TAC 71100B 3 Inch Bull Bar Installation Guide
- June 1, 2024
- TAC
Table of Contents
TAC 71100B 3 Inch Bull Bar
Product Information
Specifications:
- Model: 3 BULL BAR
- Compatibility: 2011-2024 Ford F150 ECOBOOST (Excl. all F150 Raptor models/2020-2022 Diesel models)
- Part Number: 71100B
Product Usage Instructions
Parts List:
- 1 Bull Bar
- 1 Driver/Left Mounting Bracket
- 1 Passenger/Right Mounting Bracket
- 4 12mm x 40mm Bolt Plates
- 8 12mm Lock Washers
- 4 12-1.75mm x 35mm Hex Bolts
- 8 12mm x 32mm OD x 3mm Large Flat Washers
- 4 12mm x 24mm OD x 2.5mm Flat Washers
- 8 12mm Hex Nuts
Installation Procedure:
- Remove contents from the box and verify all parts are present.
- Read instructions carefully before starting installation as cutting may be required.
- For vehicles without Tow Hooks:
- Remove the plastic lower bumper cover.
- Bolt the Brackets to the Bolt Plates on both driver and passenger sides.
- Position the Bull Bar onto the Mounting Brackets and attach using the provided hardware. Do not tighten yet.
- Align and adjust the Bull Bar properly, then tighten all hardware.
Maintenance Instructions:
To protect your investment, wax the product after installing. Regular waxing is recommended to add a protective layer over the finish. Use mild soap for cleaning. For stainless steel finishes, aluminum polish may be used to polish small scratches and scuffs.
Frequently Asked Questions
Q: What should I do if some parts are missing from the package?
A: If any parts are missing, please contact our customer support for assistance in obtaining the missing parts.
Q: Can I install this Bull Bar on a Ford F150 Raptor model?
A: No, this Bull Bar is not compatible with F150 Raptor models. It is designed specifically for Ford F150 ECOBOOST models excluding F150 Raptor models.
3” BULL BAR
2011-2024 Ford F150 ECOBOOST
(Excl. all F150 Raptor models/2020-2022 Diesel models)
PART# 71100B
PARTS LIST
| Qty | Description | Qty | Description |
|---|---|---|---|
| 1 | Bull Bar | 4 | 12-1.75mm x 35mm Hex Bolts |
| 1 | Driver/Left Mounting Bracket | 8 | 12mm x 32mm OD x 3mm Large Flat Washers |
| 1 | Passenger/Right Mounting Bracket | 4 | 12mm x 24mm OD x 2.5mm Flat Washers |
| 4 | 12mm x 40mm Bolt Plates | 8 | 12mm Hex Nuts |
| 8 | 12mm Lock Washers |
PROCEDURE
- REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION. CUTTING MAY BE REQUIRED.
- Vehicles with Factory Tow Hooks
Remove the driver side tow hook by removing the front bolt and loosening the rear bolt, (Figure 1). Slide the tow hook off. Leave the rear bolt in place to hold the double nut plate in the frame and aligned with the holes. NOTE: This Bull Bar is not compatible with the factory tow hooks and tow hooks will not be reinstalled.
Position the driver side Mounting Bracket up to the bottom of the frame, (Figure 2). Slide the Bracket under the rear bolt. Bolt the Bracket in place with the factory tow hook bolts and factory double nut plate. Repeat for passenger side Bracket installation.
Vehicles without Tow Hooks
Remove the plastic lower bumper cover, (Figure 4). Insert (2) 12mm Bolt Plates
through the opening in the open front end of the frame on the driver side and
down through the holes in the bottom of the frame, (Figure 2). Bolt the
Bracket to the Bolt Plates with (2) 12mm x 24mm STD Flat Washers, (2) 12mm
Lock Washers and (2) 12mm Hex Nuts. Snug but do not tighten the hardware at
this time. Repeat for passenger side Bracket installation.
-
With assistance, position the Bull Bar onto the inside of the Mounting Brackets, (Figure 3). Use the included (4) 12mm x 35mm Hex Bolts, (8) 12mm x 32mm Large Flat Washers, (4) 12mm Lock Washers and (4) 12mm Hex Nuts to attach the Bull Bar to the Mounting Brackets. Do not tighten at this time.
-
Align and adjust the Bull Bar properly, and tighten all hardware.
IMPORTANT -Vehicles without Tow Hooks only Temporarily remove the Bull Bar. Hold the plastic cover up in position and trace the outline of the Brackets onto the inside of the cover, (Figures 4 & 5). Use a sharp knife or hacksaw blade to carefully cut the openings for the Brackets. Make small cuts and check the fit often for best results. Once properly trimmed to clear the Brackets, reinstall the cover. Reinstall the Bull Bar as described in Steps 3 & 4. -
Do periodic inspections to the installation to make sure that all hardware is secure and tight.
- To protect your investment, wax this product after installing. Regular waxing is recommended to add a protective layer over the finish. Do not use any type of polish or wax that may contain abrasives that could damage the finish.
- For stainless steel: Aluminum polish may be used to polish small scratches and scuffs on the finish. Mild soap may be used also to clean the Bull Bar.
- For gloss black finishes: Mild soap may be used to clean the Bull Bar.
Driver Side Installation Pictured
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>