SHX37PTC2000LD Ceramic Fan Heater User Manual

SHX37PTC2000LD
Ceramic Fan Heater
User Manual OPERATING MANUAL
CERAMIC FAN HEATER
SHX37PTC2000LD

CONGRATULATIONS!
THANK YOU FOR PURCHASING A PRODUCT FROM SHX.
This product is intended for use in well-insulated areas and for occasional use only.
PLEASE READ THE OPERATING MANUAL CAREFULLY BEFORE BEGINNING ASSEMBLY,, INSTALLATION, OPERATION OR MAINTENANCE. PROTECT YOURSELF AND OTHERS BY FOLLOWING THE SAFETY INSTRUCTIONS. FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY AND/OR PROPERTY DAMAGE AND/OR LOSS OF CLAIMS UNDER WARRANTY.
Intended Use
This appliance is intended exclusively for the heating of domestic living spaces and may not be used for any other purpose.

IMPORTANT INFORMATION ON SAFETY, STANDARDS AND ELECTRICAL CONNECTIONS

1. Use this appliance only in accordance with the guidelines in this operating manual. Any other use not recommended by the manufacturer may result in fire, electrical shock or personal injury.

2. This appliance is intended exclusively for the heating of domestic living spaces and may not be used for any other purpose.

3. Remove the packaging and check that the appliance is not damaged. If you are in doubt, do not use the appliance and contact your dealer.

4. Before connecting to the mains power supply, check that the mains voltage and type matches the information provided on the type plate of the appliance.

5. The electrical socket to which you connect the appliance must not be defective or loose, must be suitable for the current load required, and above all must be reliably earthed.

6. Avoid using an extension cable, because this could overheat and cause a fire.

7. Do not situate the appliance directly beneath a wall power socket. In case of doubt, have your electrical installation checked by a qualified electrician.

8. It is forbidden to adapt or modify the properties of this appliance in any way. Use only replacement parts and accessories recommended by the manufacturer (failure to do so may result in loss of warranty cover).

9. Do not use this heater if it shows visible signs of damage.

10. Do not operate the appliance unattended. Whenever you leave the room, always switch off the appliance.

11. Do not use the appliance in small rooms where people are present who are unable to leave the room by themselves, unless they are under constant supervision.

12. Do not allow children to play with the appliance. Keep children under 3 years away from the appliance unless they are under constant supervision.

13. Keep the packaging materials away from children. If swallowed, these pose a risk of suffocation.

14. The appliance is not suitable for continuous or highprecision operation.

15. Do not use this heater if it has previously been dropped.

16. This appliance is for use in dry indoor spaces only.

17. Do not use the appliance near water or high humidity, e.g. in damp cellars, or hear swimming pools, baths or showers. Make sure that water cannot get into the appliance.

18. Do not use the appliance in close proximity to petrol, gas, oil, alcohol or other explosive or flammable liquids or gases.

19. To minimise the risk of fire, ensure a distance of at least one metre between the air outlet of the appliance and any flammable materials such as:
    a. Pressurised containers (e.g. spray cans)
    b. Furniture
    c. Textiles of any kind

20. This heater should only be operated on a level, stable surface.

21. Never cover the appliance while it is in operation or while cooling down after use.

22. Ensure that no objects come between the appliance and the mounting wall that could touch the heating surface.

23. Always switch the appliance off before unplugging it.

24. Do not pull the mains cable to disconnect the appliance from the mains supply. Always pull by the plug to disconnect the mains cable.

25. Unplug the appliance when you are not using it and before cleaning it or performing any maintenance. Do not allow children to clean or perform user maintenance on the appliance without supervision.

26. To avoid electric shocks, do not touch the plug with wet hands.

Symbol markings on the appliance
Symbol:
Meaning: Attention! Do not cover
The symbol on the device indicates that it is not permitted to suspend any item (e.g. towels, clothing etc.) above the appliance or directly in front of it. To prevent overheating and the risk of fire, the heater must not be covered!
Symbol:
Meaning:
Protection class 2
This symbol indicates that the appliance is classified as protection class 2 (double insulated).
Class 2 appliances are not connected to the earth of the electricity supply. Instead, they feature an enhanced or doubled insulation up to the rated insulation voltage between the live parts and the parts that can be touched. Accordingly, electrically conductive surfaces or other parts that can be touched are isolated by an enhanced or doubled  insulation from live parts.

