Neomounts FPMA-D300 LCD Monitor Arm Instructions Manual
- June 9, 2024
- Neomounts
Table of Contents
Neomounts FPMA-D300 LCD Monitor Arm
Before starting assembly
We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step guide to assembly. Some panels are viewed differently from the exploded drawing below, this is for extra clarity. Do not discard any of the packaging until you have checked all the parts and the pack of fittings. If you are missing any of the parts, contact the store from which you purchased your products and the staff will do their best to help you.
Part Check List
ALLEN KEY
CAUTION: Usually, regular cleaning with a clean dry cloth is sufficient, but for stubborn marks wipe over gently with a clean damp cloth. Never use strong detergents or abrasive cleaners as these may damage the surface finish of your furniture. There are many small components used in the construction of this unit. These loose items should be kept away from young children whilst assembling your unit.
Assembly Guide
Remove the 06 pad cover and adhere to the bottom of the metal plate at four corners to prevent slipperily.
Check your LCD panel first to find which VESA standard interface it supports before assembling.
- 75 mm x 75 mm VESA standard interface Secure the arm to the rear of the LCD panel with screws 07.
- 100 mm x 100 mm VESA standard interface Secure 100 x 100 mm plate 04 to the arm with screws 07, then secure the arm to the rear of the LCD panel with screws 07.
The loading weight of the universal joint is initially fixed below 6 kg. Consult the store where you purchased about adjusting weight over 6 kgs.
- Press two sides of 05-L lightly and remove 05-R, and 05-L outwards. Let the cables run through the bottom of the arm and then press cable cover 03 to the arm to fix the cables steady. Assemble 05-L and 05-R back to arm after finishing cable managing.
- Remove the rubber cap 02, and use the Allen key provided to adjust the weight capacity from 3 to 8 kgs. The weight is originally set up at 3 kgs.
ADJUSTMENT: Be sure to adjust the weight in a vertical position as illustrated. Twist the Allen key in a clockwise direction for less weight; counterclockwise direction, more weight. Make sure of the LCD panel weight prior to adjusting the weight according to the instruction.
Panel weight
- 4 kg
- 5-6 kg
- 7-8 kg
Counterclockwise direction
- 4 turns
- 5-7 turns
- 8-10 turns
FAQ’s
What is the Neomounts FPMA-D300 LCD Monitor Arm?
The Neomounts FPMA-D300 LCD Monitor Arm is a mount that allows you to attach your LCD monitor to your desk or wall. It is designed to provide a flexible and adjustable solution for positioning your monitor.
What size monitors can the Neomounts FPMA-D300 LCD Monitor Arm support?
The Neomounts FPMA-D300 LCD Monitor Arm can support monitors up to 27 inches in size, with a maximum weight of 10 kg.
How does the Neomounts FPMA-D300 LCD Monitor Arm attach to my desk or wall?
The Neomounts FPMA-D300 LCD Monitor Arm can be attached to your desk using a clamp or a grommet, depending on your preference. It can also be attached to a wall using a wall mount.
Is the Neomounts FPMA-D300 LCD Monitor Arm adjustable?
Yes, the Neomounts FPMA-D300 LCD Monitor Arm is adjustable. You can adjust the height, tilt, and swivel of the arm to find the best viewing angle for your monitor.
Can the Neomounts FPMA-D300 LCD Monitor Arm rotate?
Yes, the Neomounts FPMA-D300 LCD Monitor Arm can rotate 360 degrees, allowing you to easily switch between landscape and portrait modes.
Is the Neomounts FPMA-D300 LCD Monitor Arm easy to install?
Yes, the Neomounts FPMA-D300 LCD Monitor Arm is easy to install. It comes with all the necessary hardware and instructions for installation and can be installed in just a few minutes.
Can the Neomounts FPMA-D300 LCD Monitor Arm be used with multiple monitors?
No, the Neomounts FPMA-D300 LCD Monitor Arm is designed to hold a single monitor only. If you need to mount multiple monitors, you will need to purchase additional arms.
What is the warranty for the Neomounts FPMA-D300 LCD Monitor Arm?
The Neomounts FPMA-D300 LCD Monitor Arm comes with a 5-year warranty.
What is a Neomounts LCD monitor arm?
A Neomounts LCD monitor arm is a device designed to securely mount an LCD monitor to a desk or other surface, allowing for greater adjustability and flexibility in positioning.
What are the benefits of using a Neomounts LCD monitor arm?
The benefits of using a Neomounts LCD monitor arm include improved ergonomics, increased desk space, and greater adjustability of the monitor for optimal viewing angles.
What sizes of monitors can a Neomounts LCD monitor arm support?
Neomounts LCD monitor arms are available in various sizes and weight capacities to accommodate a range of monitors from 13 inches to 32 inches.
How do I install a Neomounts LCD monitor arm?
Installation instructions will vary depending on the specific model of Neomounts LCD monitor arm but generally involve attaching the mount to the desk or surface and then attaching the monitor to the mount using the included hardware.
Can a Neomounts LCD monitor arm be adjusted?
Yes, Neomounts LCD monitor arms are designed to be adjustable to allow for optimal viewing angles and ergonomic positioning.
Can a Neomounts LCD monitor arm be used for multiple monitors?
Yes, some Neomounts LCD monitor arms are designed to support multiple monitors at once, allowing for greater flexibility in workspace organization.
Is a Neomounts LCD monitor arm compatible with any monitor brand?
Neomounts LCD monitor arms are designed to be compatible with most monitor brands, but it’s always a good idea to check the specific model’s compatibility before purchasing.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>