KOBALT SGY-AIR266 Pro Retractable Hose Reel with Premium Rubber Air Hose Instruction Manual

SGY-AIR266 Pro Retractable Hose Reel with Premium Rubber Air Hose
Instruction Manual

ITEM #5091975
50 ft Pro Retractable
Hose Reel with Premium
Rubber Air Hose
MODEL #SGY-AIR266

PACKAGE CONTENTS

HARDWARE CONTENTS

SAFETY INFORMATION

Please read and understand this entire manual before attempting to assemble, operate or install the product. If you have any questions regarding the product, please call customer service at 888-3KOBALT, 8:00 a.m.- 8:00 p.m., EST, Monday-Sunday. You could also contact us at partsplus@lowes.com.

WARNING

• Improper assembling or operation of this product could result in serious injury or property damage. Read and understand all assembly and operation instructions.
• Never  remove side cover while hose is under tension. Serious injury could occur.
• Do not exceed maximum pressure of 300 PSI. Use compressed air regulated to a maximum  pressure at or below the reated pressure of any attachments to this product.
• Protect your eyes by wearing safety glasses or a face shield when mounting and using this product.
• Keep loose clothing, hair, and jewelry away from moving parts of hose reel.
• Make sure that the product is firmly mounted before pressurizing.
• Rapidly retracting hose could cause injury and property damage. Maintain control of hose as it retracts.
• Keep hose away from sharp edges. Check hose for wear before each use.

PREPARATION

Before assembling the product, make sure there are no missing parts. Compare parts with package contents list and hardware contents list. If any part is missing or damaged,  do not attempt to assemble the product.
Estimated Assembly Time: 10-15 minutes
Tools Required for assembly and installation (not included):

• 3/8″ (10 mm) Wrench
• 3/16″ (5 mm) Allen Wrench
• Sealant Tape
• Drill & 3/8″ Drill Bit
• Pencil
• Level
• 9/16″ (14 mm) wrench

INSTALLATION PREPARATION

1. Using the provided paper template tape it to the location you are going to hang the retractable hose reel. See fig 1.

NOTE
When securing the hose reel assembly to any type of wood, make sure it is thick enough to not only support the hose reel, but the force required to extend and retract the air  hose. See fig 2.
NOTE Ensure there are no live electrical wires or plumbing in the wall at the location you are drilling.

ASSEMBLY INSTRUCTIONS

1. Using the 3/8″ drill bit, drill 4 holes and install the 4 plastic anchors provided. See fig 1.
2. Using the 3/8″ wrench screw 2 of the mounting screws into the lower left and upper right, leaving about 6 mm (1/4-in) between the wall and screw head.
3. Hang the hose reel on these 2 screws. Slide down the screw slid onto the small end of holes on the base plate (D). See fig 2.
4. Tightly tighten the 2 screws to the mounting bracket. See fig 2.
5. Install and tighten down the 2 remaining screws. See fig 3.
6. Wrap 3-5 layers of sealant tape on both male plug ends of the leader hose (C). Screw one end into the air inlet (E). Use a 9/16″ (14mm) wrench to tighten together. See fig 4.
7. Depending on your setup you can either attach a female inlet plug or a female quick disconnect to the other end of the leader hose. See fig 5.
8. Pull out the hose to the desired length (ensure the hose reel is locked as it will not rewind), open the latch on the bumper (H) and move it to the desired location. Re- latch the bumper (H). See fig 6.
9. The roller bracket (I) can be adjusted to the best angle/position for the smoothest operation of hose reel (A) when the hose reel is mounted. Loosen three screws (J) on  each side with 5/16 (5mm) allen Wrench, rotate the roller bracket (I) to the desired position, then tightly tighten the three screws (J) on each side. See fig 7.
   NOTE If the desire angle is larger than 90 degrees, take off 3 screws (J) on each side, rotate the roller bracket to the desire position, and reassemble and tighten the 3 screws.
   WARNING When loosening or removing the screws (J) on each side be careful that the hose reel does not spin freely and cause the hose reel to lose tension.

OPERATING INSTRUCTIONS

1. To extend air hose (B), slowly extend air hose to desired length. The hose reel will make a “clicking” sound as the hose is pulled out. The clicking sound you hear is the  drum locking into place so it will not retract when you let go of the air hose. It may be necessary to pull air hose beyond desired length to keep it from automatically retracting.
2. To retract, slowly pull air hose (B) until clicking stops. While holding the air hose, let the hose automatically draw back until the bumper (I) stops against the hose guide (H).
   NOTE To avoid damaging the hose reel (A), always hold on to air hose (B) while it is rewinding.

CARE AND MAINTENANCE

• Always operate the product with care by following the operating instructions.

TROUBLESHOOTING

If you have any questions regarding the product, please call customer service at 888-3KOBALT, 8:00 a.m.- 8:00 p.m. EST, Monday-Sunday. You could also contact us at partsplus@lowes.com.

adjusted in the best angle/position.
2.  Roller bracket is damaged.| 1.  Adjust roller bracket in the best angle/position.
2.  Replace roller bracket.
Air hose will not retract smoothly.| 1.  Roller bracket is not adjusted in the best angle/position.
2.  Roller bracket is damaged.| 1.  Adjust roller bracket in the best angle/position.
2.  Replace roller bracket.
Air hose will not retract all the way.| 1. Not enough tension on the coil spring.| Pull out approximately 6-ft of hose, and lock hose in place. Remove the bumper (H) from the hose and slide the hose out of hose guide (G) so the hose is hanging loose.
A. To increase tension, wrap the loose hose one time around the reel drum.
B. To decrease tension, unwrap the hose one time from the –  Run the hose back through the hose guide (G) and reattach the hose stopper.
–  Pull the hose out several feet to check the tension.

WARRANTY

This tool is warranted by the manufacturer to the original purchaser from the original purchase date for one (1) year subject to the warranty coverage described herein.
This tool is warranted to the original user to be free from defects in material and workmanship. If you believe that a tool is defective, return the tool, with proper proof of  purchase to the point of purchase. If it is determined that the tool is defective and covered by this warranty, the distributor will replace the tool or refund the purchase price.
This warranty is void if: defects in materials or workmanship or damages result from repairs or alterations which have been made or attempted by others or the unauthorized  use of nonconforming parts; the damage is due to normal wear, damage is due to abuse (including overloading of the tool beyond capacity), improper maintenance, neglect or  accident; or the damage is due to the use of the tool after partial failure or use with improper accessories or unauthorized repair or alteration.
This warranty gives you specific legal rights, and you may also have other rights that vary from state to state.
For warranty questions, call our customer service department at 888-3KOBALT, 8:00 a.m.- 8:00 p.m. EST, Monday-Sunday. You could also contact us at partsplus@lowes.com.

REPLACEMENT PARTS LIST

KOBALT and logo design are trademarks or registered trademarks of LF, LLC. All rights reserved.
ATTACH YOUR RECEIPT HERE
Serial Number
Purchase Date

Questions, problems, missing parts? Before returning to your retailer, call
our customer service department at 888-3KOBALT, 8:00 a.m. – 8:00 p.m.,
EST, Monday-Sunday. You could also contact us at partsplus@lowes.com.
SS22196

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>