VESTEL 17WFM26 WiFi Bluetooth Combo Module User Manual
- June 10, 2024
- VESTEL
Table of Contents
- 17WFM26 WiFi Bluetooth Combo Module
- Product Information
- Features
- Key Specifications
- Electrical Specifications
- Product Usage Instructions
- General Description
- Features
- Electrical Specification
- RF Characteristic
- Antenna Characteristic
- Mechanical Characteristics
- Pin Description
- Block diagram
- Environmental
- Hardware & Software installation
- FCC Statement
- Software Installation
- Country Regulations
- List of applicable FCC-rules
- On TX/RX page
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
17WFM26 WiFi Bluetooth Combo Module
Product Information
The 17WFM26 WI-FI + BT combo module is a highly integrated MIMO wireless LAN (WLAN) and BT solution that lets users enjoy digital content via wireless technology and connect wireless sound devices, HID devices, BT remote controllers, etc. It is built with WI-FI 2T2R and Bluetooth v5.1 with Low Energy (LE) capable RF/baseband single chip. The card is based on MediaTek MT7663BUN solution.
Features
- IEEE 802.11a/b/g/n/ac Dual Band WLAN standards
- Support for 20/40MHz bandwidth in 2.4GHz and 20/40/80MHz bandwidth in 5GHz bands
- Bluetooth 5.1 with BLE
- Support for Dual band 2T2R mode
- USB2.0 interface
- Printed PIFA antennas (WLAN Printed Antennas, BT Printed Antenna)
- External antenna option with UF.L micro coax RF socket (with BOM option)
Key Specifications
- Main chipset: MT7663BUN, Mediatek
- Frequency range: WLAN – 2402-2482MHz, 5180-5320MHz, 5500-5700MHz; Bluetooth – 2402-2480MHz
- Channels support: WLAN – CH1-13, CH36-64, CH100-140; Bluetooth – CH0-78
- Host interface: USB 2.0
- Operating temperature: 65 degree. Tj max 125 degree for wifi/BT SOC.
Electrical Specifications
-
* Power supply voltages:
- DC supply to module VCC Min: 4.75V
- DC supply to module VCC Typ: 5V
- Current consumption:
| Idle (mA rms)| Max (mA rms)| Max peak (A)
---|---|---|---
2.4G, HT20, Ch6, Rx mode| 83.14| 153.3| 1.2
2.4G, HT20, Ch6, Tx mode| 276| 330.6| 1.208
2.4G, HT20, Ch6, Rx mode + BT| 181.3| 475| 1.272
2.4G, HT20, Ch6, Tx mode + BT| 330.6| 513| 1.248
Idle (5G, VHT20, Ch48)| 96.74| 160.6| 1.44
5G, VHT20, Ch48, Rx mode| 160.6| 475| 1.336
5G, VHT20, Ch48, Tx mode| 104.9| 513| 1.24
5G, VHT20, Ch48, Tx mode + BT| 217.8| | 1.38
Idle (5G, VHT80, Ch108)| | 405.2| 1.38
5G, VHT80, Ch108, Rx mode| | 234| 1.44
- Idle means it is connected to an access point but no data streaming.
Product Usage Instructions
The 17WFM26 WI-FI + BT combo module can be used to connect wireless sound devices, HID devices, BT remote controllers, etc. Follow the steps below to use the product:
- Insert the module into a USB 2.0 port.
- Install the drivers for the module on your computer.
- After the first boot up, select the country information to enable supported channels/frequencies according to country regulations.
- Connect to an access point to stream data wirelessly.
General Description
The 17WFM26 WI-FI + BT combo module design is a highly integrated MIMO wireless LAN (WLAN) and BT solution to let users enjoy the digital content via the wireless technology and connect wireless sound devices, HID devices, BT remote controller etc. The card is built with WI-FI 2T2R and Bluetooth v5.1 with Low Energy (LE) capable RF/baseband single chip. 17WFM26 is based on MediaTek MT7663BUN solution.
