tempmate S2 Disposable USB Temperature Data Logger User Manual

: June 9, 2024
: tempmate

Table of Contents

S2 Disposable USB Temperature Data Logger
Read User Manual Online (PDF format)
Download This Manual (PDF format)

S2 Disposable USB Temperature Data Logger

1. Introduction

The tempmate.®-S2 is designed to be mounted on a
broadcast or stationary and measure relevant parameters
such as temperature and optionally relative
humidity. The device records data and stores it on an
internal memory.

2. Intended use

The tempmate.®-S2 is designed to be mounted on
shipments or stationary and to record relevant parameters
as mentioned in the datasheet. Any use or operation
requiring specific requirements and standards not
explicitly mentioned in the data sheet must be validated
and tested at the customer‘s responsibility.

3. tempmate.®-S2 models

models

4. Device description

led indicator

5. Display indicators

Press the Start button repeatedly to call up the individual pages on the device display.

If the start delay is set, this symbol ▶ flashes after a successful start until the time limit has elapsed.

6. Quick Start Guide

start guide

7. Operation and use

STEP 1 Configuration *optional
This step is only necessary if you want to adapt the already pre-installed configuration to your application.

– Download the free tempbase 2 software. – https://www.tempmate.com/de/download/
– Install the tempbase 2 software on your PC.
– Remove the cap and connect the not started logger to your PC.
– Open the tempbase 2 software and select the „Logger Setup“ button (1).
– Make the desired settings and save them on your device using the „Save Parameter“ button (2)
– Remove the logger from your PC and replace the cap securely.

STEP 2 Start logger

– Press and hold the blue button for 5 seconds.
– A successful start is indicated by the green LED on your device flashing 10 times.
– Important: If another or no flashing signal appears, do not use the logger and contact support.

STEP 3 Set mark
– Press the blue button twice in succession to set a mark.
– A successfully set marker is indicated by the word „MARK“ and the number of markers set so far in your display.
– Important: Up to 10 marks can be set per operation.

STEP 4 Stop logger
– Press and hold the blue button for 5 seconds.
– A successful stop is indicated by the red LED on your device flashing 10 times.

Alternative stop modes

Automatic stop (default setting)
o The device will stop automatically when the maximum number of readings in the
data memory is reached and no manual stop is performed beforehand.
o This stop mode works in addition to the manual stop..

Software stop (optional)
o This setting can be made in the tempbase 2 software. (see STEP 1)
o The stop is triggered automatically by connecting the logger to the PC and
opening the software.
o A manual stop is not possible in this configuration.

STEP 5 Manual readout
– Remove the cap and connect the logger to your PC.
– A successful connection is indicated by both LEDs flashing. The abbreviations CSV and PDF appear one after the other in the display.- The logger will automatically open as an external drive on your PC. This process may take a few minutes depending on the amount of data.
– Open the drive and copy the PDF and CSV report stored to a local folder.
– Important: A report is automatically generated as PDF and/or CSV when the device is stopped. The device can still be read out during a running measurement and an intermediate report can be downloaded.

Readout with tempbase 2 software (optional)
– Remove the cap and connect the logger to your PC.
– Open the tempbase 2 software and select the „Export/Import“ button (3).

– Select the desired file format (PDF/XLS/IME) for export and the file location and confirm the download.

8. Important notes

– The configuration of your device cannot be changed during recording.
– If you connect the device to the PC without a manual stop, a temporary stop of the recording is triggered. You can now download an interim report. After disconnecting the device from your PC, the recording will continue automatically.
– Always dispose of devices according to your country‘s regulations.
– Do not place the device in corrosive liquids and do not expose it to direct heat.

Main Technical Specifications tempmate.®-S2 T

Recording Options Single-Use
Dimension [mm] 93 x 47 x 8 mm
Weight [g] 30g
Casing Ecofriendly Hardcase
Battery CR2450 lithium metal button cell battery
Connection Interface USB 2.0, A-Type (integrated)
Display Multifunction LCD
Protection Class IP65
Shelf Life 24 months
Temperature Range –30 °C to 70 °C
Temperature Accuracy ±0.3°C (-20 to 40°C) ±0.5 (others)
Temperature Resolution 0.1 °C
Humidity Range n/a
Humidity Accuracy n/a
Humidity Resolution n/a
Ambient Light Sensor Yes
Memory Capacity (measurements) 32,000 points (T)
Run Time (Logging Interval) Up to 180 days (10 min.) = Standard Model
Other models only on request
Data Export PDF & CSV
Alarm Configuration up to 5 points customizable, single or cumulative
Startup Mode Button
Stop Mode Button or by Software

Other Specifications

Temporary PDF The PDF Report is available at any time
without stopping the Logger
Software PDF reader + optional tempbase 2 Software
Reprogrammable Yes, with optional tempbase 2 Software
Backup-Log-Feature Yes
Custom ID and Travel Description Yes
Calibration Certificate Yes, with 6 points (hardcopy) & PDF in memory
Conformity EN 12830, CE, RoHS
Serial Number Identification Yes

Main Technical Specifications tempmate.®-S2 TH

Recording Options Single-Use
Dimension [mm] 93 x 47 x 8 mm
Weight [g] 30g
Casing Ecofriendly Hardcase
Battery CR2450 lithium metal button cell battery
Connection Interface USB 2.0, A-Type (integrated)
Display Multifunction LCD
Protection Class IP52
Shelf Life 24 months
Temperature Range –30 °C to 70 °C
Temperature Accuracy ±0.3°C (-20 to 40°C) ±0.5 (others)
Temperature Resolution 0.1 °C
Humidity Range 0 – 100 %rH
Humidity Accuracy ±3%rH (20 to 80%rH) ±5% (others, at 25°C)
Humidity Resolution 0.1 %rH
Ambient Light Sensor Yes
Memory Capacity (measurements) 32,000 points (T/rH)
Run Time (Logging Interval) Up to 180 days (10 min.) = Standard Model
Other models only on request
Data Export PDF & CSV
Alarm Configuration up to 5 points temperature and 2 points humidity customizable
Startup Mode Button
Stop Mode Button or by Software

Other Specifications

Temporary PDF The PDF Report is available at any time
without stopping the Logger
Software PDF reader + optional tempbase 2 Software
Reprogrammable Yes, with optional tempbase 2 Software
Backup-Log-Feature Yes
Custom ID and Travel Description Yes
Calibration Certificate Yes, with 6 points (hardcopy) & PDF in memory
Conformity EN 12830, CE, RoHS
Serial Number Identification Yes

Since environmental influences can affect the lifespan of batteries, we recommend that all our products be stored in the conditions
that are optimal for them. In this way, the shelf life given at the time of purchase can be guaranteed.
Optimal storage conditions: +15°C to +23°C / 45% to 75% rH.