SEALEY FSW80 800MM Floor Sweeper Instructions
- June 4, 2024
- SEALEY
Table of Contents
FSW80 800MM Floor Sweeper
Instructions
800MM FLOOR SWEEPER
MODEL NO: FSW80
Thank you for purchasing a Sealey product. Manufactured to a high standard,
this product will, if used according to these instructions, and properly
maintained, give you years of trouble-free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE
OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND
WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE
DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE
INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to the instruction manual
SAFETY
Ensure that the sweeper is only used on hard/dry surfaces.
Ensure that the dirt collection hopper is present and properly seated
before commencing sweeping.
** The sweeper is for indoor use only.
X DO NOT leave the sweeper unattended, where it could become a hazard to
other people or traffic in the sweeping area. For example, in a warehouse
situation.
X DO NOT allow anyone to ride on the sweeper.
X DO NOT use the sweeper for any purpose other than that for which it
was designed.
X DO NOT use the sweeper to clear up hazardous materials or any
material that may attack the plastic chassis of the sweeper.
X** DO NOT use the sweeper on wet surfaces.
INTRODUCTION
Suitable for cleaning any hard floor and ideal for removing dirt, dust, and debris from large surface areas. Features a 4-brush system, consisting of two side brushes and two further brushes set underneath the unit to easily lift debris into the hopper. Fitted with a tubular handle and adjustable castor wheel that raises the sweeper 20mm enabling larger pieces of debris to be swept up.
SPECIFICATION
Model no: …………………………………………………………. FSW70
Hopper capacity: …………………………………………………….. 40L
Operating width:………………………………………………… 800mm
ASSEMBLY
4.1. Lower Handle: Take the lower handle tube and place the slots in the
flattened ends over the threaded spigots on the handle brackets, see fig.1B.
Ensure that the open slots at each end of the lower handle are engaged with
the plain spigot on the mounting brackets. Retain the handle in place by
screwing a black plastic knob onto each threaded spigot.
4.2. Upper Handle: The upper handle has three alternative mounting holes
in the flattened portions of the handle. Align the chosen mounting holes with
the holes in the upper part of the lower handle and insert the supplied coach
bolts through both frames and retain the black plastic knobs supplied as shown
in fig.1A. 4.3. Handle stowage: The handle can be folded down for storage
purposes. Loosen the lower mounting knobs and pull the handle upwards to
disengage the slotted ends from the plain spigots on the mounting brackets.
Hinge the handle forwards and allow it to rest on the body of the sweeper.
4.4. Circular brushes: Attach each brush to its hub using the 6 screws
provided (3 for each brush). Ensure each brush is correctly seated before
tightening. fig.1
4.5. Use: Ensure the handle height is correctly adjusted for the
convenience of the operative. Make sure that the handle fixings are tight and
the dirt fig.2
collection hopper is properly seated within the main body of the sweeper. Work
methodically up and down the area to be swept, ensuring that each `pass’
overlaps the previous one. To ensure the efficiency of the brushes, push the
sweeper at a good, even pace. To capture larger pieces of debris the basic
clearance of the sweeper can be raised a further 20mm by rotating the height
adjuster seen in fig.1 clockwise. Check the hopper regularly by lifting it
out. Empty it if required. Place it back into the sweeper as shown in fig.2.
Periodically, clean the exterior of the sweeper with a damp cloth.
ENVIRONMENT PROTECTION
** Recycle unwanted materials instead of disposing of them as waste. All
tools, accessories, and packaging should be sorted, taken to a recycling
center, and disposed of in a manner that is compatible with the environment.
When the product becomes completely unserviceable and requires disposal, drain
any fluids (if applicable) into approved containers and dispose of the product
and fluids according to local regulations.
Note: It is our policy to continually improve products and as such we
reserve the right to alter data, specifications, and component parts without
prior notice. Important: No Liability is accepted for incorrect use of this
product.
Warranty:** The guarantee is 12 months from the purchase date, proof of
which is required for any claim.
Sealey Group, Kempson Way, Suffolk Business
Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500
01284 703534
sales@sealey.co.uk
www.sealey.co.uk
© Jack Sealey Limited
Original Language Version
FSW70 Issue:2 (H,F) 05/10/21
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>