Features
- IEEE 802.11a/b/g/n/ac Dual Band WLAN standards
- Support 20/40MHz bandwidth in 2.4GHz and 20/40/80MHz bandwidth in 5GHz bands
- Bluetooth 5.1 with BLE
- Support Dual band 2T2R mode
- USB2.0 interface
- Printed PIFA antennas (WLAN Printed Antennas, BT Printed Antenna)
- External antenna option with UF.L micro coax RF socket (with BOM option)
Electrical Specification
Power supply voltages
DC supply to
module
| Min| Typ| Max
---|---|---|---
VCC| 4.75 V| 5 V| 5.25
Current consumption
Note (VCC 5V) | Typ (mA rms) | Max peak (A) |
---|---|---|
Idle (2.4G, HT20 , Ch6) * | 83,14 | 1,096 |
2.4G, HT20, Ch6, Rx mode | 153,3 | 1,200 |
2.4G, HT20, Ch6, Tx mode | 276 | 1,208 |
2.4G, HT20, Ch6, Rx mode + BT | 181,3 | 1,272 |
2.4G, HT20, Ch6, Tx mode + BT | 330,6 | 1,248 |
Idle (5G, VHT20, Ch48) * | 96,74 | 1,44 |
5G, VHT20, Ch48, Rx mode | 160,6 | 1,3 |
5G, VHT20, Ch48, Tx mode | 475 | 1,336 |
5G, VHT20, Ch48, Tx mode + BT | 513 | 1,44 |
Idle (5G, VHT80, Ch108) * | 104,9 | 1,24 |
5G, VHT80, Ch108, Rx mode | 217,8 | 1,38 |
5G, VHT80, Ch108, Tx mode | 405,2 | 1,38 |
--- | --- | --- |
5G, VHT80, Ch108, Rx mode + BT | 234 | 1,44 |
Thermal characteristics
Operating temperature is 65 degree. Tj max 125 degree for wifi/BT SOC.
RF Characteristic
Wi-Fi
Typical power levels for wi-fi radio are given in figure below.
Bluetooth
Typical power levels for BT radio are given in figure below.
Standard | Bluetooth 5.1 |
---|---|
Modulation | FHSS/ GFSK, pi/4‐DQPSK, 8DPSK |
Data Rate | 1Mbps(GFSK),2Mbps(pi/4‐ DQPSK),3Mbps (8DPSK) |
Channel | CH 0 ~ 78 |
Power (dBm) +/- 3 | 4 dBm |
Sens. Power Level (dBm) +/-3 | -93,5(1DH5)/-87(3DH5) |
Antenna Characteristic
Module has on board printed antennas with the given gain values in below. It can support also external antenna option with UF.L micro coax RF socket (with BOM option).
Onboard Printed Antenna Gains
| ****
2.4 Ghz
| 5 Ghz low band (5180 to 5320 )
(ch 36-64)
| 5 Ghz medium band (5500 to 5700) (ch100-140)| 5 Ghz high band (5745 to 5825)
(ch149-165)
---|---|---|---|---
Antenna 0| 3,4 dBi| 2,97 dBi| 3,69 dBi| 2,89 dBi
Antenna 1| 2,12 dBi| 3,7 dBi| 3,68 dBi| 2,83 dBi
BT| 0,29 dBi| | |
Mechanical Characteristics
Module dimension is 70×25 mm.
Pin Description
Pin No. | Pin Name | I/O | Pin Description |
---|---|---|---|
1* | PW_RST | I/O | Stepdown Enable Control Signal |
2 | WoWLAN | I/O | Wake on Wireless LAN Control Signal |
3 | GND | – | Ground |
4 | GND | – | Ground |
5 | USB_DP | I/O | USB Communication Signal |
6 | USB_DN | I/O | USB Communication Signal |
7 | VCC | I | VCC 5V |
8 | VCC | I | VCC 5V |
Optional and depend on BOM and mother board. PW_RST signal disables 5V -> 3.3V regulator, can be used for power down and hard reset of module.
Block diagram
Environmental
Operating
- Operating Temperature: 0 to 65 °C
- Relative Humidity: 5-60% (non-condensing)
Storage
- Temperature: -20 to 80 °C
- Relevant Humidity: 5-85% (non-condensing)
Hardware & Software installation
Hardware Installation
The module is a build in module. It will be used in-house production as an embedded device over USB 2.0 interface and there is no need any interaction with end-user. Positioning of the module is defined by assembly operator instructions for each product by Vestel. The WI-FI + BT combo module should be mounted by considering operating temperature. The temperature of the installation location should be between 0°C and 65 °C. The module can be installed in mobile or fixed hosts and must meet the RF exposure compliance separation distance of “20cm” between the user / bystander and the antenna. The implementation of the module in a specific end-product should also be reviewed to ensure compliance with the FCC and IC requirements for SAR and MPE. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FCC Caution
Changes or modifications not expressly approved by the part responsible for
compliance could void the user’s authority to operate the equipment.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.”
RSS-Gen & RSS-247 statement:
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
- this device may not cause interference, and
- this device must accept any interference, including interference that may cause undesired operation of the device.
Software Installation
Wi-Fi:
The SW driver is already installed to TV software platform. Proper country
information must be selected from UI during first time boot up settings.
Country information is used to disable (deactivate) channels/frequency ranges
which are not allowed by country regulations. For the end-user following steps
describing how to setup on a product;
- Switch on your TV and using the navigation buttons choose Menu-Settings-Network Settings.
- Select Wireless Device.
- It will scan and list all available wifi networks. If the network you select is protected by a password, enter the correct password by using the virtual keyboard. Wait until the IP address is displayed, confirming a connection has been established. You can enable or disable a network connection by pressing OK button.
