stalgast 883501 Series Chest Freezing Cabinet Instruction Manual
- June 10, 2024
- stalgast
Table of Contents
883501 Series Chest Freezing Cabinet
Instruction Manual
883501 Series Chest Freezing Cabinet
Thank you for the purchase of our product. Please read this manual carefully
before starting to operate the appliance.
All rights reserved. No part of this manual may be reproduced by photocopy,
printing or in any other way without prior consent from the manufacturer.
Photographs and drawings are furnished by way of example and can vary from the
purchased appliance.
NOTE: Keep the manual in a safe place accessible for the personnel.
The manufacturer reserves the right to change technical parameters of the
appliance at any time without advance notice.
SAFETY INSTRUCTIONS
- Incorrect operation and improper use can result in serious damage to the appliance or personal injury.
- Use this appliance solely for its intended use as described in this manual.
- The manufacturer cannot be held liable for any damage caused by incorrect operation and improper use of the appliance.
- During operating keep the appliance and the plug away from water or other liquids. In case the appliance, as a result of carelessness, has been immersed in water or flooded by water immediately unplug the appliance from the wall socket and prior to further use contact a qualified technician for examination.
- Failure to observe instructions enclosed in this manual may result in the hazard of injury or death.
- Do not let unauthorized opening of the housing of the appliance.
- Do not insert any foreign objects into the housing of the appliance.
- Do not touch the plug and the power cord with damp hands.
- Regularly check the condition of the plug and the cord. If the power cord or the plug is damaged they should be replaced by the Authorized Technical Service personnel. • In case the appliance is dropped or damaged in any other way before turning it on always contact the Authorized Technical Service for examination and repair.
- Any repairs and work on the appliance should be carried out solely by Authorized Technical Service, never by the end user as unauthorized tampering could prove highly dangerous for the user.
- Do not let the cord hang over or touch hot surfaces or sharp edges. Keep the cord away from naked fire. When disconnecting the appliance from the wall socket, pull on the plug, never on the cord.
- Do not let the cord (or extension cord) be inadvertently pulled on or tripped over.
- Check the operation of the appliance during usage.
- This appliance can be used by children in the age of eight and more or by persons with reduced physical, sensory or mental capabilities or lack of knowledge and experience in operating of the appliance, if they have been given supervision or instruction concerning use of the appliance in a safe way by a person responsible for their safety and they understand the hazards involved. Children should not play with the appliance. Children should not perform cleaning or maintenance of the appliance without supervision.
- Always switch off the appliance and unplug the power cord from the wall socket when the appliance is not in use and prior to cleaning operations. The disconnected plug should be sited in a visible place.
- Warning: The appliance’s power will remain ON unless unplugged.
- Turn off the appliance before pulling the plug out of the wall socket.
- Never pull the appliance on the cord.
- It is prohibited to store any explosive substances such as aerosol / flammable gas cans in the appliance.
- WARNING: Do not block or cover any ventilation openings in the equipment casing or in the built-in structure.
- WARNING: Do not use mechanical or any other means to accelerate the defrosting process other than recommended by the manufacturer.
- WARNING: Protect the refrigeration system from damage.
- WARNING: Do not use any type of electrical equipment other than recommended by the manufacturer inside the food storage chamber.
DESCRIPTION AND INTENDED USE OF THE APPLIANCE
- The devices are intended for storage of pre-frozen food products
- the housing of the appliance is made of powder coated stainless steel
GENERAL INFORMATION
The device should be placed on even, stable and fireproof surface. Only proper
leveling of the device will facilitate the flow of the coolant in its cooling
system. The freezer should not be installed in the proximity of heat sources
such as radiators, ovens, stoves etc. Installing the device in such place will
cause the compressor to initiate more often which will negatively influence
lifespan of the freezer and increase electricity usage, if installing the
refrigerator in such place cannot be avoided use additional thermal
insulation. Remember to keep the ventilation outlets uncovered. The device
should be connected to a power source of AC 230V @ 50Hz.
Before cleaning the refrigerator disconnect it from the source of power. If
the device remains empty for an extended period of time, switch it off,
defrost it, clean it, dry it and leave the door open to prevent mould growth
in the device. The food should be stored, only and exclusively, in containers
designed for this purpose.
TECHNICAL SPECIFICATION
Model| Dimensions| Capacity net| Climatic Class|
Temperature| Refrigerant| Power| Voltage
---|---|---|---|---|---|---|---
883101| 580x620x845 mm| 93 l| SN/N/ST/T| ≤-18°C| R600a / 52g| 105W| 230
V / 50 Hz
883201| 950x620x845 mm| 190 l| R600a / 65g| 120 W
883301| 1120x700x845 mm| 282 l| R600a / 75g| 130 W
883401| 1280x790x825 mm| 354 l| R600a / 86g| 110 W
883501| 1660x790x825 mm| 488 l| R600a / 100g| 125 W
The device contains coolant R600a – natural, ecological, flammable gas. Take special care when transporting and installing the device to avoid damaging the cooling circuit. If a leak is revealed, refrain from using devices/items that could cause sparks or fire and ventilate the room. To avoid the formation of a flammable gas mixture in the event of a leak from the refrigeration system, install the device in a room with area of 1m 3 per every 8 g of the coolant. The amount of coolant is given in „TECHNICAL DATA” and on the nameplate.
CONTROL PANEL
- Power supply light on the device
- Device operation light
- Alarm – switches on when the temperature inside the chamber is higher than the set point.
