Knightsbridge NH023AW Single Stainless Steel Recessed LED Wall Light Instruction Manual

Knightsbridge NH023AW Single Stainless Steel Recessed LED Wall Light

Product Information

The NH023AW, NH023B, and NH025AW are products that require careful installation and maintenance. These products are designed to provide high- quality LED luminaires. The installation and maintenance manual provides detailed instructions that should be followed to ensure proper installation and maintenance.

General Instructions

It is important to read the instructions carefully before installation and retain them for future reference and maintenance.
The instructions provided in the manual should be used to aid in the installation of the following products: NH023AW / NH023B /NH025AW.

Safety

Before installing the products, it is important to confirm with the manufacturer of the sensors that they are compatible with LED luminaires. The side and lever off gently (see Fig. 1).Figure 1

WARNING: This product must be disconnected from the circuit if subjected to any high voltage or insulation resistance testing. Irreparable damage will occur if this instruction is not followed.

General

Check local authorities for where facilities exist.

Warranty

The product comes with a warranty. Please refer to the warranty information provided by the manufacturer for details.

International Contact Details

If you have any questions or concerns about the product, please contact the manufacturer at:

• TA
• 02
• ML Accessories Limited LU5 4LT
• www.mlaccessories.co.uk

Product Usage Instructions

Follow the instructions below to properly use the NH023AW,NH023B, and NH025AW products:

1. Confirm with the manufacturer of the sensors that they are compatible with LED luminaires.
2. Refer to Fig. 1 in the manual and gently lever off the side.
3. Ensure that the product is disconnected from the circuit before subjecting it to any high voltage or insulation resistance testing.
4. Check local authorities for where facilities exist.

If you have any questions or concerns about the product usage,please contact the manufacturer at the international contact details provided above.

Product GENERAL INSTRUCTIONS

These instructions should be read carefully and retained after installation by the end user for future reference and maintenance.
These instructions should be used to aid installation of the following products: NH023AW / NH023B / NH025AW

Product SAFETY

• This product must be installed in accordance with the latest edition of the IEE Wiring Regulations (BS7671) and current Building Regulations. If in any doubt, consult a qualified electrician
• Please isolate mains prior to installation or maintenance
• Check the total load on the circuit (including when this luminaire is fitted) does not exceed the rating of the circuit cable, fuse, or circuit breaker
• Please note the IP (Ingress Protection) rating of this product when deciding the location for installation
• This product is for indoor use only
• This product is Class I and must be earthed
• This product is IP20 rated

Product INSTALLATION

Note – If this luminaire is being used in conjunction with an external PIR or sensor, please confirm with the manufacturer of the sensors that they are compatible with LED luminaires.

• Provide power to the required point of installation

• Remove the front plate by placing a medium size flat-head screwdriver in the notch on the side and lever off gently (see Fig. 1)

• Connect the luminaire to the mains supply ensuring the correct polarity is observed:
  L – Live (brown), E – Earth (green/yellow), N – Neutral (blue)

• All earth connections must be made and maintained. Use green/yellow sleeving on earth conductors that are not insulated

• Check all electrical connections are secure with no loose strands of cable

• Fit the unit into a suitable wall box taking care not to compress, damage, or trap any cables, and secure with the screws provided

• Clip the front plate onto the main assembly ensuring the screwdriver notch is at the side

• Switch on and check for correct operation

WARNING
This product must be disconnected from the circuit if subjected to any high voltage or insulation resistance testing. Irreparable damage will occur if this instruction is not followed.

Product GENERAL

• This product contains a light source of energy efficiency class G (NH023AW, NH025AW) to Regulation (EU) No. 2019/2015 and (UK) 2021 No. 1095.

• This product contains a nonreplaceable LED light source and a nonreplaceable control gear

• Clean with a soft dry cloth only, do not use aggressive cleaning products or solvents which may damage the product.

• This product is nondimmable.

• This product should be dismantled for disposal when it reaches the end of its life.
  Please see website for dismantling instructions.

• This product should be recycled in the correct manner when it reaches the end of its life.
  Check local authorities for where facilities exist.

WARRANTY

This product has a warranty of 1 year from date of purchase. Failure to install this product in accordance with the current edition of the IEE Wiring Regulations (BS7671), improper use, or removal of the batch code will invalidate the warranty. If this product should fail within its warranty period, it should be returned to the place of purchase for a free-of-charge replacement. ML Accessories does not accept responsibility for any installation costs associated with the replacement product. Your statutory rights are not affected. ML
Accessories reserve the right to alter product specifications without prior notice.

INTERNATIONAL
CONTACT DETAILS

ML Accessories Limited LU5 4LT
www.mlaccessories.co.uk

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>