Bluetooth:
The SW driver is already installed to TV software platform which is a Linux
based OS. For the end-user following steps describing how to setup on a
product;
- Switch on your TV and using the navigation buttons choose Menu-Settings-Remote&Accessories.
- Select Auto link enable and scan.
- It will scan and list all available devices.
Country Regulations
Device is intended for home and office use in all countries and countries may have their own regulations to prohibit some wlan frequencies. Proper country information must be selected from UI during first time boot up settings. Country information is used to disable (deactivate) channels/frequency ranges which are not allowed by country regulations. Below are notes on use of devices in countries. For further information please refer to product IB or consult country regulatory organization.
Country | Restriction |
---|---|
Bulgaria | General authorization required for outdoor use and public service |
France | In-door use only for 2454-2483.5 MHz |
Italy | If used outside of own premises, general authorization is required |
Greece | In-door use only for 5470 MHz to 5725 MHz band |
Luxembourg | General authorization required for network and service supply (not |
for
spectrum)
Norway| Radio transmission is prohibited for the geographical area within a
radius of 20
| km from the centre of Ny-Ålesund
---|---
Russian Federation| In-door use only
Israel| 5 GHz band only for 5180 MHz-5320 MHz range
Basic transmitter specification is givens below figure
Frequency Ranges | Max Output Power (eirp) |
---|---|
2400 – 2483,5 MHz (CH1-CH13) | < 100 mW |
5150 – 5250 MHz (CH36 – CH48) | < 200 mW |
5250 – 5350 MHz (CH52 – CH64) | < 200 mW |
5470 – 5725 MHz (CH100 – CH140) | < 200 mW |
List of applicable FCC-rules
FCC-Rules
FCC CFR47,Chapter I, Subchapter A, Part 15 Subpart C Intentional Radiators
- 15.203 Antenna requirement.
- 15.205 Restricted bands of operation.
- 15.207 Conducted limits.
- 15.209 Radiated emission limits; general requirements.
- 15.212 Modular transmitters.
- 15.247 Operation within the bands 902-928 MHz, 2400-2483.5 MHz, and 5725-5850 MHz.
Radiofrequency Radiation Exposure
- FCC CFR47, Chapter I, Subchapter A, Part 2, Subpart J, §2.1091 Radiofrequency radiation exposure evaluation: mobile devices.
- FCC CFR47, Chapter I, Subchapter A, Part 1, Subpart I, §1.1310 Radiofrequency radiation exposure limits
- FCC CFR47, Chapter I, Subchapter A, Part 15
- Subpart E—Unlicensed National Information Infrastructure Devices §15.407 General technical requirements.
Note: Attention to host manufacturers, further testing is required.
Test modes
Test tools of Mediatek (QA tool) allow to configure test modes for different operational conditions. Below steps should have been followed for testing Tx power on module.
On TX/RX page
- Select TX sub-page as following figure.
- Set Channel/Mode/Rate.
- Set BW. (Generally, System BW= Pre-Packet BW).
- Select “Nss=1 or Nss=2” and choose “TX/RX0″or “Tx/RX1” to do transmitting.
- Click “Start Tx and waiting for a while then click “Stop Tx” (Please repeat this step if user change channel/BW/Rate)
- Choose “Payload OFDM”.
- Check “Conti. Tx” to start Tx 100% duty packet transmitting and uncheck “Conti. Tx to stop.
- Users can click “”button to modify power level of transmitting signal after uncheck “Conti. Tx”.
- Users can click ” button to modify frequency offset of transmitting signal after uncheck “Conti. Tx.
Below steps should have been followed for testing Rx on module.
On TX/RX page
- Select RX sub-page and “Normal Mode” as following figure.
- Set Channel frequency.
- Set BW. (Generally, System BW =Pre-Packet BW).
- Select “Nss=1” and choose “TX/RXO” to do receiving.
- Click 1 Start RX ” button to receive WIFI packets.
- Enable WIFI signal generator to transmit packets. Click Stop RX” button to stop receiving.
- Successful received packets number would be shown at “RX OK” area and RSSI shown at “inst RSSI IB RO” area.
- Users can click “Reset counter button to reset counter value.
15 ISED
- The device for operation in the band 5150–5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems; le dispositif utilisé dans la bande 5150- 5250 MHz est réservé à une utilisation en intérieur afin de réduire le risque de brouillage préjudiciable aux systèmes mobiles par satellite dans le même canal.
- The host product shall be properly labelled to identify the modules within the host product. The certification label of a module shall be clearly visible at all times when installed in the host product; otherwise, the host product must be labelled to display the certification number for the module, preceded by the word “contains” or similar wording expressing the same meaning, as follows:
- Contains FCC ID: 2AVQS-17WFM26,
- Contains IC: 25888-17WFM26.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>