation mode. Recharge the battery to bring it out of hibernation.

Specifications

Compliance Information

FCC Compliance Notice
Supplier’s Declaration of Conformity
Product name: DJI Mini 3 Pro
Model Number: MT3M3VD; RM330
Responsible Party: DJI Technology, Inc.
Responsible Party Address: 201 S. Victory Blvd., Burbank, CA 91502
Website: www.dji.com

We, DJI Technology, Inc., being the responsible party, declares that the above mentioned model was tested to demonstrate complying with all applicable FCC rules and regulations.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

RF Exposure Information
The aircraft complies with FCC radiation exposure limits set forth for an uncontrolled environment. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna shall not be less than 20cm during normal operation. This transmitter must not be co- located or operating in conjunction with any other antenna or transmitter.

This remote controller complies with FCC radiation exposure limits set forth for an uncontrolled environment. End user must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

The portable device is designed to meet the requirements for exposure to radio waves established by the Federal Communications Commission (USA). These requirements set a SAR limit of 1.6 W/kg averaged over one gram of tissue. The highest SAR value reported under this standard during product certification for use when properly worn on the body.

ISED Compliance Notice
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1)This device may not cause interference.(2)This device must accept any interference, including interference that may cause undesired operation of the device.

This equipment complies with RSS‐102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. End user must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The portable device is designed to meet the requirements for exposure to radio waves established by the ISED.

The device for operation in the band 5150–5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems.

These requirements set a SAR limit of 1.6 W/kg averaged over one gram of tissue. The highest SAR value reported under this standard during product certification for use when properly worn on the body.

EU Compliance Statement:
SZ DJI TECHNOLOGY CO., LTD. hereby declares that this device (DJI Mini 3 Pro) is in compliance with the essential requirements and other relevant provisions of the Directive 2014/53/EU.

A copy of the EU Declaration of Conformity is available online at www.dji.com /euro-compliance EU contact address: DJI GmbH, Industries trasse 12, 97618, Niederlauer, Germany

Compliance Statement:
SZ DJI TECHNOLOGY CO., LTD. hereby declares that this device (DJI Mini 3 Pro) is in compliance with the essential requirements and other relevant provisions of Radio Equipment Regulations 2017.
A copy of the GB Declaration of Conformity is available online at www.dji.com /euro-compliance

Environmentally friendly disposal
Old electrical appliances must not be disposed of together with the residual waste, but have to be disposed of separately. The disposal at the communal collecting point via private persons is for free. The owner of old appliances is responsible to bring the appliances to these collecting points or to similar collection points. With this little personal effort, you contribute to recycle valuable raw materials and the treatment of toxic substances.

https://www.dji.com/mini-3-pro/downloads

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>