tp-link RV10 Lite Robot Vacuum Cleaner User Manual
- June 10, 2024
- tp-link
Table of Contents
RV10 Lite Robot Vacuum Cleaner
User Manual
RV10 Lite Robot Vacuum Cleaner
Setup Videos
Scan QR code or visit: https://www.tp-link.com/support/setup-video/#robot-
vacuum
Overview
Power/Clean
- Press once: Start/pause cleaning.
- Press and hold for 5 seconds: Turn on/off the robot vacuum.
*For the first use, slide the power switch from OFF to ON to turn on.
Dock
- Return to the dock to charge.
Spot Cleaning/Child Lock
- Press once: Start spot cleaning.
- Press and hold for 5 seconds: Turn on/off the child lock.
+ Combination Button
- Press and hold simultaneously for 5 seconds: Enter setup mode to configure network.
- Press and hold simultaneously for 10 seconds: Restore to factory default settings.
LED
- Red: Battery level < 20%; Error
- Orange: Battery level between 20% and 80%
- Green: Battery level > 80%
Robot Vacuum & Mop
Robot Vacuum
Postion the Dock
-
Remove the bottom cover of the dock, connect the power cord to the dock, and then replace the cover.
-
Place the dock on a level surface, flat against a wall, without obstacles within 1.5m (4.9ft) in front and 0.5m (1.6ft) on left and right.
Notes
- To ensure a better user experience, make sure the area is with good Wi-Fi signal.
- Do not place it in direct sunlight. Ensure the area around the dock is free of clutter to improve docking performance.
- To prevent the risk of your robot vacuum falling downstairs, ensure that the dock is placed at least 1.2m (4 ft) away from stairs.
- Always keep the dock powered on, otherwise the robot vacuum will not automatically return. And do not move the dock frequently.
Remove Protective Strip
Remove the protective strips on both sides of the front bumper.
Remove Protective Film
Remove the protective film on the front bumper.
Power On and Charge
-
Slide the power switch from OFF to ON to turn on your robot vacuum.
-
Place the robot vacuum on the charging dock or tap **** to send it back to the dock to charge.
It will return to the dock at the end of a cleaning job and whenever it needs to recharge.
Notes
- When the LED of the charging dock flashes 3 times and then goes out, the charging will begin.
- We recommend that you charge the robot vacuum fully for about 4 hours prior to starting the first cleaning job.
- If the robot vacuum is paused for 10 minutes, it will automatically enter sleep mode and the cleaning job will be canceled.
Download the Tapo App and Connect to Wi-Fi
-
Download the Tapo app from the App Store or Google Play, then log in.
https://www.tapo.com/app/download-
app/ -
Open the Tapo app, tap + icon, and select your model.
Follow the step-by-step instructions to easily set up your robot vacuum.
Troubleshooting & Voice Prompts for Issues: https://www.tp-
link.com/support/faq/3525/
TP-Link hereby declares that the device is in compliance with the essential
requirements and other relevant provisions of directives 2014/53/EU,
2009/125/EC, 2011/65/EU and (EU)2015/863.
The original EU Declaration of Conformity may be found at
https://www.tapo.com/support/ce/.
TP-Link hereby declares that the device is in compliance with the essential
requirements and other relevant provisions of the Radio Equipment Regulations
2017.
The original UK Declaration of Conformity may be found at
https://www.tapo.com/support/ukca/
Safety Information
- Keep the device away from water, fire, humidity or hot environments.
- Do not attempt to disassemble, repair, or modify the device. If you need service, please contact us.
Warning
Avoid replacement of a battery with an incorrect type that can defeat a
safeguard. Avoid disposal of a battery into fire or a hot oven, or
mechanically crushing or cutting of a battery, that can result in an
explosion. Do not leave a battery in an extremely high temperature surrounding
environment that can result in an explosion or the leakage of flammable liquid
or gas; Do not leave a battery subjected to extremely low air pressure that
may result in an explosion or the leakage of flammable liquid or gas.
The instructions shall state the substance of the following:
This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the
appliance.
The appliance is only to be used with the power supply unit provided with the
appliance.
WARNING: For the purposes of recharging the battery, only use the
detachable supply unit provided with this appliance.
(For LiDAR Navigation Robot Vacuum) The appliance contains a 5000mAh lithium-
ion battery; (For Robot Vacuum) The appliance contains a 2600mAh lithium-ion
battery.
This appliance can be used by children aged from 8 years and above and persons
with reduced physical, sensory or mental capabilities or lack of experience
and knowledge if they have been given supervision or instruction concerning
use of the appliance in a safe way and understand the hazards involved.
Children shall not play with the appliance. Cleaning and user maintenance
shall not be made by children without supervision.
Operating Frequency / max output power
2400MHz~2483.5MHz / 20dBm
2402MHz~2480MHz / 10dBm
No restrictions exist in the use of radio frequencies or frequency bands in
all EU member states, EFTA countries, Northern Ireland and Great Britain.
Need some help?
Visit www.tapo.com/support/
for technical support, user guides, FAQs, warranty & more
References
- Anatel — Agência Nacional de Telecomunicações
- Regulatory Compliance | Tapo
- UKCA | Tapo
- Answers to All Your Questions on TP-Link Robot Vacuum
- Support Videos | TP-Link
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>