D-Link DGS-1008P 8-Port Gigabit PoE Desktop Switch User Guide
- June 10, 2024
- D-Link
Table of Contents
- D-Link DGS-1008P 8-Port Gigabit PoE Desktop Switch
- Product Information
- Package Contents
- LED Indicators
- Product Usage Instructions
- Connecting the DGS-1008P to Your Network
- Product Troubleshooting
- Setup and Configuration Problems
- CONTENTS
- INTRODUCTION
- PRODUCT SETUP
- MOUNTING
- CONNECTING THE DGS-1008P TO YOUR NETWORK
- LED INDICATORS
- TROUBLESHOOTING
- CONTACTS
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
D-Link DGS-1008P 8-Port Gigabit PoE Desktop Switch
Product Information
The D-Link DGS-1008P is an 8-port gigabit PoE desktop switch that is capable of delivering power to PoE-enabled devices such as network cameras. It has 8 ports operating at 10/100/1000Mbps with 4 PoE+ ports (Ports 1 to 4) with a total PoE budget of 60 W.
Package Contents
- D-Link DGS-1008P 8-Port Gigabit PoE Desktop Switch
- Power Adapter
- Quick Installation Guide
LED Indicators
The LED indicators allow you to monitor, diagnose, and troubleshoot any potential problem within the switch, connection, or attached devices.
LED | Color | Status | Description |
---|---|---|---|
Power | Green | Solid Light | The switch is powered on. |
Link/Act/Speed | Green | Solid Light/Blinking | Connection to a 1000 Mbps |
Ethernet device. The port is
receiving or transmitting data.
Link/Act/Speed| Amber| Solid Light/Blinking| Connection to a 10/100Mbps
Ethernet device. The port is
receiving or transmitting data.
Link/Act/Speed| Off| Light off| No link.
PoE (Ports1 to 4)| Green| Solid Light| The port is successfully connected to a
PoE device and is
powering the device properly.
PoE (Ports1 to 4)| Amber| Solid Light/Blinking/Off| PD device insert but
failure occurs. (PSE can’t provide power
due to PD error, over current or the PoE budget shortage).
PoE Max.| Amber| Solid Light/Blinking/Off| Total power consumption is above
53W. When the PoE power is
available more than 7W, the PoE MAX LED will blink 5 seconds. Total
power consumption is below Power Guard Band (53W).
Product Usage Instructions
Product Setup
-
Install the DGS-1008P in a cool and dry place. Refer to the
Technical Specifications for the acceptable operating temperature
and humidity ranges. -
Install the switch in a site free from strong electromagnetic
source, vibration, dust, and direct sunlight. -
Leave at least 10 cm of space at the left and right-hand side
of the switch for ventilation. -
Visually inspect the power jack and make sure that it is fully
secured to the power adapter. Do not stack any device on top of the
switch.
Connecting the DGS-1008P to Your Network
- Connect one end of an Ethernet cable to any of the numbered ports on the switch, and the other end to a network device or another switch/hub.
- Connect the power adapter to the DC power port on the back of the switch, and plug the power adapter into a surge protector or electrical outlet.
- The switch will automatically detect the Ethernet network speed (10, 100, or 1000 Mbps) and adjust itself accordingly.
Product Troubleshooting
If you encounter any issues during setup or usage, refer to the following troubleshooting tips:
Setup and Configuration Problems
-
What should I do if the power LED does not light up?
Check if the power adapter is connected properly to the outlet or surge protector and the back of the device. -
What should I do if a connected device is not detected?
Ensure the Port LED is illuminated or flashing. If not, try using a new Ethernet cable. -
What should I do if a PoE device is not powered by the DGS-1008P?
Ensure that the PoE device is connected to one of the four PoE enabled ports (1 to 4) and the connected PoE devices do not exceed the maximum power budget of 60 W.
CONTENTS
- DGS-1008P 8-Port Gigabit PoE Desktop Switch
- Power Adapter (54V, 1.2 A)
- Mounting Kit
- 4 Rubber Feet
- Quick Start Guide
If any of these items are missing from your packaging, contact your reseller.
Warning: Using a power adapter with a different voltage rating will damage and void the warranty of this product.
