COSMO Household Compression Dehumidifier Instruction Manual
- June 9, 2024
- Cosmo
Table of Contents
Household Compression Dehumidifier Instruction Manual
Thank you very much for using our products. Please read the user manual carefully before use and keep it for future reference.
IMPORTANT MATTERS
Please read the user manual carefully before use and keep it for future reference.
- Please keep the product away from water, other liquids or flammable detergents, to avoid electric shock and fire.
- Do not spray any flammable materials such as pesticides or perfume around the product.
Wanting
Impact/operation may dub fetal or serious irjuty.
Warning
Improper creak* May duet injoryor darroge b your house and property. etc.| Forbid
---|---
| No Water
| Disassembly Prohibited
| Please Strictly Follow
| Keep Away from Fire Source
The meanings of icons in this manual and on this machine are as shown above.
Warning
Failure to follow the guidelines below will potentially result in electric
shocks or fire
- Do not plug/unplug the power cord to turn on/off the machine.
- Do not use extended power cord or multi-socket terminal board.
- Do not damage or refit the power cord or plug.
- Do not put fingers or sticks into the air inlet or outlet.
- Do not attempt to repair, disassemble or refit this machine.
- Do not place the machine near a heating device (stove or heater, etc.).
- Please wipe the dust on the power plug, and then plug it securely.
- Please use the power socket compatible with the rated voltage of the product.
- In case of any abnormality (such as burning odor), please turn off this machine and unplug the power cord.
- Please read the installation instructions carefully before installing this machine.
- Do not move the machine while it is running.
- Do not use clothes, curtains and other items to cover the air inlet and outlet or air deflector.
- Do not stand on or lean against the dehumidifier.
- Do not place vases and other water containers on the dehumidifier.
- Do not lean the machine against obstacles or walls.
- Do not use the dehumidifier in narrow places such as wardrobe and furniture.
- Do not face the air supply outlet directly toward flammable device
- Do not use the dehumidifier in high temperature or flammable and explosive places.
- Please power off the machine before cleaning and maintenance (Do not use alcohol, gasoline, benzene and other chemical solvents).
- Do not drain water continuously if the temperature around the water pipe is below zero.
- Do not remove the foamed plastics inside the machine.
- Do not clean this machine with water. Do not use this machine in places where it may come into contact with water.
- Do not make the air supply outlet directly face toward people.
- Please unplug the power cord, empty the water tank to air dry it when the machine is not in use for a long time.
- Please place this machine in a stable horizontal place.
- Please empty the tank first, and then hold the handle firmly to move this machine.
- Please insert the water pipe for continuous drainage.
- If it is drained continuously,please check the machine every two weeks.
PRODUCT OVERVIEW
Specifications
| Model | Cosmo |
|---|---|
| Dimension | 295x295x560mm |
| Weight | 12Kg |
| Noise | <20dB |
| Effective Area | 80 m3 |
PRODUCT OVERVIEW
Power ON-OFF Button:
Control power on/off
Fan Speed/Child Lock Button:
Set the running fan speed of the machine: High (H), Low (L), Sleep Long press
3 seconds to activate or cancel child lock function
Humidity Setting/Ionizer Button:
40%, 60%, 80%, Cont (continuous dehumidification). Set the target
environmental humidity. Long press the key, the ionizer light is on, and the
ionizer function is started
Timer Button: Set the shutdown time: 2H, 4H, 8H. Long press the timer key
to activate the WIFI function
WIFI Indicator: The flashing indicator indicates that the machine is
networking (Only the machine with WIFI function will have this indicator).
Timer Indicator: When the indicator is on, it corresponds to the
scheduled shutdown time of the machine, with 2H, 4H and 8H optional.
Relative Humidity Display: Display the ambient humidity value of the
machine. It will display LO if the humidity is smaller than 40%RH, and display
HI if the humidity is greater than 80%RH.
Child Lock Indicator and Sleep Indicator: The child lock indicator
indicates that the dehumidifier is locked. The sleep indicator indicates that
the dehumidifier is in sleep mode.
Running Indicator: When the running indicator is on, it indicates that
the machine is working.
Humidity Button Set the humidity value in 40%, 60%, 80% or Cont.
Fan Speed Indicator: When the corresponding indicator light is on, it
indicates that the Fan is running, with H, L and Sleep options.