ATTENTION| RISK OF INJURY
This appliance becomes hot while it is in operation!
Never touch the appliance while it is in operation → this may result in severe BURNS.
---|---
ATTENTION| RISK OF FIRE
Do not cover the appliance while it is in use.
ATTENTION| SAFE DISTANCE
Maintain a safe distance of at least one metre from flammable items such as furniture, curtains, paper and similar.
PLACE OF USE
Position the appliance in such a way that air can flow in and out without hindrance.
RISK OF BURNS
This appliance becomes very hot during use and can cause burns. Take particular care if children or vulnerable persons are present.
RISK OF OVERHEATING
Do not use the appliance in rooms with a volume less than 4m³.

Recycling, disposal and Declaration of Conformity

**| RECYCLING
The packaging materials can be recycled. It is recommended that you dispose of them in separated waste.
---|---
**| DISPOSAL
The pictogram with the crossed out dustbin indicates that electrical and electronic appliances must be disposed of separately from household waste (WEEE). Electrical and electronic appliances can contain harmful and environmentally hazardous materials. Do not dispose of them in unsorted residual waste, but at a registered collection centre for waste electrical and electronic equipment. By doing so, you will help to conserve resources and protect the environment. For further information please consult your dealer or your local authorities. Directive 2012/19/EU
**| DISPOSAL OF BATTERIES**
In accordance with Legislative Decree no. 188 of 20 November 2008 implementing Directive 2006/66/EC on batteries, accumulators and their associated waste, the symbol of the crossed-out dustbin shown on the battery indicates that it is prohibited to dispose of batteries in household waste. Batteries and accumulators contain environmentally hazardous substances. Users are obliged to dispose of used batteries at municipal collection centres or in collectors set up for the purpose. This service is free of charge. This ensures that the legal requirements are complied with and the environment is preserved.
You may find the following symbols on batteries:
Li = battery contains lithium
Al = battery contains alkali
Mn = battery contains manganese
CR 2025 (Li); AA (Al, Mn); AAA (Al, Mn)

DECLARATION OF CONFORMITY
We hereby confirm that this article complies with the essential requirements, regulations and guidelines of the EU. The detailed declaration of conformity can be viewed at any time via following link: https://www.schuss- home.at/downloads
Errata and technical changes reserved.

SCOPE OF DELIVERY

The scope of delivery for the SHX tower heater includes:

• 1× fan heater
• 1× operating manual
• 1× remote control

DESCRIPTION OF THE APPLIANCE

COMMISSIONING

It is very easy and simple to install and operate the SHX fan heater.

1. INSTALLATION

1. Remove the fan heater from the packaging and remove all packaging materials.
2. Check the appliance for possible damage.
3. Unwind the power cable and check it for damage too.
4. Set the fan heater up on a stable, level surface where it will not tip over and which is not heat-sensitive.
5. Now insert the power plug into a suitable power socket.
6. To operate the appliance via remote control, the safety tab on the back of the battery compartment must be pulled out.

ATTENTION
Please follow the instructions on assembling the appliance provided in the safety information section very carefully.
2. DESCRIPTION OF THE CONTROL PANEL AND REMOTE CONTROL
The fan heater functions can be set with the remote control or directly on the appliance using the control panel buttons.
To operate the appliance via the remove control, point it directly at the sensor on the housing to ensure smooth operation.

3. PREPARING THE REMOTE CONTROL
Please follow the steps below to make it operate correctly:

1. To operate the appliance via remote control, please remove the plastic protection from the battery compartment.

2. To change the batteries, carry out the following steps:
   Pull out the battery holder on the back of the remote control, remove the old battery and then insert a new one:

3. Please always pay attention to the polarity markings (+/-) on the battery and the battery holder:

4. Then insert the battery holder back into the remote control.

4. SETTING THE FUNCTIONS
READY-TO-OPERATE MODE:
To set the appliance to ready-to-operate mode, put the ON/OFF switch on the back of the device to ‘I’. The appliance now shows the current temperature on the display.

1. ON/OFF BUTTON
   Use the On/Off button to switch the appliance on and off.
   As soon as you switch on the appliance, the fan begins to circulate air and the symbol appears on the display.
   NOTE
   When you switch off the appliance, it will continue to operate in fan mode for approx. 30 seconds until the appliance has cooled down. The symbol will flash on the display at the  same time.