INTRODUCTION
The D-Link DGS-1008P 8-Port Gigabit PoE Desktop Switch is capable of feeding power to Power over Ethernet (PoE) devices such as network cameras. The DGS- 1008P has 8 ports operating at 10/100/1000Mbps with 4 PoE+ ports (Ports 1 to 4) with a total PoE budget of 60 W, making it ideal for home and small office use.
PRODUCT SETUP
BEFORE SETTING UP THE DGS-1008P
Please follow the steps below to set up the switch:
- Install the DGS-1008P in a cool and dry place. Refer to the Technical Specifications for the acceptable operating temperature and humidity ranges.
- Install the switch in a site free from strong electromagnetic source, vibration, dust, and direct sunlight.
- Leave at least 10 cm of space at the left and right-hand side of the switch for ventilation.
- Visually inspect the power jack and make sure that it is fully secured to the power adapter.
Do not stack any device on top of the switch.
MOUNTING
- You may mount the switch on a wall with the included mounting kit. Two mounting slots are provided on the bottom of the switch for this purpose.
CONNECTING THE DGS-1008P TO YOUR NETWORK
A. POWER
Plug the DC power jack into the power port of the DGS-1008P, then plug the other end of the AC power cord into a free outlet or surge protector. The Power LED will illuminate confirming that the device has powered up successfully.
B. PoE PORTS (PORTS 1 – 4)
PoE Ports 1 to 4 support 802.3at for up to 30 W per port for individual usage.
C. GIGABIT ETHERNET PORTS (PORTS 1-8)
These ports offer network speeds of either 10/100Mbps and 1000Mbps and can
operate in half or full-duplex transfer modes. These ports also support
automatic MDI/MDIX crossover, eliminating the need for crossover cables or
uplink ports. Each port can be connected directly to a server, router, or
switch using regular straight-through twisted-pair Ethernet cables.
LED INDICATORS
The LED indicators allow you to monitor, diagnose, and troubleshoot any potential problem within the switch, connection, or attached devices.
LED | Color | Status | Description |
---|---|---|---|
Power | Green | Solid light | Power on |
Off | Power off | ||
Link/Act/Speed | Green | Solid light | Connection to a 1000 Mbps Ethernet |
device.
Blinking| The port is receiving or transmitting data.
Amber| Solid light| Connection to a 10/100Mbps Ethernet device
Blinking| The port is receiving or transmitting data.
Off| Light off| No link
PoE ( Ports1 to 4 )| Green| Solid light| The port is successfully
connected to a PoE
device and is powering the device properly.
Off| No connection to a PoE device
Amber| Blinking| PD device insert but failure occurs.
(PSE can’t provide power due to PD error, over current or the PoE budget shortage).
PoE Max.| Amber| Solid light| Total power consumption is above 53W.
Blinking| When the PoE power is available more than 7W,
the PoE MAX LED will blink 5 seconds.
Off| Light off| Total power consumption is below Power Guard
Band (53W).
TROUBLESHOOTING
SETUP AND CONFIGURATION PROBLEMS
- WHAT SHOULD I DO IF THE POWER LED DOES NOT LIGHT UP?
- Check if the power adapter is connected properly to the outlet or surge protector and the back of the device.
- WHAT SHOULD I DO IF A CONNECTED DEVICE IS NOT DETECTED?
- Ensure the Port LED is illuminated or flashing. If not, try using a new Ethernet cable.
- WHAT SHOULD I DO IF A POE DEVICE IS NOT POWERED BY THE DGS-1008P?
- Ensure that the PoE device is connected to one of the four PoE-enabled ports (1 to 4) and the connected PoE devices do not exceed the maximum power budget of 60 W.
CONTACTS
Türkiye
- Uphill Towers Residence A/99
- Atasehir /ISTANBUL
- Tel: +90 (216) 492-99-99
- Email: info.tr@dlink.com.tr
Moldova
- Chisinau; str.C.Negruzzi-8
- Tel: +373 (22) 80-81-07
- E-mail: info@dlink.md
Belarus
- Minsk, 169 Independence Ave
- Phone: +375 (17) 218-13-65
- E-mail: support@dlink.by
Kazakhstan
- 143, Kurmangazy street, Almaty
- Phosupport@dlink.byne: +7 (727) 378-55-90
E-mail: almaty@dlink.ru
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>