SUPERDRIVE SV 710 Drive Pro Sport Steering Wheel Instruction Manual

SUPERDRIVE SV 710 Drive Pro Sport Steering Wheel Instruction Manual

Buttons layout

Type| PC (X-Input)| PC (Direct Input) Analog mode| PC (Direct Input) Digital mode
---|---|---|---
Action Keys| A B X Y RB LB RT LT SRSL| 341265871211| 341265871211
D-Pad| up down leftright| up down leftright| Y+ Y-←→
Functions| StartBack| 109| 109
Direction| Left analog stick| Left analog stick| ←/→
Left paddleRight paddle| LBRB| 12| 12
Left pedalRight pedal| LTRT| Y-Y+| Y-Y+
Mode| XBOX button| MODE| MODE
Program| PROG| PROG| PROG

Before the first use

Thank you for purchasing the DRIVE PRO SPORT SV 710. Before using the wheel, please read this instruction manual carefully and keep it for future reference.

Features

• The DRIVE PRO SPORT SV 710 is compatible with PC (X-Input & Direct Input)
• Compatible with Windows 8/10/11
• Direct Input mode includes digital mode and analog mode
• 270 degree steering rotation
• Steering sensitivity control (3 positions)
• 6 programmable keys for tailor made button configuration for use with different racing games
• Dual motors vibration-effect (ONLY WORKS ON COMPATIBLE GAMES)
• Fully analog driving control for more realistic driving experience
• Spring-loaded acceleration and brake control pedals

Default buttons configuration

See table on.

Installation

1. Turn on the PC.
2. Plug the cable of the pedals into the steering wheel.
3. Connect the USB cable of the wheel to any of the USB ports of the PC. A Windows utility starts automatically to install the device. At the end of that operation, the red LED remains on, the wheel is now ready to use.

IMPORTANT: The steering wheel uses the X-Input protocol by default, so it is compatible with the latest games. Some older games use the Direct Input protocol. To switch to Direct Input mode, press and hold the Home/Mode button for 3 seconds, the LED will flash once to indicate the change. This mode will then be used by default. You can switch from one mode to another at any time by holding down the Home/Mode button for 3 seconds.

Direct Input mode

To set up the wheel in Direct Input mode, install the driver before connecting the wheel to the PC: www.superdrive-gaming.com.

Direct Input default mode is analog. Short press the MODE button once to convert to digital mode, the LED turn off.
In the PC control panel, go to Devices / Game Controller Settings / Properties. The DRIVE PRO SPORT SV 710 is identified as a “Controller (LS- USBMX 1/2/3 Steedng Wheel WW1:wenn)” Enter the test interface, and perform function tests on the buttons and axes respectively. The axis can be calibrated in the calibration interface.
Enter the vibration interface, which can be tested by the axes or foot pedal (left and right paddles).

Programming function

You can now play any racing game that use the default button configuration. For other games, you have 2 options to make the right button configuration:

• You can either go to the Options/Controllers menu in the game and create your own configuration. The advantage is that you can save it for later gaming sessions.

IMPORTANT: The DRIVE PRO SPORT SV 710 is identified as a “game controller” in the commands menu of the games. If you wish to modify the button configuration in the game, go to the “game controller” section, not to the “steering wheel” section.

• You can also use the programming function “on-the-go” of the DRIVE PRO SPORT SV 710. It enables you to create the configuration you want without going in the Options menu of the game, but that configuration will not be saved. This wheel has a built-in program function: you can assign a new function to some buttons to make your own driving comfort and experience.

6 keys can be programmed:

• Left paddle
• Right paddle
• Left pedal
• Right pedal
• Gearshift +
• Gearshift —

Programming procedure

• Press PROG button. The red LED will flash fast.
• Then press any of the 6 programmable keys (listed above) to set up a new function. The red

LED will flash slowly.

• Finally press the button that you would like to reassign to the programmable key (o, x, o, L1, R1, L2, R2). The LED turns red again, the key is now programmed.
• Repeat the above steps to program other buttons if necessary.

Reset one programmed key

• Press PROG button. The red LED will flash fast.
• Then press on the programmed key that you would like to reset. The red LED will flash slowly.
• Press the button that you would like to reset again. The LED turns red again, the key is now reset to default.

Reset all the programmed keys

• Press PROG button. The red LED will flash fast.
• Press OPTIONS button for 4 seconds. The LED turns red again, all keys are now reset to default. Sensitivity is also restored to its initial default state (low on PC, medium on consoles). You can also unplug the wheel for resetting the configuration.

Sensitivity adjustment

The sensitivity control is designed for a better steering control adapted to the different types of racing game environments, such as Off-Road, Grand Prix racing, etc. To adjust the sensitiv-ity, move the switch located on the left of the steering wheel.

• Press PROG, the red LED flashes, press the left or right button from the D-PAD, the sensitivity is MID. o Steering angle is small, good for quick turns racing games
• Press PROG, the red LED flashes, press the up button from the D-PAD, the sensitivity is HIGH. o Steering angle is very small, good for very quick turns, corner turning, etc.
• Press PROG, the red LED flashes, press the down button from the D-PAD, the sensitivity is LOW. o Steering angle is normal, adapted to most of the racing games

Troubleshooting

• Before entering the game, please confirm the compatible mode of the game and adjust the steering wheel to the corresponding mode.
• When the steering wheel is plugged into the PC, and the mode light is not on, please re-plug it again, or check whether the steering wheel works normally.
• When the steering wheel does not respond, the PC screen does not move, or the operation in the game is improper, please restart the PC and then insert the steering wheel.

Precautions of uses

• Do not use this product for other purposes than the ones described in this document
• The wheel should not be used in humid places, splashed or be placed near objects filled with liquids, such as vases. After use, keep the wheel in a dry place.
• Never attempt to disassemble or reconstruct it by yourself.
• Do not apply any excessive pressure to the device and do not apply it to violent shock.
• Stop using this unit immediately if you begin to feel tired or if you experience discomfort or pain in your hands and/or arms while operating the product. If the condition persists, consult a doctor.
• Take breaks every 30 minutes.
• Place the wheel away from direct sunlight, excessive heat, fire or extreme cold. Exposure to extreme temperatures may damage the body, the internal circuitry of the device.
• Do not let unattended children play with the wheel. Do not allow children to play with cords. This product contains small parts that may cause choking if swallowed. This product is not intended to be used by children under 3 years of age.

Contact and Customer Support

Please feel free to contact your Subsonic team for more information about the DRIVE PRO SPORT SV 710 or other products in our range of peripherals. [email protected]

Respect the environment

 In order to protect the environment, please do not discard electric/electronic Act. devices and appliances with household garbage. Please take them to a recycling collection centre.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>