2. FUNKTION BUTTON
   Set the heating levels with the function button. You can select between a low and a high heating level:
   • Press one time → Low heating level → appears on the display
   • Press two times → High heating level → appears on the display
   • Press three times → Fan function

3. TEMPERATURE BUTTONS
   Use to set the desired target temperature (10°C–35°C).
   Press the button to increase the temperature and the button to decrease the temperature.
   • The symbol is shown from a temperature setting of 31°C and above
   • The symbols are shown from a temperature setting of 33°C and above.
   NOTE
   Please note:
   • The appliance only begins heating when the temperature is set higher than the current room temperature.
   • The appliance automatically switches off when the air temperature is 3°C above the temperature setting.
   • The appliance automatically switches on when the air temperature falls 1°C below the temperature setting.

4. OSCILLATION BUTTON
   The appliance is equipped with an oscillating function. You can use the oscillation button to activate and deactivate this function → This function allows the discharged air to  be distributed to the left and right.

5. TIMER BUTTON
   You can use the timer to switch off the device in a time-controlled manner. Every push of the button increases the timer by 1 hour. The appliance displays the remaining operating time every hour until the fan heater automatically switches off.
   In order to deactivate the timer, repeatedly press the timer button until ‘0H’ appears on the display.

SAFETY FEATURES

The SHX tower heater features two independent protection systems designed to protect the appliance and to minimise the risk of fire.
Please be aware that both mechanisms are not intended to act as an auto-stop or other convenience function. Always switch the appliance off, unplug from the power socket and allow the fan heater to cool before moving, cleaning or putting it in storage.
OVERHEATING PROTECTION
If there is any danger of the appliance overheating (e.g. because something is covering it or due to power supply overload), the built-in overheating protection will switch the appliance off. Once it has cooled, the appliance switches back on automatically and resumes its previous operation.
ATTENTION
A common cause of overheating is among other things the build-up of dust or fluff inside the appliance. You are advised to clean the appliance regularly and to use a vacuum cleaner to remove such build-up.
TIP PROTECTION
There is a special button located on the underside of the appliance which always has contact with the floor as long as the appliance is positioned upright.
Tip protection will activate and switch the appliance off if the appliance is tilted a few degrees from its upright position, the appliance is lifted up, or it is accidentally knocked over.
Once the appliance is positioned upright again on a solid surface, the appliance switches back on automatically and resumes its previous operation.

CLEANING INSTRUCTIONS

Before cleaning the appliance, switch the fan heater off, unplug from the power socket and wait until the appliance has cooled completely.
CLEANING
Clean the appliance with a soft, moderately damp cloth, then wipe with a dry cloth.
AIR FILTER
The air filter is located on the back of the appliance – we recommend cleaning it after every week of operation.
Press the tab down to do this and remove the cover grille. Then remove the filter to clean it. Use a vacuum cleaner to remove the dust accumulated in the filter and the cover grille. If the filter is very dirty, you can immerse it in warm water and rinse it several times.
Before putting the filter back in the appliance, allow it to dry out well after washing.

ATTENTION

• Do not immerse the fan heater in water or other liquids or allow it to come into contact with these.
• Never use benzene, alcohol or solvents to clean the appliance – this could be dangerous.
• Do not spray insecticides or similar agents onto the fan heater.
• Do not use the appliance in wet rooms.
• DO NOT COVER – RISK OF FIRE!

ACTIVITIES AT THE BEGINNING/END OF THE SEASON

ACTIVITIES AT THE END OF THE SEASON

• Switch off the appliance and disconnect the mains plug.
• Carefully empty the water tank.
• Pack away the appliance and store it in a cool, dry place.

ACTIVITIES AT THE START OF THE SEASON

• Check that the power supply cable is in good condition and that the earthing is functioning.
• Follow the installation and safety instructions carefully.

