LIVINOX LGH-MAPLE 2BA-BL 2 Burner Glass Hob Instruction Manual
- June 10, 2024
- LIVINOX
Table of Contents
MAPLE 2BA-BL 2 Burner Glass Hob
Instruction Manual
LGH-MAPLE 2BA-BL 2 Burner Glass Hob
Dear Consumer,
Thank you for your purchase of our products. To ensure you use the appliance
in the best effect, please read this instruction manual with care before using
and save it for future reference.
The manufacturer declines all responsibility for damage to persons or things
caused by non observance of the above prescriptions or by interference with
any part of the appliance or by the use of non original spares
SPECIAL PRECAUTIONS
To avoid any danger and loss when using the hob, we make below mark. Below is
all about special precautions. Please pay full attention to it and operate ina
right way.
Marks are identified by different danger and loss level
If ignoring this mark and operate unproperly, it may lead die, hurt or fire.
ATTENTION If ignoring this mark and operate unproperly, it may lead die,
hurt or fire.
ADVICE In order to be safe and convenient when using it, please kindly
understand this content.
Marks for ATTENTION
DANGER
When gas leakage
1.stop using the hob immediately.
2.turn off the gas valve
3.open windows and doors
4.contact the local gas company
| If case of gas leakage
do not ignite any fire.
do not turn on any electrical appliance
do not touch power plug
do not use telephone nearby
Flame spark will lead fire.
---|---
When feeling strange burning, or smell
gas, or in case of earthquake, fire, please do as below:
1.turn the knob to OFF position
2.turn off the gas valve
3.contact our after-sale service dept immediately
Above is to avoid fire or fault.| Please use the right type of gas according
to the rating label.
If use the gas other than that are appointed, it may leads gas cooker damage
or even fire.
To install, repair, move a gas appliance, must be carried out by our service
apt., or a registered gas installer. Otherwise, we will not take the
responsibility for any damage.| Any easy-burned item like clothes, newspaper,
coal oil, can not be put nearby the hob.
It may lead fire.
Any repair, disassembly must be carried out by registered technical people.
Or else, it may leads fire or fault.|
Must use the specified gas pipe.| Do not use coal oil, gas oil, or other
easy-burning and explosive product nearby the hob. It may lead fire.
Do not put any spray container nearby the hob. It may lead fire.|
ATTENTION
There should be space of at least 400mm height between the hob bottom and
cupboard. And the space can not be sealed, with hole of diameter not less than
0.2 sq| There should be space between hob and items nearby. (not less than
150mm from the wall, 1mm from above)
---|---
Gas container can not be put right below Or hob. Gas pipe not more than 2
meters.| The hob should be kept more than meter away from the gas container.
Gas pipe can not reach other part of the hob.
To ensure the burner and trivet are put in the right place before using the
hob.| Keep the kitchen in ventilated situation. But do not let strong wind
to below the burner directly.
Do not touch the trivet and burner immediately after using it, because
they’re very hot.| Q Tum the knob to OFF and turn off the gas was brake where
job eon out ar eat Seep.
ADVICE
Check whether the gas pipe are in a good situation sometimes. The pipe should
be changed for every two years.
PARTS IDENTIFICATION
1.PARTS IDENTIFICATION
Remark: above is the built-in hob structure and part identification. Other type of hob can refer to above picture.
INSTALLATION
-
Open holes in the cupboard:
Open holes in the cupboard with the instruction paper in the package. (see picture 3) -
Install the gas pipe
A. If to use plastic tube: put in the airproof caution, connect the tube and hob connector, fasten the clip. (see picture 4)
B. If to use metal tube: put in the airproof caution, fasten the nuts on the connection. (See picture 5) -
Put the hob in the right hole on the cupboard, check whether it’s installed in a balance. The bottom of top plate should be stuck with seal packing.
-
check leakage: turn on the gas valve. check whether with soap water there’s leakage in the connection. If any leakage, it needs to be reinstalled.(there’ll be air bubble for leakage).
DIRECTION FOR USE
Ignition safety hob have flame failure protect device. When accident flame failure occurs by wind or spilled liquid, the flame failure protect device will shut the gas supply automatically.
- put in battery properly. (battery case in the right-front side at the hob bottom).
- turn on the gas valve
- Turn the knob left until it reaches the full on position (about 90 degree anti-clockwise). Having heard the sound of continuous sparks, simultaneously the burner will be ignited. Keep pushing the knob for 5-8 seconds before taking your hands off.
- you can choose five different fame by turning the hob.
- turn the hob to OFF by clockwise. After continuous sound, the gas supply will be broken, and flame out.
NOTE:
- For the newly installed hob or hob not used for some time, it may fail to ignite at first time, because there’s air in the tube. You can repeat until the air is exhausted out, then it can work.
- If there’s yellowish flame or uneven flame, adjust the damper at the bottom to get an normal flame.
PRODUCT DIMENSIONS
CLEANING AND MAINTENANCE
To ensure the hob can be used properly, the clearance and maintenance is
necessary. Keep the hole of burner cap and gas flow not to be stuff. Keep the
electrode and thermocouple clear. Before clearing and maintenance, shut off
the gas supply and let all parts cold.
Wash burner caps, burner, electrode, thermocouple and trivets with mild
detergent when they’re dirty. Then put them back to their proper position. Use
steel wire to clear the dirt in the burner cap. When the top plate get dirty,
never use any sharp or hard brush but only sponge brush with mild detergent to
clean them.
To check the gas tube often, and change new gas tube for every two years.
TROUBLE-SHOOTING GUIDE
| Trouble | Cause | Remedy |
|---|---|---|
| Burners can not be ignited. | Gas supply is not opened | Turn on the gas |
| Gas type is bent or crushed. | Straighten or changing the tube | 0 |
| Short of gas supply | Replace it | 0 |
| Air remains in the gas piping | Repeat igniting operation until all air in the | |
| piping is purged out. | 0 | |
| Electrode not in right position | Adjust it’s position | |
| Small spark when ignition operation | Clear the Electrode | 0 |
| Out off battery | Replace or install the battery | 0 |
| Electrode broken | Replace the ignition electrode | |
| Flame is extinguished | Thermocouple dirty., broken, or not in right position | |
| Clear or replace it, or adjust it’s position | ||
| Electromagnet valve broken | Replace it | |
| Valve broken | Replace it | |
| Uneven flame in thermocouple | Adjust the damper | 0 |
| Gas leakage (or smell of gas) | Cracks or holes in Gas pipe | Replace it with a |
| new one | ||
| The main flame of burners is not ignited | Ignite again after the gas is clear | |
| in the air. | 0 | |
| Gas valve is not well sealed | Replace gas valve | |
| Sealing packing for gasvalve is broken | Replace the sealing packing. | 0 |
| Flame not regular | Burner cap not in proper positior | Put it to proper |
| position | 0 | |
| Week flame | Gas pressure not enough | Check the gas flow |
| Flame easy to fall | Damper hole is too big | Adapt the damper |
| Long and yellow flame | Damper hole is too small | Adapt the damper |
| Uneven flame | Hole for burner cap is stuff | Clear the hole |
Remark: Trouble with mark “‘ O ”can be solved by final users. Trouble with “A” must be repaired by technical people.If final user can not solve problem according to above guide, call our after-sale service.
LIVINOX Malaysia Sdn Bhd
Blok B-1-29, Dataran Cascades
NO.13A, Jalan PJU5, Kota Damansara
47810 Petaling Jaya, Selangor.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>