FOXWELL NT201 Scanner Check Engine Light Car Code Reader User Guide
- June 9, 2024
- Foxwell
Table of Contents
QUICK START GUIDE For OBDII/EOBD Code Reader NT204/NT201
QUICK START GUIDE
Shenzhen Foxwell Technology Co., Ltd.
Pictures illustrated here are for reference only and this Quick Start Guide is
subject to change without prior notice. For more details, please refer to the
User’s Manual.
OBD Service Modes
- Mode 1 : Real-time data, M I L , IM monitors.
- Mode 2: Freeze frame.
- Mode 3 : Stored DTCs.
- Mode 4: Clear/Reset DTCs and emissions-related diagnostic information.
- Mode 5 : 02 monitoring tests, supported.
- Mode 6: Test results for continuously and noncontinuously monitored systems, supported.
- Mode 7: Pending DTCs.
- Mode 8: Request control of on-board-system, test or component (bidirectional controls).
- Mode 9: Request VIN and other data.
- Mode 10: Allows a scan tool to obtain permanent codes.
Updating
*No Registration Required / PC : Windows 7, Windows 8 and Windows 10 supported.
Updating
- Download the update tool NT_WONDER and install it.
- Enable NT_WONDER and connect NT204/NT201 to the computer with USB cable.
- Click
or to start updating according to the software version conditions. - An Update Finished Message displays when the update is completed.
NT204/NT201 OBD II /EOBD CODE READER
The NT204/NT201 CAN OBDII/EOBD Code Reader lets car owners troubleshoot
OBDII/EOBD problems on today’s vehicles easily. Its 2.4″ TFT color screen and
hot key for I/M test make it excellent value for money.
Applicable Functions
Read Codes / Freeze Frame Data
On-board Monitor Test / Component Test
Erase Codes / Live Data
Vehicle Information / Modules Present
I/M Readiness / 02 Sensor Test
Unit of measure / DTC GUIDE
How to use NT204/NT201?
Before start diagnosis, please make sure :
- The ignition switch is turned to ON position.
- The engine is off.
- The vehicle battery voltage is between 10-14 volts.
- The scanner is connected to the vehicle correctly.
Don’t connect or disconnect the equipment while the ignition is on or the engine is running.
OBD-II Connector and Pinout
- Vendor Option /
- SAE J1850BUS+ /
- Vendor Option /
- Chassis Ground /
- Signal Ground /
- CAN High(ISO 15765-4) /
- K-Line of ISO 9141-2 and ISO 14230-4 /
- Vendor Option /
- Vendor Option /
- SAE J1850BUS- /
- Vendor Option /
- Vendor Option /
- Vendor Option /
- CAN Low(ISO 15765-4) /
- L-Line of ISO 9141-2 and ISO 14230-4 /
- Battery Power
-
Turn on the ignition of your car.
-
In the main menu, ENTER 08011/EOBD, then NT204/NT201 starts scanning, wait for several seconds, choose “yes/no” with right arrow key, and enter the Diagnostic Menu.
-
Choose “Read Codes”- Choose each selection to check. Pending Codes means the codes need to be confirmed after several driving cycle.
-
Enter “Live Data”, graphing selected live data will also help locate bad sensors.
-
Enter “View Freeze Frame”, which is a snapshot of critical vehicle operating conditions automati-cally recorded by the on-board computer at the time DTC( Diagnostic Trouble Code) set. Check the data which you need to locate bad sensors.
-
02 Monitor Test, On-Board Monitor Test, Component Test, the availability of these tests may depend on the actual condition of your vehicle.
-
Enter “1/M Readiness”.
Retrieve I/M
| Malfunction Indicator Lamp| | Ignition
---|---|---|---
| Diagnostic Trouble Codes| | Pending Diagnostic Trouble Codes
| Misfire| | Evaporative System
| Fuel System| | Intake Air System
| Comprehensive Component Monitor| | Oxygen Sensor
| Catalyst| | Oxygen sensor heater
| Heated Catalyst| | Exhaust Gas Recirculation
Pictures illustrated here are for reference only and this Quick Start Guide is subject to change without prior notice. For more details, please refer to the User’s Manual.
Contact Us
For service and support, please contact us.
Website: www.foxwelltech.us
E-mail : support@foxwelltech.com
Service Number : + 86-755-26697229
Fax: + 86-755-26897226
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>