kopul MUTEMATE-2X2 Momentary Microphone Mute or Talk Switch User Manual
- June 9, 2024
- kopul
Table of Contents
kopul MUTEMATE-2X2 Momentary Microphone Mute or Talk Switch User Manual
Thank you for choosing Kopul
Kopul’s MUTEMATE 2X2 for dynamic and condenser microphones functions as a momentary mute button so an audience, recording talent, or online conferees won’t hear coughs or side conversations.
With the flip of a switch, it becomes a momentary talk button that activates the microphone while the button is pressed.
The MuteMate features 3-pin XLR connectors for mic input and signal output to a recorder, sound system, or audio workstation. Nonslip rubber feet make the MuteMate a handy desktop accessory or foot switch. Mounting holes can be used for more permanent installation on podiums, walls, or workstations.
Precautions
- Please read and follow these instructions, and keep this manual in a safe place.
- Exposure to high sound levels can cause permanenthearing loss. Avoid listening at high volumes for extended periods of time.
- Keep this product away from water and any flammable gases or liquids.
- Clean this product with only a soft, dry cloth.
- All images are for illustrative purposes only
Overview
Operating the MUTEMATE-2X2
Switching from a Condenser to a Dynamic Microphone:
-
Move the selector from Condenser to Dynamic.
-
Then press and hold the mute button for 30 seconds before resuming operation.
This will dissipate the stored phantom power and prevent noise like popping
when activating the button.
Using a Signal Booster for Low-Output Dynamic and Ribbon Microphones:
When using a mic activator, like the Cloudlifter, or an inline mic preamplifier like the Polsen Single-Channel Mic Preamp:
Connect the microphone to the signal booster. Then connect the signal booster
to the MUTEMATE-2X2.
Important! Make sure the MUTEMATE-2X2’s selector switch is set to
Condenser mode when using it with a signal booster connected to a dynamic or
ribbon microphone.
Replacing the Battery
The indicator LED is powered by a 3 V CR 1220 lithium battery. When the battery runs low, the indicator light does not turn on when the button is pressed.
Replace the battery following these steps:
-
Unscrew the four side screws and remove the chassis
. -
Pull back the tension bar with your finger, and the battery will pop up.
-
Remove the battery, place a new CR 1220 3V lithium battery into the battery slot, and press it down until it clicks into place. Unscrew the four side screws and remove the chassis.
Specifications
- Connector 1: 3-pin XLR female input
- Connector 2: 3-pin XLR male output
- Selector Switches: Talk/Mute Dynamic mic/Condenser mic
- Material: Steel
- Dimensions (H × W × D): 2 × 2.3 × 2.4 in. (5.1 × 5.9 × 6.2 cm)
- Weight: 6.9 oz. (197 g)
- Battery Type: CR 1220 3V lithium battery
One-Year Limited Warranty
This KOPUL product is warranted to the original purchaser to be free from defects in materials and workmanship under normal consumer use for a period of one (1) year from the original purchase date or thirty (30) days after replacement, whichever occurs later. The warranty provider’s responsibility with respect to this limited warranty shall be limited solely to repair or replacement, at the provider’s discretion, of any product that fails during normal use of this product in its intended manner and in its intended environment. Inoperability of the product or part(s) shall be determined by the warranty provider. If the product has been discontinued, the warranty provider reserves the right to replace it with a model of equivalent quality and function.
This warranty does not cover damage or defect caused by misuse, neglect, accident, alteration, abuse, improper installation or maintenance. EXCEPT AS PROVIDED HEREIN, THE WARRANTY PROVIDER MAKES NEITHER ANY EXPRESS WARRANTIES NOR ANY IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. This warranty provides you with specific legal rights, and you may also have additional rights that vary from state to state.
To obtain warranty coverage, contact the Kopul Customer Service Department to obtain a return merchandise authorization (“RMA”) number, and return the defective product to Kopul along with the RMA number and proof of purchase. Shipment of the defective product is at the purchaser’s own risk and expense.
For more information or to arrange service, visit www.kopulcables.com or call Customer Service at 212-594-2353. Product warranty provided by the Gradus Group. www.gradusgroup.com KOPUL is a registered trademark of the Gradus Group. © 2023 Gradus Group LLC. All Rights Reserved.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>