Relative Humidity Indicator: When the relative humidity setting button is
switched, the corresponding relative humidity indicator will be on, and the
machine will dehumidify according to the set relative humidity value (40%,
60%, 80%, Cont).
BASIC OPERATIONS
- When turn on the power supply, the machine will beep three times.
- Press power ON/OFF button. After the buzzer beeps once, the machine will enter into the continuous dehumidification state.ln this state, the running indicator and the continuous dehumidification function indicator are on, the double-digit display screen shows the ambient humidity value, and the fan motor runs. Power Button
Dehumidification Humidity Settings
- The machine is in the normal running state when the running indicator is on.
- Four humidity setting modes (40%, 60%, 80%, Cont) are available, and the indicator will be on when the machine runs in the corresponding mode.
WIFI OPERATION (OPTIONAL)
Download and Sign Up
- Scan the QR code on the right and download the “Smart Life” APP. You can also search “Smart Life” to install the APP in the APP Store.
- Open the “Smart Life” APP, click “Sign Up” and sign up your “Smart Life” account with your phone number or email. Next, log in to the APP.
- Open the “Smart Life” APP, click “Add Device” or “+” on the upper right of the APP homepage, and enter the “Add Device” page. At present, two ways are available to manually add and search devices.
https://smartapp.tuya.com/smartlife
Add Devices in Default Mode (Recommended):
In the “Manually Add” interface, select the corresponding product category to
enter the default mode. After entering the WiFi password on the mobile APP
end, select “Next”. In the startup state, long press the machine timing/WiFi
button, at this time, the WiFi indicator will flash quickly. The device
supports two network configuration modes: Click ” 4 in the top right corner of
the default interface to select the default mode and the compatible mode.
Make sure your smart device is powered up and your phone is connected to a Wi-
Fi network. If the WiFi indicator of the machine does not flash after power
on, long press the (timeing/WiFi) button for more than 5s until the WiFi
indicator flashes quickly again (about twice per second), which means that the
device is already available for configuration. And then select the “Indicator
in Quick Flash”, and click “Next”. When “Successfully Add 1 Device” appears,
the connection has been completed and your device will be listed in your APP
list.
- Control devices in compatible mode: If the connection fails in the default mode, users can also add devices in compatible mode. Long press the (timing/WiFi) button for 5s until the indicator flashes slowly, which indicates that the device has been configured in compatible mode.
- Select other methods in the top right corner of the mobile APP afterwards, select the “Compatible Mode” and click “OK. The indicator flashes slowly”. And then click “Next” to go to the WLAN setting interface of the phone, and connect the Wi-Fi network “SmartLife_XXXX”.
- Go back to the “Smart Life” APP and the connection will start automatically. When “Successfully Add 1 Device” appears, the connection has been completed and your device will be listed in your APP list. Now, you can control your smart device through the mobile APP anytime and anywhere (Make sure that both your phone and smart device are connected to the network, and that your router name is changed to SmartLife_XXX).
INTELLIGENT DETECTION
High and Low Ambient Temperature Protection:
- When the temperature and humidity sensor at the machine air inlet detects that the current ambient temperature is greater than or equal to 42 C , the digital tube will keep flashing slowly and display “L3”, and all loads will be turned off. At this time, the machine can be restored after power on again.
- When the temperature and humidity sensor at the machine air inlet detects that the current ambient temperature is less than or equal to 0 C , the digital tube will keep flashing slowly and display “L4”, and all loads will be turned off. At this time, the machine can be restored after power on again.
Refrigerant Leakage Protection: The compression dehumidifier will be
subject to refrigerant leakage detection every 8min when it is working. If the
suspected refrigerant leakage is detected for five consecutive times, only C8
on the digital tube is flashing, and the compressor and the fan motor on the
machine stop. At this time, all buttons do not work, and the buzzer will not
beep.
Cautions:
- When the machine is under refrigerant leakage protection, please unplug the power cord.
- If the protection is activated due to a malfunction of the machine, it can be used normally after troubleshooting (Power on again after unplugging and plugging in the power cord ).
Compressor Stop/Start Protection:
During the operation of the machine, when the whole machine is not powered
down, the compressor, after shutdown, will be delayed for 3min before starting
again (At this time, the wind speed is adjustable). Category I: Within 3min
from the last shutdown, the compressor is in the forced shutdown state, and it
can be started only after it is beyond 3min from the last shutdown. Category
II: The compressor can be started immediately after it is beyond 3min from the
last shutdown.