- Temperature regulator knob
5.1. Adjusting temperature
The temperature inside the freezer is maintained by a thermostat. It can be
adjusted with the thermostat knob.
Position 1= highest cooling efficiency
Position 2= lowest cooling efficiency
Temperature inside the freezer depends on the thermostat setting, how often
the lid is opened, how much frozen food is inside and ambient temperature. The
temperature is displayed on the control panel.
Position 7 is used to quickly cool the freezer compartment. After about 24
hours, it is recommended to move to position 4.
5.2. ON /OFF
It is advised that the freezer is cleaned before first use. The freezer should
be switched on about 6 hours before any products are placed inside.
Switching the freezer off
Turn the thermostat knob to „0”. In order to completely deactivate the device
pull the plug from the electrical socket.
5.3. Deicing / defrosting
After extensive use the inside of the freezer can become covered with a thick
layer of frost and ice. It can cause increased power usage. The freezer should
be defrosted regularly.
Before defrosting remove the contents of the freezer and turn thermostat to
„0”.
Remove the plug from the water drainage inside the freezer and the plug on the
right side of the device. Remember that water will flow to the floor. The lid
should be opened during defrosting. Water which remains in the freezer should
be removed with a cloth or sponge. Clean the freezer. Do not use any
mechanical devices or any other artificial chemicals for defrosting.
CLEANING
The inside, walls and equipment of the freezer should be washed with warm
water and a mild detergent.
Do not use cleaning detergents which include sand, acid or chemical
solvents.
Do not use steam cleaning devices.
Be careful when washing the freezer with water. Do not allow any water to
access its electrical parts and ventilation.
After washing wipe the freezer dry.
Ventilation grill should be cleaned regularly with a brush or a vacuum
cleaner. Any lodging of dust will cause higher power usage
While cleaning be careful not to damage any wiring or other elements.
TROUBLESHOOTING
Troubleshooting in case of faults
Problem | Solution |
---|
The appliance does not work,
the display is not illuminated| Check whether the plug is inserted in the
mains socket properly.
Check whether the fuse is not damaged or faulty.
The freezer works too loudly| Check whether the furniture and objects placed
nearby are not vibrated due to the compressor’s operation.
Please note that noise from the refrigerant flow cannot be avoided.
Check whether the appliance is stably positioned on the floor.
The temperature is too high| Check whether a separate external thermometer
shows correct values.
Check whether ventilation system works properly and whether the ventilation
grate is not blocked or dirty.
Check whether too much fresh food has been put into the freezer. Check the
temperature again after 24 hours.
Check whether the freezer is not too close to heat sources.
If the above actions bring no result please order a repair by a specialized service provider.
TRANSPORT AND STORAGE
The device is protected by a protective film, placed on a wooden pallet and packed in a cardboard box.
- A packed unit should be stored in a sheltered environment at an ambient temperature of -25°C/+55°C and humidity of 30-95%
- Do not stack more than 2 devices on top of each other
- Please refer to the data plate on the appliance. In case of damage or loss of the nameplate, replace it immediately. Do not unscrew the safety guards.
- Make sure that the installation site has adequate surface area for proper ventilation and operation. After unpacking, carefully remove the protective film and other safety components applied during transport.
- Place the unit on a flat floor and level with the adjustable feet.
- When lifting the device by means of a jack, the jack must be placed on the outside of the frame; after.
- Transporting the unit, wait about 2 hours before restarting it.
- Secure the door of the appliance with a key lock.
- Do not place the appliance near flammable products, outdoors or in direct sunlight.
DISPOSAL OF THE OLD APPLIANCE
Information for users on the rules concerning proper disposal of electrical and electronic equipment at the end of its life.
- Leave your old equipment in the shop where you purchase a new appliance. Each store is obliged to accept old equipment free of charge if you buy there the new equipment of the same type and in the same quantity. The only condition is to deliver the old equipment to the store at your expense.
- Dispose of your old equipment at a collection point. Information about the location of the nearest collection point can be found on the local website or the notice board of the municipal office.
- Leave the equipment at a service point. If the repair of the equipment is unprofitable or impossible for technical reasons, the service is obliged to accept this appliance free of charge.
- Return the used equipment at the end of its life without leaving your home. If you do not have the time or ability to deliver your equipment to the collection point, you can use the services of specialized companies.
- Remember! Do not dispose of used equipment together with regular waste.
An illegal or incorrect disposal of the product will lead to high penalties
being imposed.
The symbol of a crossed-out rubbish bin on the product, its packaging or its
instruction manual means that at the end of its life the product must not be
disposed of with regular waste. The user is obliged to deliver their used
equipment to a designated collection point for proper processing.
GUARANTEE
The dealer of the appliance is liable under the guarantee. The guarantee does not cover any damage resulting from the build-up of limescale inside the appliance. The guarantee also does not cover: damage caused by external forces such as atmospheric discharge, voltage change, incorrect setting of electrical voltage, power supply from unsuitable power outlet, any mechanical, thermal, chemical damage and defects resulting from them. Furthermore, the guarantee does not cover the replacement of exhaustible parts, namely: light bulbs, rubber elements, heating elements damaged by limescale, glass and other elements that are exposed to any form of wear or usage, for example; burners, rubber units as well as any breakdowns or mechanical damage of the appliance elements caused by incorrect storage, transport, maintenance, installation or operation.
Stalgast Sp. z o.o.
Plac Konesera 9, Budynek O, 03-736 Warszawa
tel.: 22 517 15 75 fax: 22 517 15 77
www.stalgast.com
email: stalgast@stalgast.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>