tapo S500D Smart Wi-Fi Dimmer Switch User Guide
- June 10, 2024
- tapo
Table of Contents
Quick Start Guide
Smart Wi-Fi Dimmer Switch
Product Introduction
Tapo smart dimmer switch turns on and dims the lights automatically, saving you effort and electricity bills.
Wire Your Switch
-
Turn off the circuit breaker. Then remove the old wallplate of the wall switch and label the Ground and Neutral wires.
Ground: Usually green or copper.
Neutral: Usually white and not connected to the dumb switch.
Line: Usually black and coming from the circuit breaker.
Load: Usually black. One end is connected to the light.
If you are unsure, consult a qualified electrician. -
Disconnect the wires from the old switch.
-
Identify Line and Load wires.
- Turn on the circuit breaker. Use a voltage detector to identify the
energized wire (Line wire).
Take care to avoid electric shocks.
2) Turn off the circuit breaker. Label the Line and Load wires.
-
Connect the wires to the smart dimmer switch as shown below.
-
Line up the switch with the mounting holes. Secure it with screws.
-
Attach the wallplate and turn on the circuit breaker. Then the wiring is finished.
Set Up Your Switch
STEP 1 DOWNLOAD APP
Get the Tapo app from the App Store or Google Play.
https://www.tapo.com/app/download-app/
STEP 2 SET UP
Tap the + button in the app. Select Switches and then your model. Follow the
step-by-step app instructions to set up your smart switch.
Appearance
Button Explanations
| Decrease or increase the brightness.
---|---
Reset| Press and hold for about 5s to reset Wi-Fi while keeping other
settings.
Press and hold for about 10s to restore your switch to factory default
settings.
Restart| Press to restart your switch.
LED Status
Solid amber | Starting up; disconnected from cloud. |
---|---|
Blinking amber & green | Ready for setup. |
Blinking green | Connecting to Wi-Fi. |
Stay green for 30s | Connected to Wi-Fi. |
Solid red | Disconnected from Wi-Fi. |
Blinking amber | Device resetting. |
White | Light fixture is off. |
Blinking green slowly | Firmware upgrading. |
Specifications
Rating: 120 V~ 60 Hz
Load: 300 W Incandescent, 150 W LED
Operation temperature: 0~40℃
Method of mounting included: Independently mounted (Vertically position only);
Operating control, Type 1 action
Pollution Degree 2, Rated Impulse Voltage 2500 V
Software Class A, NEMA Type 1.Y
CAUTION
High Voltage-Disconnect power supply before servicing
Safety Notice
Before installing, servicing or removing the switch, read and follow all safety precautions including the following:
- CAUTION – Risk of Electric Shock – More than one disconnect switch may be required to de-energize the equipment before servicing. A circuit breaker which disconnects the Line and Neutral conductor simultaneously is suitable. Ensure power is off at the circuit breaker before removing or installing any switch. Use a noncontact voltage tester to ensure the power is off.
- The Smart Switch must be installed and used in accordance with the National Electric Code (NEC) or your local electrical code. If you are unfamiliar with these codes and requirements, or are uncomfortable performing the installation, consult a qualified electrician.
- Do not install the Smart Switch with wet hands or when standing on wet or damp surfaces.
- Install only in a suitable UL Listed outlet box (suitable dimensions: H > 2.95 in./75 mm, W > 1.81 in./46 mm, D > 2 in./51 mm).
- Tighten terminal screws to 13 lbf-in.
Need some help?
Visit www.tp-link.com/support
for technical support, user guides, FAQs,warranty and more information.
©2022 TP-Link 7106509851 REV1.0.0
*Images may differ from your actual product.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>