KOBALT SGY-AIR264 Manual Reel with Rubber Air Hose Instruction Manual
- June 9, 2024
- Kobalt
Table of Contents
SGY-AIR264 Manual Reel with Rubber Air Hose
Instruction Manual
ITEM #5091973
50-ft Manual Reel with
Rubber Air Hose
MODEL #SGY-AIR264
SGY-AIR264 Manual Reel with Rubber Air Hose
KOBALT and logo design are trademarks or registered trademarks of LF, LLC.
All rights reserved.
ATTACH YOUR RECEIPT HERE
Serial Number…………………………………….
Purchase Date………………………………
Questions, problems, missing parts? Before returning to your retailer, call
our customer service department at 888-3KOBALT, 8:00 a.m. – 8:00 p.m., EST,
Monday-Sunday. You could also contact us at
[email protected]. SS22246
PACKAGE CONTENTS
| PART | DESCRIPTION | QUANTITY |
|---|---|---|
| A | Manual Wind Hose Reel | 1 |
| B | Air Hose (50-ft.) | 1 |
| C | Lead Hose (3-ft.) | 1 |
| D | Wall Mounting Bracket | 1 |
| E | Air Inlet | 1 |
| F | Air Outlet | 1 |
| G | Handle | 1 |
| H | Handle Assembly Hardware | 3 |
| I | Quick Release Pin | 1 |
| J | Manual Brake Pin Lock | 1 |
HARDWARE CONTENTS
**** SAFETY INFORMATION
Please read and understand this entire manual before attempting to assemble, operate or install the product. If you have any questions regarding the product, please call customer service at 888-3KOBALT, 8:00 a.m. – 8:00 p.m., EST, Monday-Sunday. You could also contact us at [email protected].
WARNING
- Improper assembly or operation of this product could result in serious injury or property damage. Read and understand all assembly and operation instructions.
- Do not exceed maximum pressure of 300 PSI.
- Protect your eyes by wearing safety glasses or a face shield when mounting and using this product.
- Keep loose clothing, hair, and jewelry away from moving parts of hose reel.
- Make sure that the product is firmly mounted before pressurizing.
- Keep hose away from sharp edges. Check hose for wear before each use.
PREPARATION
Before assembling the product, make sure all parts are included. Compare parts
with package contents list and hardware contents list. If any part is missing
or damaged, do not attempt to assemble the product.
Estimated Assembly Time: 10-15 minutes.
Tools required for assembly and installation (not included):
- 9/16″ (14 mm) Wrench
- Phillips Screwdriver
- Sealant Tape
- Drill & 3/8″ Drill Bit
- Pencil
- Level
ASSEMBLY INSTRUCTIONS
-
Pull the quick release pin (I) out and turn it 90 degrees to unlock the wall mounting bracket (D). Tap down on the wall mounting bracket to remove from the manual hose reel (A).
-
Pick where you would like to hang the manual hose reel. Take and place the wall mounting bracket (D) against the wall and using a pencil mark the four holes in the bracket. See fig 1.
-
Using a 3/8″ drill bit, drill the 4 holes you marked with the pencil. See fig 2.
NOTE:
If drilling directly into wood then there is no need to use the plastic anchors.
If drilling into dry wall or cement you will need to insert the plastic anchors into the holes. -
Place the wall mounting bracket (D) over the holes (flat side against the wall) and screw in all 4 screws tightly. See fig 3.
-
To hang the manual hose reel, insert the hose reel back plate into slot on the mounting bracket (D). Push down on the hose reel back plate until the hole in the back plate lines up with the quick release pin (I). Pull out the quick release pin (I) and turn it 90 degrees to lock hose reel in place.
-
Attach the handle (G) with supplied handle assembly screws (H) using a 5/16″ (7.9mm) wrench and Phillips screwdriver.
-
Wrap 3-5 layers of sealant tape on both male plug ends on the leader hose (C). Attach one end into the air inlet (E) using a 9/16″ (14mm) wrench to tighten.
OPERATING INSTRUCTIONS
To extend air hose (B), pull out the manual brake pin lock (J) and turn 90
degrees until it locks into the short slot.
To lock the hose reel in place, pull the hose to the desired
length, pull the manual brake pin lock (J) out and turn 90-degrees until it
will lock into the longer slot.
NOTE
Make sure pin is aligned with one of the 3 slots on the drum.
CARE AND MAINTENANCE
Always operate the product with care by following the operating instructions.
TROUBLESHOOTING
If you have any questions regarding the product, please call customer service at 888-3KOBALT, 8:00 a.m. – 8:00 p.m. EST, Monday-Sunday. You could also contact us at [email protected].
WARRANTY
This tool is warranted by the manufacturer to the original purchaser from the
original purchase date for one (1) year subject to the warranty coverage
described herein. This tool is warranted to the original user to be free from
defects in material and workmanship. If you believe that a tool is defective,
return the tool, with proper proof of purchase to the point of purchase. If it
is determined that the tool is defective and covered by this warranty, the
distributor will replace the tool or refund the purchase price.
This warranty is void if: defects in materials or workmanship or damages
result from repairs or alterations which have been made or attempted by others
or the unauthorized use of nonconforming parts; the damage is due to normal
wear, damage is due to abuse (including overloading of the tool beyond
capacity), improper maintenance, neglect or accident; or the damage is due to
the use of the tool after partial failure or use with improper accessories or
unauthorized repair or alteration.
This warranty gives you specific legal rights, and you may also have other
rights that vary from state to state.
For warranty questions, call our customer service department at 888-3KOBALT,
8:00 a.m. – 8:00 p.m. EST, Monday-Sunday. You could also contact us at
[email protected].
REPLACEMENT PARTS LIST
| PART | DESCRIPTION | QTY |
|---|---|---|
| 1 | Lead In Hose | 1 |
| 2 | Handle | 1 |
| 3 | Hardware for Handle | 3 |
| 4 | 50 ft Hose | 1 |
| 5 | Hardware Packs | 1 |
| 6 | Bend Restrictor Spring | 1 |
KOBALT and logo design are trademarks
or registered trademarks of LF, LLC.
All rights reserved.