geemarc CLA7 Neck Loop Amplified Hearing Impaired Instruction Manual
- June 10, 2024
- geemarc
Table of Contents
Neck Loop
GENERAL
The mobile iLoopTM + inductive loopset is for people with hearing aids.
When you use the iLoop +, you can speak directly to the caller by the
microphone inside the system. So, the device works as a wireless system.
Compatible with products equipped with a standard 3.5mm coaxial microphone,
headset socket & with most cellular like iPhone, Blackberry, Samsung etc, and
TM DECT…. in some instances you may need to purchase an adaptor in case the
product does not have a suitable headset socket.
NOTE:
-
Don’t forget to switch your hearing aid to T mode.
-
For Users with a Pacemaker
If you have a pacemaker it is recommended that you speak with your doctor or health advisor before using this product. -
iLOOP™ + can be charged by connecting the USB cable to a PC or standard USB charger.
-
Place the power ON/OFF switch on the side of the unit to OFF position when not in use to avoid discharging the batteries. The batteries can charge when the switch is in OFF position.
-
Any interference or echo when using your iLoop TM + could be due to interference from your telephone’s headset socket. In this case please use the jack adapter that is included in the box.
-
With the device connected to a mobile phone, pressing the ‘Hook On/Off’ button allows you to answer an incoming call.
NOTE:
- OFF: LED is off
- ON: LED is Green
- Low battery: LED is Red
- Battery Charging: LED is Blue
POWER SUPPLY / CONNECTING
The unit needs 2pcs AAA size 1.2V rechargeable NiMH batteries for correct
functioning. The batteries must be charged for about 7 hours before use.
– Open the battery compartment door.
– Insert the batteries supplied with the unit, making sure the polarity is
according to the diagram inside the battery compartment.
– To charge the batteries connect the supplied USB cable to the Micro USB
socket of the unit and then onto the USB of PC or standard power supply.
The blue LED will light up.
– Continue charging until the LED switches OFF.
– Disconnect the USB cable after the charging is complete.
– Connect the iLoop TM + in the 3.5mm headset jack of your mobile telephone.
If it works correctly and answers the call then this means that your socket on
your mobile phone is configured in a way to work in sync with the Geemarc
iLoop+. If you find that TM the iLoop + does not work correctly or if there is
an echo, then please attach the jack included in the gift box to plug into the
3.5mm headset socket.
– You can adjust the volume using the volume knob on the iLoop TM +. The same
instruction regarding the use of the adaptor applies to using the iLoop TM +
with tablets, MP3, kindles etc.
NOTE:
- Always disconnect the plug of the iLoop™ + from the telephone and place the Power On/Off switch on the side of the unit to OFF position, beforeinstalling the batteries.
- When the batteries are discharged, the Red LED will light up. Charge the batteries immediately to avoid damage to the unit or the batteries.
- Check that the microphone/headphone socket is compatible with the 4 contact plug (speaker R & L, common, mic). Otherwise if you encounter some problems you can connect the small jack adapter provided, so as to have compatibility with plug (speaker R & L, mic, common).
- Do not dispose off batteries in household rubbish. Pay attention to the battery regulations regarding battery disposal.
MAKING / RECEIVING CALLS
– Place the loop around your neck. Switch the Power ON/OFF switch on the side
to ON position.
– Switch your hearing aid to T mode. – Press the HOOK ON/OFF button. You are
ready to speak through your iLoop TM +.
– The Green LED will turn ON.
– During the call you can adjust the volume of your device by using the volume
control knob located at the bottom of the iLoop TM +.
NOTE :
- The Breakout connector will release if the unit gets entangled with the cables, so as to avoid injury to the neck. If this happens, plug back the connector in the jack to resume normal operation.
GUARANTEE
From the moment your Geemarc product is purchased, Geemarc guarantee it for
the period of two years. During this time, all repairs or replacements (at our
option) are free of charge.Should you experience a problem then contact our
helpline or visit our website at www.geemarc.com.
The guarantee does not cover accidents, negligence or breakages to any parts.
The product must not be tampered with or taken apart by anyone who is not an
authorised Geemarc representative. The Geemarc guarantee in no way
limits your legal rights. IMPORTANT: YOUR RECEIPT IS PART OF YOUR GUARANTEE
AND MUST BE RETAINED AND PRODUCED IN THE EVENT OF A WARRANTY CLAIM.
The guarantee applies to the United Kingdom only.
DECLARATION : Geemarc Telecom SA hereby declares that this iLoop + is in
compliance with the essential requirements and other relevant provisions of
the Radio and Telecommunications Terminal Equipment Directive 2014/53/UE. TM
The declaration of conformity may be consulted at
www.geemarc.com
RECYCLING DIRECTIVES
Recycling directives: The WEEE (Waste Electrical and Electronic Equipment)
Directive has been put in place so that products at the end of life are
recycled in the best way.
When this product is out of order, please do not put it in your domestic waste
bin. Please use one of the following disposal options:
– Remove the batteries and deposit them in an appropriate WEEE skip. Deposit
the product in an appropriate WEEE skip.
– Or hand the old product to the retailer. If you purchase a new one, they
should accept it.
Thus if you respect these instructions you ensure human health
andenvironmental protection.
For product support and help visit our website at
www.geemarc.com
E-mail: help@geemarc.com
telephone 01707 387602
lines are open 09h00 to 16h00 Mon to Fri
Parc de l’Etoile, 2 Rue Galilée, 59791 Grande-Synthe, France
This product is made in China To Geemarc Telecom
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>