milwaukee 58-22-1420d1 Bolt Full Face Shield Instruction Manual

milwaukee 58-22-1420d1 Bolt Full Face Shield

Product Information

The product is a face shield that provides protection against impact hazards, such as metal or wood chips and small flying objects. The shield is impact- resistant but not unbreakable. Personal eye and face protective devices alone should not be relied on to provide complete protection against hazards, but should be used in conjunction with the machine guards, engineering controls, and sound manufacturing and personal safety practices. The shield has a mesh design that allows 62.1% light transmittance and is made of polycarbonate material that blocks over 99.9% UVA, UVB, and UVC rays.

Usage Instructions

• Read all safety warnings and instructions provided before using the product.
• Save all warnings and instructions for future reference.
• Ensure that you are wearing proper protection as per OSHA 1910.133 (in the United States) or CSA Z94.3 (in Canada), your supervisor, or a safety specialist.
• Do not rely on personal eye and face protective devices alone to provide complete protection against hazards.
• Inspect the shield for any signs of damage before each use. Do not use the shield if signs of wear are visible including breakage, gouges, cracks, dents, chalky appearance, discoloration or loss of color, or craze pattern.
• Do not make any modifications to the product.
• Wash mesh shields with mild soap and water, rinse, and dry with a cloth. Do not use ammonia, alkaline cleaners, abrasive cleaning compounds, or solvents when cleaning shields. Use of certain solvents may lower the impact resistance of the shields.
• Do not use the shield for welding with torches or electric (arc) welding. Eyewear with tinted lenses offer limited protection against sun glare or other light sources.
• Only use the face shield with MILWAUKEE MILWAUKEE Hard Hats or Face/M Helmets.
• Exposure to direct sunlight and heat over time can lessen the ability of the face shield to withstand impact and penetration.

USER INSTRUCTIONS

WARNING Read all safety warnings and instructions provided. Save all warnings and instructions for future reference. Failure to follow these instructions and warnings may result in serious and permanent eye injury, including blindness or death.

• Before using this product in an industrial setting, refer to ANSI Z87.1 (in the United States) or CSA Z94.3 (in Canada), your supervisor, or a safety specialist to insure that you are wearing proper protection. Some operations may require machine guards, goggles, face shields, special filter lenses, or other safety equipment.

• This product helps provide limited eye protection from light to moderate impact hazards, such as metal or wood chips and small flying objects. This face shield is impact-resistant but not unbreakable.

• Protective devices do NOT provide unlimited protection. Eye and face protective devices are not substitutes for machine guards and other engineering controls. Personal eye and face protective devices alone should not be relied on to provide complete protection against hazards (such as fragmenting grinding wheels, exploding devices, etc.), but should be used in conjunction with the machine guards, engineering controls, and sound manufacturing and personal safety practices.

• To reduce the risk of injury, always wear ANSI Z87.1 goggles or spectacles along with these products.

• Do NOT use for sports, simulated combat games (e.g., paintball), or recreation such as target shooting and archery.

• Always use both hands to install and remove this product. Do NOT use unless securely attached to hard hat/helmet.

• Examine this product frequently and replace it immediately if there is any sign of damage. Do NOT use shield if signs of wear are visible including breakage, gouges, cracks, dents, chalky appearance, discoloration or loss of color, or craze pattern. Exposure to chemicals can cause damage. Do NOT make any modifications to this product.

• Wash polycarbonate shields with water and pat dry with a lens cloth. Wash mesh shields with mild soap and water, rinse, and dry with a cloth. Do NOT use ammonia, alkaline cleaners, abrasive cleaning compounds, or solvents when cleaning shields. Use of certain solvents may lower the impact resistance of the shields.

• Do NOT use mesh shield for protection against sand or dust.

• Do NOT use for protection against chemical mists, sprays, splashes, or vapors.

• Special Purpose (Tinted) lenses are NOT for use where filter lenses are required.

• Do NOT use near an open flame. Do NOT use for burning, cutting, welding with torches, or electric (arc) welding. Do NOT use this product for protection against laser light. Eyewear with tinted lenses offers limited protection against sun glare or other light sources.

• Do NOT use this face shield if it has sustained an impact. Dispose of it immediately, even if damage is not visible.

• Do NOT alter, pierce, modify, or engrave the face shield.

• Do NOT tamper with assembly screws.

• Do NOT alter the face shield to fit attachments in any way not recommended by the manufacturer.

• Store in a clean, dry area, out of direct sunlight

• Do NOT store face shield in direct sunlight, including the dashboard or rear window shelf of a vehicle, or in extreme heat over 120°F (49°C). Exposure to direct sunlight and heat over time can lessen the ability of the face shield to withstand impact and penetration.
  Mesh light transmittance: 62.1%
  Polycarbonate UV Information: These lenses block over:

  • 99.9% UVA 315-380nm
  • 99.9% UVB 285-315nm
  • 99.9% UVC 200-285nm

CAUTION Only use MILWAUKEE Face/Mesh Shield with MILWAUKEE Hard Hats or Helmets.