Cautions:
- If the whole machine is powered down, the compressor can be started immediately after it is powered on again anytime.
- If the machine is in dehumidification or refrigeration operation, you need to take out the tank and then put it back or turn it off and then turn it on again, and the dehumidification will not start until 3min later.
Water Tank Full Automatic Protection:
- When the machine is working, if the tank is full, the compressor and the fan motor will stop working, and only the tank full indicator will be on.
- Take out the tank and pour out the water.
- Put the tank back, and the machine will restart according to the state before the tank is full (Dehumidification will not start until 3min later).
Fault Detection of Temperature and Humidity Sensor:
- When the temperature sensor of the evaporator coil is in an open or short circuit state, the digital tube will display El and flash. At this time, the machine functions normally. The compressor will work for 30min first and then stop for 10min, and repeat this cycle. It will return to normal automatically after troubleshooting.
- When the components of the temperature and humidity sensor are in an open or short circuit state or unable to connect, the digital tube will display E2 and flash. At this time, other buttons except the humidity button will function normally, and it will be enter the Cont mode by default. It will return to normal automatically after troubleshooting.
Automatic Defrosting:
- When the temperature sensor fixed on the evaporator copper tube detects that the temperature is less than -10 C , the machine will enter the automatic defrosting procedure. (The machine will start automatic defrosting after 30min of dehumidification) At this time, the digital tube will display HS, and the machine will automatically return to normal after the end of defrosting.
- When the frost on the evaporator surface has melted, and its temperature is greater than or equal to 2 C and the defrosting time is more than or equal to 10min, the defrosting action stops and the dehumidification function activates.
Fault Detection of Temperature and Humidity Sensor:
- When the power keeps on after pressing the ON/OFF button to shut down, the machine will remember how it worked before shutdown after pressing the ON/OFF button again.
- When the power is cut off after pressing the ON/OFF button to shut down, the machine will work in the initial default mode after pressing the ON/OFF button to power on again.
- When the power is cut off while the machine is working, the machine will work in the initial default mode after pressing the ON/OFF button to power on again.
TROUBLESHOOTING
In case of the following circumstances, please refer to the following solutions:
Category| Display| Fault Cause| Corresponding Product
State| Solutions
---|---|---|---|---
Digital tube| El| Coil temperature sensor or related circuit fault| The
machine can still work, the digital tube d isplays ‘El” and flashes, and all
buttons function normally. It will return to normal automatically after
troubleshooting.| Check the corresponding c ircuit of coil temperature sensor
and replace it
E2| The components of the temperature and humidity sensor are in an open or
short circuit state or unable to connect| The machine can still work, the
digital tube displays “E2” and flashes, other buttons except the humidity
button (Cont by default) function normally. It will return to normal
automatically after troubleshooting.| Check the components of the temperature
and
humidity sensor or replace them
L3| Too high air inlet temperature (242 C)| The digital tube displays “L3” and
flashes,
the compressor stops, and the wind rotor
i
runs at low w nd speed.| It needs to be powered on again before it can be used
normally
L4| Too low air inlet temperature (50C)| The digital tube displays “1.4” and
flashes, the compressor stops, and the wind rotor runs at low wind speed.
HS| The machine enters defrosting mode| The digital tube displays “HS’,
indicating t hat the machine is defrosting.| Normal. After defrosting, the
display will return to normal automatically
| Refrigerant leakage| The machine stops, and the digital tube displays “C8′
and flashes. At this time, none of these buttons work. It can return to normal
after troubleshooting and power on again.| Return to normal only after power
on again
Condition| Causes and Solutions
---|---
Hot air discharged| •The dehumidified air will pass through the hearing
elements. so it will discharge hot air (without refrigeration function). This
is not a fault.
No water in the tank (Small ehumidification capacity)| •Are the temperature
and the humidity too low?
When the indoor temperature and humidity are too low, the dehumidification
ability decreases. Please confirm the current humidity (Because it is dry and
with low humidity in winter, the water in the tank is reduced). This is not a
fault.
Machine stop (no air)| •Does the power plug fall off? Countermeasure: Plug the
power plug into the socket.
•Are the air outlet and inlet blocked? Countermeasure: Remove the objects
blocking the air outlet and inlet.
