LIVINOX LCH-ROSE-90BL Builders Hardware User Manual

: June 10, 2024
: LIVINOX

Table of Contents

From the Manufacturer
Safety Instruction
Dimension Diagrams
Instructions for use
- Cleaning & Maintenance
Installation
Safety Information
Trouble shooting
Documents / Resources
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)

LIVINOX LCH-ROSE-90BL Builders Hardware

LIVINOX LCH-ROSE-90BL Builders Hardware

From the Manufacturer

Please read this user manual carefully before attempting to operate the appliance and keep it in a safe place for future reference.
This appliance and its packaging are produced by processes that minimize waste and respect the environment. Please help us to continue this effort to protect the environment by using the appliance efficiently and dispose of the packaging in a responsible manner

FOR THE USER

Safety Instruction

Warning

**** PLEASE READ THIS SECTION THOROUGHLY BEFORE ATTEMPTING TO OPERATE THE APPLIANCE

To ensure adequate ventilation in the room when the range hood is in use at the same time as gas/fuel burning cooking appliances (this is not applicable to appliances that only discharge the air back into the room).
There is a fire risk if cleaning is not carried out in accordance with the instructions.
To avoid using food products that produce flame under the range hood.
Do not “flambé“ food (is a cooking procedure in which alcohol is added to a hot pan to create a burst of flames) under the range hood.
Sufficient air is needed for proper exhausting of gases through flue (chimney) of fuel burning appliances.
This appliance is not intended for use by persons (including children) with reduced physical, sensory, mental capabilities, lack of experience and knowledge.
To reduce risk of fire and to properly exhaust air and to ensure to duct air outside. Do not vent exhaust air into spaces within walls, ceilings, into attics and crawl spaces.

Installation

This appliance must be installed or repaired by a qualified technician only.
Do not modify any part of this appliance by yourself.
To ensure the location in which this appliance is installed has good and permanent ventilation.
In ducted mode, there must be one or more permanent air inlet. The air collected must not be discharged into a duct used to blow off smoke from other appliances fed with electricity.
The distance between the bench to the lower part of the hood must not be less than 300-350mm.
Use an electrical connector with earth that is correct for your location.
To check the voltage in your area correspond to the appliance as indicated on the rating label.
Do not connect the hood to a duct that carries combustion fumes (e.g. fireplace).

Intended For Household Use

This product is designed for household use only and should never be used for commercial applications.
After use, always ensure that all controls are in the “OFF” position.
When frying with a gas flame, take particular care not to allow the oil or grease in the pan to catch fire.

Cleaning, Maintenance & Service

It is very important to clean and maintain the grease filters regularly (at least once monthly) to improve its efficiency in eliminating heat and contaminated air in the kitchen. Heavy oil deposits is a fire hazard. Hood surface should be cleaned with soft cloth and non-corrosive detergent. Important: Never attempt to repair this appliance by yourself. Always refer to qualified Service Technicians. For safety precaution, always purchase the original replacement parts. Always switch off the power and unplug the connection before conducting maintenance or cleaning.

Electrical Cord

To ensure the electrical cord is not exposed to heat, chemical or sharp objects.
If the electrical cord is damaged, it must be replaced by the manufacturer or its service agent or qualified electrician.

Dimension Diagrams

Instructions for use

Press A : Power turn on and default on low speed function (LED screen shows”F1”). Press it again, delay shutdown for 1 minute, there will be alarm warning (3 seconds before closing),Press A again to turn off power.
Press B : Light will turn on. Press it again, light will turn off.
Press C : When the fan is working at high speed (LED screen shows “F3”), Press C once, the fan runs at mid speed (LED screen shows “F2”). Press C again, the fan runs at low speed (LED screen shows “F1”).
Press D : When the fan is working at low speed (LED screen shows”F1”), Press D once, the fan runs at mid speed (LED screen shows “F2”). Press D again, the fan runs at high speed (LED Screen shows “F3”).
Press E : Hold for 3 seconds, oil removing function will operate for 10 minutes. Press again, turn off oil removing function. The fan will automatically operate at high speed for 1 minute after the 10 minutes cleaning function

motion sensor

Within 10-15cm distance from the switch, wave once from left to right to turn on power (LED screen shows ”F1”). Wave to the right, the fan runs at mid speed (LED screen shows “F2”). Wave to the right again, the fan runs at high speed (LED Screen shows “F3”). “Repeat this cycle”
Within 10-15cm distance from the switch, wave once from right to left to turn off power.

Cleaning & Maintenance

ALWAYS SWITCH OFF AND UNPLUG FIRST!