FUNCTIONAL DESCRIPTION

1. Twist-lock cover
2. Hard hat/helmet release tab (2)
3. Hard hat/helmet adapter
4. Brim
5. Face shield

SYMBOLOGY

• Hard hat adapter
• Unlock
• Helmet adapter
• Reverse don

SPECIFICATIONS

Face Shield

• Compatible with………………………. MILWAUKEE HARD HATS and HELMETS
• Replacement Brim…………………………………………… Cat. No. 48-73-1448
• Clear Shield……………………………………………………. Cat. No. 48-73-1420
• Gray Shield…………………………………………………….. Cat. No. 48-73-1425
•  Metal Mesh Shield…………………………………………… Cat. No. 48-73-1430

Replacement Shields

• Compatible with……MILWAUKEE HARD HAT and HELMET FACE SHIELDS
• Clear Shield 5 pk…………………………………………….. Cat. No. 48-73-1440
• Clear Shield 10 pk…………………………………………… Cat. No. 48-73-1441
• Gray Shield 5 pk……………………………………………… Cat. No. 48-73-1442
• Gray Shield 10 pk……………………………………………. Cat. No. 48-73-1443

Replacement Metal Mesh

• Metal Mesh Shield 5 pk……………………………………. Cat. No. 48-73-1432
• Metal Mesh Shield 10 pk………………………………….. Cat. No. 48-73-1433

ASSEMBLY

Attaching/Removing Face Shield and Brim

1. To install the brim, turn the hard hat/helmet adapter on both sides in the correct position with hard hat or helmet facing downward. These release tabs will engage in the forward most accessory slots of the hard hat/helmet.

2. Ensure the adapter tabs are adjusted for proper use on hard hat/helmet. If needed, remove the adapter tabs from the brim on both sides. To re-move the adapter, push the unlock tab at the center of the adapter and pull the adapter to separate from the brim.

3. Rotate the adapter with the intended use facing downward. After repositioning, be sure to push the adapters in their respective side firmly back into the brim frame until they securely “click” into position.

4. Once adapters are adjusted properly for the intended application, slide the adapter tabs down through the front accessory slots on the hard hat/helmet until they securely “click” into position.
   NOTE: Face shields are acceptable to use in the reverse don position only on MILWAUKEE Hard Hats that have the reverse don symbol.

5. To remove the brim, turn the hard hat/helmet over to access the inside of the hard hat/helmet. Locate the release tabs where they protrude to the underside of the hard hat/helmet. Press the release tab on both sides and push upwards through the accessory slots of the hard hat/helmet.

6. Pull brim and face shield away from hard hat/helmet.

Replacing the Face Shield

1. Remove the face shield assembly from the hard hat/helmet.

2. On the side covers of the brim, just below the MILWAUKEE logo, locate the lock tab at the back edge of the cover identified by the unlock .

3. Pull the lock tab out away from the face shield; once it is visible, the lock tab and the mating lock feature of the shield are no longer overlapping, rotate the cover component forward without rotating the shield. Repeat this step to both sides of the shield. NOTE: Push the face shield inwards, while pulling the locking tab out, then rotate forward. Pushing on the face shield is critical for removal.

4. With the cover rotated forward, approximately 90 degrees, the shield can be pulled down to separate from the pivot assembly of the brim.

5.  To reinstall a shield to the brim, reverse the procedure. The curved leading edge of the shield as it is inserted in the pivot of the brim ensure the leading edge is slid beneath the lip on the mating surface of the pivot (Fig. 1 and 2).

6. Once the leading edge is fully inserted into the brim pivot, rotate the cover plate backward to the locked position until it securely “clicks” (Fig. 3).

7. After the shield is installed, (Fig. 4) cycle the shield to the full up and full down positions twice to ensure all components are fully engaged. If the shield would dislodge and separate during this step, an error was made during the re-installation. Repeat the shield installation steps again. Ensure the proper position and full engagement of the shield leading edge where it seats in the pivot and cover components.

Using the Headlamp Bracket

1. Install face shield to hard hat/helmet before installing headlamp bracket or MILWAUKEE hard hat light.
2. To install a headlamp, remove manufacturer’s headband from the light.
3. Remove the elastic band from the bracket.
4. Install the headlamp onto the elastic band by weaving the middle section of the band through the opening on the back of the headlamp.
5. Weave the elastic band end loops through the opening of the bracket’s plastic mounting arms. Ensure the headlamp faces outward.
6. Once the headlamp is securely mounted on the bracket, install the bracket onto the hard hat/helmet by gripping the ends and engaging the rails at the front or rear face of the hard hat/helmet. Slide downward towards the brim until it securely “clicks” into place.
7. Pull on the bracket to ensure it is secure on the hard hat/helmet.
8. To remove, place fingers under the top tab, push into the hat to release the latch, and pull upwards.
   NOTE: It is up to the user’s discretion if the headlamp is compatible with other BOLT™ products. If unable to properly install headlamp, use an alternate headlamp.

MILWAUKEE TOOL
13135 West Lisbon Road • Brookfield, WI 53005 USA
58221420d1 03/22
Printed in Taiwan

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>