TECHNICAL INFORMATION

Contact addresses for more information and Serviceline:

| Schuss Home Electronic GmbH
Scheringgasse 3, A-1140 Vienna, Austria
Serviceline: +43 (1) 97 0 21
www.schuss-home.at
FB no.: 236974 t / FB court: Vienna

Required data for single-room electrical heating devices

Article number SHX37PTC2000L0

Information| Symbol| Value| Unit| Information| Unit
Heat output| Single-room electric storage heaters only: Method of heat transfer control
Nominal heat output| Pm,| 2.0| kW| Manual control of heat transfer with integrated thermostat| No
Minimum heat output (guideline)| Pm„| 1.| kW| Manual control of heat transfer with feedback of room and/or outside temperature| No
Maximum continuous heat output| Ryax c| 2.0| kW| Electronic control of heat transfer with feedback of room and/or outside temperature| No
Auxiliary current consumption| Fan-assisted heat outlet| No
At
Nominal heat output| elms.| 0.000| kW| Type of heat outpuUroom temperature control
At
Minimum heat output| elmn| 0.000| kW| Single heat output level, no room temperature control
No|
In
standby mode| el,.9| 0.004| kW| Two or more manually settable output levels, no room temperature control| No
| Room temperature control with mechanical thermostat| No
| With electronic room temperature control| Yes
| Electronic room temperature control and timed control through the day| No
| Electronic room temperature control and timed control through the week| No
| Other control options
| Room temperature control with presence detection| No
| Room temperature control with detection of open windows| No
| With remote control option (WiFi)| No
| With adaptive start-up control| No
| With operating time limiter| Yes
| With ball-type sensor| No
Contact information:| Schuss Home Electronic GmbH
Scheringgasse 3 — 1140 Vienna — Austria https://wmv.schuss-home.at/

WARRANTY

By purchasing this SHX quality product, it means you have decided to place trust in durability, reliability and innovation.
For this SHX appliance, we grant a warranty period of 2 years from the date of purchase valid in Austria and Germany!
If, contrary to expectations, service work on your appliance is still necessary during this period, we hereby guarantee either free repairs (spare parts and working time) or (at the discretion of Schuss) that we will replace the product. If it is not possible to either repair or exchange the product for economic reasons, we reserve the right to create a time value credit.
In any case, please contact the customer hotline as a first step (see the operating manual – ‘contact addresses for further information and service line’).
We would like to point out that repair work that has not been performed by authorised contract workshops will immediately terminate the validity of this warranty.
This warranty does not cover:

• Damage due to non-adherence to the operating manual
• Repair or replacement of parts due to normal wear and tear
• Appliances that are used commercially, even in part
• Appliances mechanically damaged due to external influence (any fall(s), impact(s), breakage(s), improper use, etc.) as well as signs of wear and tear of an aesthetic nature
• Appliances that have been improperly treated
• Appliances that have not been opened by our authorised service workshop
• Unfulfilled consumer expectations
• Damage caused by force majeure, water, lightning and overvoltage
• Appliances that have had their type designation and/or serial number on the appliance changed, deleted, made illegible or removed
• Defects due to extreme contamination
• Services outside our contract workshops, the transport costs to either an authorised workshop or to us and back, and the associated risks

We would like to expressly point out that a fixed amount of €60 (indexed basis CPI 2015, June 2020) will be charged within the warranty period in the event of operating errors or if no error has been detected.
The provision of a warranty service (repairs or replacement of the appliance) does not extend the absolute warranty period of 2 years from the date of purchase.
The 2-year warranty is only valid upon presentation of the proof of purchase (must include the name and address of the dealer as well as the complete appliance designation) and the corresponding warranty certificate, on which the appliance type and the serial number (on the box and on both the back and underside of the appliance) are to be noted! Without presenting the warranty certificate, only the legal warranty applies!
We would like to expressly point out that the statutory warranty rights are unaffected by this warranty and continue unabated.
A liability for damage on the part of Schuss Home Electronic GmbH and its vicarious agents only exists in the event of gross negligence or intent. In any event, liability for lost profits, expected but not occurred savings, consequential damage and damage arising from claims of third parties is excluded.

The contact address of the respective service workshop is available on our homepage www.schuss-home.at.
Congratulations on making your choice. We wish you a lot of pleasure with the SHX appliance!
ADDRESS SHX Vertrieb
Type designation:………………………………….
Serial number:……………………………………….
Schuss Home Electronic GmbH
A-1140 Vienna (Austria), Scheringgasse 3
Tel.: +43 (0)1/ 970 21

References

• Welcome to Your New Home Page!
• Home » Schuss Home Electronic
• Home » Schuss Home Electronic
• Redirect Notice
• Home » Schuss Home Electronic
• Downloads » Schuss Home Electronic

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>