ARRIS X6 11ax Tri-band Extender User Guide
- June 11, 2024
- Arris
Table of Contents
x6042
Mesh Extender
Quick Start Guide
IMPORTANT SAFETY INSTRUCTIONS
The model number, serial number, and electrical rating are on a label on the
base of the device. Do not locate the device near water. Do not locate the
device in direct sunlight or near a heat source. Do not use liquids,
aerosols, or forced air to clean the device. It may be cleaned using a dry,
lint-free cloth. Do not block the ventilation holes on this device. Do not
stand it on soft furnishings or carpets. Do no use the device in an
environment that exceeds 104º F (40º C). Use only the power supply and cord
provided with the device. Do not use the power supply with any other devices.
Open source software and licenses
For instructions on how to obtain a copy of any source code being made
publicly available by ARRIS related to software used in this ARRIS product you
may send your request in writing to: RRIS, Software Pedigree Operations, 2450
Walsh Avenue, Santa Clara, CA 95051, USA. The ARRIS website
opensource.arris.com also contains information
regarding use of open source.
ARRIS has created opensource.arrisi.com to serve as a portal for interaction
with the software community-at-large.
FCC Compliance
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
What’s in the box
How to read your Mesh Extender LEDs
| State | LED Color | |
|---|---|---|
| Power | Starting up | fast blinking green |
| Up; not connected to network | slow blinking green | |
| Wired | Fast network speed | solid green |
| Limited network speed | solid yellow | |
| Slow network speed | solid red | |
| WPS | WPS process ongoing | blinking yellow |
| WPS pairing unsuccessful | fast blinking red; 10 seconds | |
| WPS pairing successful | fast blinking green; 10 seconds | |
| Wireless | Extender at good position | solid green |
| Extender far from router/ gateway | solid yellow | |
| Extender too far from router/gateway | solid red |
Connect your X6042 Wired Connection
Has your service provider informed you that your ARRIS gateway is HomeAssure Enabled? NO
-
Connect your first X6042 Mesh Point to your current gateway using an Ethernet cable. Then connect the Mesh Point to power and switch to ON.
The LED will blink fast, then blink slow, then turn to solid green. This will take a couple of minutes. Now, you are ready to add additional Mesh Points to the network.
-
Locate your second Mesh Point approximately 5-15m from your gateway; if you have line-of-sight they can be further apart, but move closer if there are thick walls between.
-
Pair the units: Push the WPS button on the first Mesh Point, then push the WPS button on the second Mesh Point. Note: When adding additional Mesh Points, always push the button on the first.
Mesh Point
and then push the WPS button on the Mesh Point you are adding. -
The LED on the second Mesh Point flashes green quickly when the two units pair successfully.
-
The second Mesh Point will be automatically configured with the same Wi-Fi settings as the first Mesh Point; this will take a few moments.
-
When configuration is complete, the LED on the second Mesh Point will change color to indicate the quality of the link between the first and the second Mesh Points. See How to read your Mesh Extender LEDs in this guide to understand the state the LED color indicates.
Connect your X6042 with HomeAssure™ enabled
Has your service provider informed you that your ARRIS gateway is HomeAssure Enabled? YES
-
Locate your first X6042 Mesh Point approximately 5-15m from your gateway; if you have line-of-sight they can be further apart, but move closer if there are thick walls between. Connect the Mesh Point to power and switch to ON.
-
Pair the gateway and the Mesh Point: Push the WPS button on the gateway, then push the WPS button on the Mesh Point. The LED on the Mesh Point flashes green quickly when it has paired successfully with the gateway.
-
Next, the LED will change color to indicate the quality of the link between the gateway and the Mesh Point. See How to read your Wireless Extender LEDs in this guide to understand the state the LED color indicates.
-
To add additional Mesh Points, repeat steps 1-3. Additional Mesh Points are configured with the same Wi-Fi settings as the first Mesh Point.
Connecting clients (optional) You can connect to your network in two ways:
-
Use the Wi-Fi credentials used for your HomeAssure enabled-gateway or the Wi-Fi credentials printed on the first Mesh Point connected to your gateway.
-
Use the WPS button on the front of the Mesh Point and the WPS Push-button configuration (PBC) functionality on your device.
Canadian Compliance
CAN ICES-03(B)/NMB-3(B)
This device complies with ISED’s license-exempt RSSs. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
The device meets the exemption from the routine evaluation limits in section
2.5 of RSS 102 and compliance with RSS-102 RF exposure, users can obtain
Canadian information on RF exposure and compliance.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
This equipment complies with ISED radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
greater than 22 cm between the radiator & your body.
Caring for the Environment by Recycling
When you see this symbol on an ARRIS product, do not dispose of the product
with residential or commercial waste.
Please recycle product packaging and this document.
Recycling your ARRIS equipment
Some countries or regions have set up systems to collect and recycle
electrical and electronic waste items.
Recycling information can be obtained from the WEEE recycling section at
www.CommScope.com.
© 2023 CommScope, Inc. All rights reserved. All trademarks identified by ™ or ® are trademarks or registered trademarks in the US and may be registered in other countries. All product names, trademarks, and registered trademarks are property of their respective owners.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>