SURFACES:

Wash with warm soapy water and a soft sponge. Never use abrasive detergent, scouring pads, steel wool or
solvents on any part of this appliance as this will cause irreparable damage.

ALUMINIUM NET:

Wash in the dishwashers or soak the panels in a degreasing agent for an hour, then rinse off and dry before reinstalling.
For this appliance to function effectively, regular maintenance is a must.
Clogged filters restrict airflow and may cause the motor to overheat.

Installation

Use suitable bolts to mount the appliance on a secure surface.
The minimum distance between the supporting surface for the cooking vessels on the hob and the lowest part of the range hood. When the range hood is located above a gas appliance, this distance should between 300 350mm. If the instructions for installation for the gas hob specify a greater distance, this has to be taken into consideration.
To obtain best performance, it is advisable to install in an air ventilated area.
Do not install the outlet of the exhaust duct in the wind direction, which can prevent the exhaust air from flowing backward.
Fasten the components on exhaust outlet with screws. To perform for smooth airflow, the exhaust duct should bend in L-shape till exhaust outlet

NOTE: Fixing Screws bag should contain :

Screw Size

ST4.8 x 3PCS| M4-10 x 4PCS| M4-8 x 15PCS| ST2.9-12 x 2PCS
ST3.9-25 x 4PCS (including 4PCS plastic expansion bolt)| ST5-40 x 3PCS (including 3PCS plastic expansion bolt)
1M grey sponge tape

Complete components include as follow :

Installation

Use a phillips screwdriver to loosen the two pieces of screws on the left and right side and remove chimneys as per below fig.：
Install duct cover：
Please remove the sponge tape and adhere it under the bottom of the duct cover. Remove the four screws (M4*16mm) from motor outlet, Fix the duct cover onto fan assembly as per below fig.

Please connect the wires between fan assembly and chamber assembly as per below fig
Fix the Fan Assembly & Chamber Assembly by using the 10 pcs M4x8mm screws to tighten it as per below fig.
LED light plug must pull out from the hole to enable the connection to LED lamp.
Install the Exhaust Duct: Fix the Exhaust Duct and duct cover tightly with 2 pcs ST2.912mm screws. Then fix 2pcs M410MM screws to each side of the body. Remarks: Do not screw too tight, keep about 5mm gap between the body and M4*10mm screw head as per below fig
Install The Hook ：Measure a standard hanging height and pre-drill 3 holes by horizontal position on the wall, and drive the plastic expansion bolt into the holes. Use 3pcs ST4.8 screws to fasten the hook on wall firmly.
Install the fan assembly into the chamber assembly and align the second holes with 2pcs M4 screws. Connect LED light plug into fan assembly
1st chimney and ducting cover bracket connection : Use a philips screw driver to fix the ducting cover bracket into the extra chimney with 2 PCS Screws M4*8 mm as below fig.：
Install the cooker hoodl: Hang the complete set onto the hook firmly.
2nd Chimney installation: Measure a suitable height for 2nd Chimney and pre-drill with 2 screws holes by horizontal position on wall. Insert the plastic expansion bolt into the holes and tighten the ducting bracket by 2 pcs ST3.8*25mm screws. Pull up the 2nd chimney to fix on the bracket.

FOR THE INSTALLER

Safety Information

Electrical connection must be in accordance with the local standards and laws.
To ensure that the electrical supply in compliance with the appliance setting, otherwise, do not connect.
To ensure the power supply cord is free from any heat source or sharp objects.
The electrical connection of this appliance must be soundly earthed. In the event of electrical short circuit, grounding reduces the risk of electrical shock. If unsure, contact a qualified electrician.
Replacement of lamp must not exceed 20W.
LED lamp must not exceed 1.5W/7W.

**** Wire Color Codes:
Green & Yellow = EARTH
Blue = NEUTRAL
Brown = LIVE

Trouble shooting

Problems	Possible Cause	Action
Not function	No power supply	**Check that the main switch is

turned on
Check that the plug is connected
Poor airflow| Aluminum grease filter clogged| Clean the filters and replace when dry
Charcoal grease filters clogged| Replace charcoal filters with new sets
Motor running but no airflow| Butterfly valve jammed| Contact technician
Motor cuts after a few minutes| High temperature safety device activated| The kitchen is not sufficiently ventilated
The hood is installed too near the cooking stove| The hood must be at least 300mm from stove
Strong cooking smell| Airflow weak/ventilation clog| Clean the Aluminum filter and replace when dry. Check duct cover valve, contact technician if jammed.
Oil dripping| Oil cup missing or not installed| Remove aluminum filter and replace oil cup
aluminum grease filter saturated| Wash the aluminum grease filters
Whirring sound| Abnormal object clog on fan blade| Contact technician**