Knightsbridge BL12ALEDS LED Bulkhead with Microwave Sensor Instruction Manual
- June 10, 2024
- Knightsbridge
Table of Contents
INSTALLATION & MAINTENANCE MANUAL
BL12ALEDS / BL20ALEDS
Instruction Manual
GENERAL INSTRUCTIONS
These instructions should be read carefully and retained after installation by
the end user for future reference and maintenance.
These instructions should be used to aid installation of the following
products: BL12ALEDS / BL20ALEDS
SAFETY
- This product must be installed in accordance with the latest edition of the IEE Wiring Regulations (BS7671) and current Building Regulations. If in any doubt, consult a qualified electrician
- Please isolate mains prior to installation or maintenance
- Check the total load on the circuit (including when this luminaire is fitted) does not exceed the rating of the circuit cable, fuse, or circuit breaker
- Please note the IP (Ingress Protection) rating of this product when deciding the location for installation
- Do not overload this accessory or subject it to conditions outside its rating
- This product is Class II double insulated
- This product is IP54 rated
INSTALLATION
Note – Microwave sensors may not be suitable for all installations, for example enclosed spaces, as they are able to detect movement through non- metallic surfaces like plasterboard and thin doors
- Provide power to the required point of installation (refer to BS7671 for correct cabling methods). Suitable IP rated junction boxes should be used where required
- Rotate the diffuser anti-clockwise and remove (see Fig. 1)
- Remove the fastening screw securing the LED plate and open the LED plate (see Fig. 2)
- Mark the location of the fixing holes and drill the holes ensuring not to infringe with any gas/water pipes or electrical cables
- Feed the mains cable through the rubber grommet to retain IP rating, and secure the baseplate to the surface
- Connect the luminaire to the mains supply ensuring the correct polarity is observed (see Fig. 3): L – Live (brown), E – Earth (green/yellow), N – Neutral (blue). The earth terminal is non-functional and only provided for convenience. The additional L’ – Slave live is able to power additional luminaires. A maximum of 400W LED load can be controlled by the sensor
- efasten the LED plate screw
- Reattach the diffuser by rotating clockwise
- Switch on and check for correct operation
SENSOR DIP SWITCH LAYOUT
Note – The sensor fitted in this luminaire can differentiate between natural daylight and artificial light and will only be activated by natural daylight
WARNING
This product must be disconnected from the circuit if subjected to any high voltage or insulation resistance testing. Irreparable damage will occur if this instruction is not followed.
GENERAL
This product contains a light source of energy efficiency class E to
Regulation (EU) No.
2019/2015 and (UK) 2021 No. 1095.
This product contains a light source which can be replaced by the end user and
a control gear which can be replaced by a professional.
Clean the external surfaces with a damp cloth using a mild solution of
detergent and warm water only, do not use aggressive cleaning products or
solvents which may damage the product.
This product is non-dimmable.
This product should be dismantled for disposal when it reaches the end of its
life. Please see website for dismantling instructions.
This product should be recycled in the correct manner when it reaches the end
of its life.
Check local authorities for where facilities exist.
WARRANTY
This product has a warranty of 3 years from date of purchase. Failure to install this product in accordance with the current edition of the IEE Wiring Regulations (BS7671), improper use, or removal of the batch code will invalidate the warranty. If this product should fail within its warranty period, it should be returned to the place of purchase for a free of charge replacement. ML Accessories does not accept responsibility for any installation costs associated with the replacement product. Your statutory rights are not affected. ML Accessories reserve the right to alter product specification without prior notice.
Manufacturers Declaration of Conformity
For ML Accessories (Knightsbridge)
Electrical products in accordance with CE marking
ML Accessories Ltd. Declare that all products have been designed, manufactured, and tested in accordance with the requirements of the relevant legislation
CE marking legislation
In Accordance with the following Directives:
2014/35/EU
2014/30/EU
2014/53/EU| Low Voltage Directive
EMC Directive
Radio Equipment Directive
---|---
Including Legislation
1907/2006
2015/863
2021/341| REACH
RoHS
ERP
---|---
Safety Standards
Full individual declarations and specific safety standards applicable to
relevant product series can be found on our website
www.mlaccessories.co.uk
We hereby declare that the equipment named above has been designed to comply
with the relevant sections of the above referenced specifications. The product
complies with all essential requirements of the directives.
ML Accessories Ltd. Unit E Chiltern Park, Boscombe Road, Dunstable.
Bedfordshire, LU5 4LT
This declaration becomes invalid if technical or operational modifications are
introduced without ML Accessories Ltd. written consent.
UKCA marking legislation
UK SI 2016 No. 1091
UK SI 2016 No. 1101
UK SI 2012 No. 3032
UK SI 2017 No. 1206
UK SI 2021 No. 1095| Electro Magnetic Compatibility Regulations 2016
The Electrical Equipment (Safety) Regulations 2016
Restriction of the use of Certain Hazardous Substances in Electrical and
Electronic Equipment Regulations 2012
Radio Equipment regulations 2017
The Ecodesign for Energy-Related Products and Energy
Information (Lighting Products) Regulations 2021
---|---
Included Legislation
UK SI 2008 No. 2852
UK SI 2013 No. 3113| UK REACH
WEEE
---|---
Safety Standards
Full individual declarations and specific safety standards applicable to
relevant product series can be found on our website
www.mlaccessories.co.uk
We hereby declare that the equipment named above has been designed to comply
with the relevant sections of the above referenced specifications. The
products comply with all essential requirements of the directives.
ML Accessories Ltd. Unit E Chiltern Park, Boscombe Road, Dunstable.
Bedfordshire, LU5 4LT
This declaration becomes invalid if technical or operational modifications are
introduced without ML Accessories Ltd. written consent.
Supplied By:
(UK) Manufacturer
ML Accessories Ltd, Unit E Chiltern Park, Boscombe Road, Dunstable LU5 4LT,
www.mlaccessories.co.uk
(EU) Authorised Representative
nnuks Holding GmbH, Niederkasseler Lohweg 18,
40547 Düsseldorf, Germany,
Email: eprel@nnuks.com AKJUL22_V2
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>