Water Tank full indicator ON| •Is the tank full? Countermeasure: Empty the
tank and put it back.
•Is the tank installed correctly? Countermeasure: Re-install the tank.
Dehumidification indicator ON| •Is the machine defrosting? Countermeasure:
Wait for the end of defrosting, and it will return to normal afterwards.
Difficult to reach the set humidity| •Is the room too big?
•Do you open doors and windows frequently? Countermeasure: Please try to use
it in a closed room.
•Are you using a gas stove and other devices discharging water vapor?
The current humidity display value of the dehumidifier is different from that
of other humidometers| •The humidity varies from place to place even within
the same room. Please use the humidity display value as a reference.
Air with odor| •When the temperature of the heat exchanger and the cooler is
abnormal, it may emit odor temporarily. This is not a fault.
Noise| Too much noise| •The sound of refrigerant flowing. In case of starting
operation. switching operation and stopping operation, the refrigerant sound
may be emitted before the refrigerant cycle gets stable.
•Is the machine tilted or unstable due to improper positioning?
•Is the filter net blocked? Countermeasure: Refer to the steps in
“Maintenance” for cleaning.
CLEANING AND MAINTENANCE
Wipe the tank and the body with a soft cloth and store the machine in a ventilated and dry environment to prolong its service life. (Do not use corrosive detergents)
If the filter net is blocked by dust, the dehumidification effect will be worse. Please clean it every 2 weeks or so.
- Take out the filter net.
- Clean it with a vacuum cleaner or wash it with water.
- Install the filter net.
Continuous Drainage
When the machine needs to drain continuously, use a proper flexible rubber hose to connect to the drainage hole through the hole of the tank. When the machine is running continuously, the tank will not hold water. This machine can run continuously without causing shutdown protection.
- Extend the pipe from the continuous drainage outlet into the machine.
- In case of continuous drainage, the drainage pipe should be placed flat on the ground. Any part of the drainage pipe should not be folded or warped, and the outlet end of the drainage pipe should not extend below the liquid level of other containers, otherwise, unsmooth drainage or even failure to drainage may occur.
SPECIFICATIONS
REGIONS| CHINA| EUROPE| SOUTH KOREA| NORTH AMERICA|
JAPAN
---|---|---|---|---|---
Model| Cosmo| Cosmo| Cosmo| Cosmo| Cosmo
Daily Dehumidifica -lion Capacity| 12L/D(30t,RH80%)| 12UD(30t,RH80%)|
12IJD(30°C,RH80%)| 121J0(30t,RH80% )| 12L/D(30.C,RH80% )
Nominal Dehumidif -ication Capacity| 0.29kg/h( 27’C,
RH60%)| 0.29kg/h(27t,
RH60%)| 0.29kg/h (27t,
RH60%)| 0.20kg/h (18.33°C.
RH60%)| 0.29kg/h(27t ,
RH60% )
Effective Area(m3)| 80| 80| 80| 80| 80
Dehumidification Mode| 40%,60%,80%,Cont| 40%,60%,80%,Cont| 40%,60%,80%,Cont|
40%,60%,80%,Cont| 40%,60%,80%,Cont
Water Tank Capacity| 3.2L| 3.2L| 3.2L| 3.2L| 3.2L
Moving Mode| Portable| Portable| Portable| Portable| Portable
Noise Decibel| 20db(A)| 20db(A)| 20db(A)| 20db(A)| 20db(A)
Timing| 2h-4h-8h| 2h-4h-8h| 2h-4h-8h| 2h-4h-8h| 2h-4h-8h
Wind Speed| H-M-Sleep| H.M-Sleep| H-M-Sleep| H-M-Sleep| H-M-Sleep
Refrigerant| R290| R290| R134a| R134a| R134a
Rated Vdtage| 220/50HZ| 220/50HZ| 220V 60HZ| 115V,60HZ| 100V 50/60HZ
Rated Power| 158W| 158W| 172W| 154W| 178W
Maximum Power| 205W| 205W| 230W| 242W| 208W
Net Weight| 12kg| 12kg| 12kg| 12kg| 12kg
Gross Weight| 13kg| 13kg| 13kg| 13kg| 13kg
Dimension(mm)| 295’295’560| 295’295’560| 295’295’560| 295’295’560| 295’295’560
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>