myFirst FH8006 Headphones AirWaves User Guide
- June 9, 2024
- myFirst
Table of Contents
myFirst FH8006 Headphones AirWaves
Overview
- Multi-function button
- Volume – / Next track
- Volume + / Previous track
- LED indicator
- Charging port
- Speaker
IMPORTANT: Please follow the instructions for proper use. Keep the headphones away from heat sources such as radiators, hot air vents, stoves, or other heat-generating equipment. Do not block the ports of the headset, such as the charging port, LED port, and microphone. To protect your hearing and extend the lifespan of the product, it is not recommended to listen at maximum volume for extended periods of time. If the headset is damaged, please contact our customer service team for assistance.
Connect
Press and hold the multi-function button for 3 seconds. The LED indicator will turn from steady green to flashing white, indicating that the headphones are in pairing mode. Select “myFirst Airwaves” from the list of available connections on your device to pair the headphones. When the pairing is successful, the LED indicator will turn white.
Power on and off
- To turn the headphones on, press and hold the multi-function button for 3 seconds.
- To turn the headphones off, press and hold the multi-function button for 5 seconds.
Calls
- To answer an incoming call, press the multi-function button once.
- To end a call, press the multi-function button once.
- To decline an incoming call, press and hold the multi-function button for 2 seconds.
Controls
- To play or pause, press the multi-function button once.
- To skip to the next track, press and hold the “-” button for 2 seconds.
- To skip to the previous track, press and hold the “+” button for 2 seconds.
- To decrease volume, press the “-” button once.
- To increase volume, press the “+” button once.
- To activate the voice assistant, click the multi-function button three times.
- To reset the headphones, turn them off and hold down the multi-function button for 8 seconds until the white indicator flashes 5 times. This will reset the headphones to their factory settings.
Charging
To charge the headphones, please use the supplied charging cable. The headphones will turn off automatically when charging. During charging, the LED indicator will be red. When the battery is fully charged, the LED indicator will turn off. Please note that the battery performance may decrease over time with repeated charging and use, as is normal for all rechargeable devices.
Specification
- Ear to ear: Width 98.5mm. Ear to neck: Length 130mm
- Weight: 21.5g
- Water resistant: IPX5
- Sensitivity: 85±3dB
- Speaker Diameter: 16.2mm
- Connection distance: 10m
- Battery capacity: 80mAh
- Play time: 18 hours at 60% volume
- Talk time: 7 hours at 60% volume
- Standby time: 90 hours
- Charging time: 2 hours
- Charging port: Type-C
- USB Charging: DC 5V
Regulatory Conformance
Hereby, Oaxis Asia Pte Ltd declares that the radio equipment type FH8506 is in compliance with Directive 2014/53/EU. Note: Observe the national local regulations in the location where the device is to be used. This device may be restricted for use in some or all member states of the European Union (EU).
FCC Compliance Notice
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment .
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>