Joker Machine 30-333 Indian Scout Brake Lever Installation Guide
- June 10, 2024
- Joker MACHINE
Table of Contents
Joker Machine 30-333 Indian Scout Brake Lever
Product Information
Indian Scout Lever Installation
The Indian Scout Lever Installation kit includes two parts, Part No. 30-333 and Part No. 30-334. The kit is manufactured by Joker Machine, a company located at 2245 Kiowa Blvd N. Ste. 100, Lake Havasu City, AZ 86403. For technical support regarding the installation of the product, you can contact the company at PHONE: 909-596-9690 or by sending an email to sales@jokermachine.com. You can also visit their website at www.jokermachine.com for more information.
Product Installation Instructions
Clutch Lever:
- Remove the lever pivot pin assembly.
- Loosen the clutch perch clamp and remove the clutch cable from the lever.
- Install the new clutch lever with the stock pivot pin assembly.
- Retighten the clutch perch clamp using OEM torque spec.
- Test the clutch before riding.
Brake Lever:
Before starting with the installation of the brake lever, please read the following instructions carefully:
You can make this easy or turn it into something more than you expected. If your stock lever has a piston actuator and your Joker lever doesn’t have a threaded hole, STOP and consult Joker Machine. It is fixable but requires an exchange. Stock piston actuators are hard to get from Indian, so be careful not to destroy the piston actuator.
- Remove the stock brake lever pivot pin assembly. (Loosening of master cylinder bar clamp may be required.)
- Remove the stock piston actuator from the brake lever with a 2.5 mm Allen L Key and install it on the Joker brake lever.
- Install the lever to the master cylinder with the stock brake lever pivot pin assembly.
- Retighten the master cylinder bar clamp if loosened using OEM torque specs.
- Test braking before riding.
Product Components
The product includes a piston actuator and pivot pin assembly. It is made in the USA and has two manufacturing dates: 170802-D and 170803-D. The product is recommended for use in Indian Scout motorcycles.
INDIAN SCOUT LEVER INSTALLATION
Part No. 30-333 & 30-334
For technical support contact Joker Machine
2245 Kiowa Blvd N. Ste. 100, Lake Havasu City, AZ 86403
PHONE: 909-596-9690, FAX:
909-596-9693
sales@jokermachine.com,
www.jokermachine.com
INSTALLATION INSTRUCTIONS
CLUTCH LEVER
- Remove lever pivot pin assembly
- Loosen clutch perch clamp and remove clutch cable from lever.
- Install new clutch lever with stock pivot pin assembly.
- Retighten clutch perch clamp using OEM torque spec.
- Test clutch before riding.
BRAKE LEVER
BEFORE YOU START READ THIS CAREFULLY
You can make this easy or turn it into something more than you expected.
If your stock lever has a piston actuator (shown below) and your Joker lever
doesn’t have a threaded hole (shown below), STOP and consult Joker Machine.
Fixable, but requires an exchange
Stock piston actuators are hard to get from Indian, so be careful not to
destroy the piston actuator.
- Use a 2.5mm Allen L Key. Don’t use a T handle or driver until the actuator is loose.
- Is a right hand thread, threaded from the piston side.
- If the stock piston actuator isn’t coming out, try heating the threaded area. It works and doesn’t ruin the stock lever.
- You can buy a piston actuator from Joker Machine if needed.
-
Remove stock brake lever pivot pin assembly. (Loosening of master cylinder bar clamp may be required)
-
Remove stock piston actuator from brake lever with a 2.5 mm Allen L Key and install on Joker brake lever.
NOTE: Stock piston actuators are hard to get, so be careful not to destroy piston actuator. -
Install lever to master cylinder with stock brake lever pivot pin assembly.
-
Retighten master cylinder bar clamp if loosened using OEM torque specs.
-
Test braking before riding.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>